Wed7ohebwo Parts

This bulkhead is the front structural panel that supports the dryer drum and seals the front of the cabinet to maintain proper airflow and drum alignment. Replacing a worn bulkhead restores stable drum rotation and prevents air leaks. What it does:

• Supports the drum and front bearing to keep the drum centered and turning smoothly
• Seals the front cabinet to direct exhaust airflow through the blower and vent
• Reduces rubbing and vibration caused by a damaged or warped bulkhead
• Helps eliminate airflow leaks that can extend dry times or cause overheating warnings

• One bulkhead

• Disconnect power (and gas supply if applicable) before any service
• Service typically requires removing the dryer front panel and drum for access
• Inspect and replace any worn gaskets, bearings, or fasteners while replacing the bulkhead

This thermostat is the temperature-sensing switch that helps the appliance maintain its set temperature for reliable operation. It replaces a failed temperature control that causes improper heating or cooling performance. What it does:

• Senses temperature and opens or closes the circuit to control heating/cooling cycles
• Prevents overheating by interrupting power when temperatures exceed set thresholds
• Restores normal cycling when the control no longer conducts (common with failed thermostats)
• Common symptoms include the appliance not reaching or holding temperature, cycling too frequently, or running continuously

• One thermostat

• Disconnect power before servicing to avoid shock or injury
• Follow the appliance service manual for removal and proper wiring location
• Verify electrical continuity of the old and new thermostat with a multimeter before and after installation

This replacement pad cushions contact between components to reduce noise, vibration, and surface wear. Use it to restore stable, quieter operation and protect mating surfaces from damage. What it does:

• Cushions contact points to minimize rattling and vibration
• Helps prevent surface scuffs or wear where parts meet
• Can reduce squeaks and intermittent noise caused by loose contacts
• Restores proper component seating for more consistent operation

• Disconnect power before accessing internal components
• Remove the old pad and press the new pad into the same location until fully seated
• Use only the specified pad for the designated mounting point; do not modify

This water inlet valve controls incoming water flow to the appliance, restoring proper supply to the ice maker or dispenser. Replacing a faulty valve helps stop leaks, restore water delivery, and prevent continuous filling. What it does:

• Opens and closes to allow water into the appliance when the dispenser or ice maker calls for it
• Stops water flow when the dispenser or ice maker is idle, preventing overfilling or leaks
• Commonly linked to symptoms like no water from the dispenser, no ice production, or continuous/slow filling
• Works with the appliance's electrical solenoids to regulate water delivery on demand

• One water inlet valve assembly

• Disconnect power and shut off the water supply before starting any repair
• Use proper tools and tighten fittings to manufacturer torque—avoid overtightening plastic fittings
• Inspect water lines and seals; replace damaged hoses or gaskets to ensure a leak-free installation

Thermal cutoff is a temperature-sensing safety device that opens the circuit to stop heating when temperatures get too high. Replace a failed cutoff to restore over-temperature protection and help prevent overheating-related damage. What it does:

• Opens the electrical circuit when internal temperature exceeds safe limits to stop heating elements.
• Prevents continued operation during overheating, protecting components and reducing fire risk.
• A failed cutoff can cause no heat, intermittent heating, or an appliance that shuts off unexpectedly.
• Works as a safety interlock — do not bypass or replace with non-equivalent parts.

• Disconnect power to the appliance before accessing or replacing the cutoff.
• Located on the heater assembly or control housing; follow the model's service manual for access.
• Replace in the same orientation and wiring configuration; secure all connectors and panels before restoring power.

This self-drilling screw secures appliance panels and components where a fastener must cut its own pilot hole. It provides a quick, reliable hold for repair or reassembly of trim, brackets, and internal fixtures. What it does:

• Fastens panels, brackets, and small components without pre-drilling
• Helps stop loose or rattling trim and parts caused by missing or worn screws
• Restores proper alignment and secure mounting after repairs
• Works where sheet metal or thin substrates require self-tapping engagement

• One self-drilling screw

• Disconnect power and follow appliance safety procedures before starting repairs
• Use the correct size driver and steady pressure to avoid stripping the head
• Start straight and apply firm, even torque; avoid overtightening which can damage mounting surfaces
• Wear eye protection and handle small fasteners carefully to avoid loss or ingestion hazards

This thermostat is the temperature control switch that regulates cooling cycles to help keep your refrigerator at the right temperature. Replaces a worn or faulty control to restore consistent cooling performance. What it does:

• Senses cabinet temperature and opens/closes the cooling circuit to maintain set temperature.
• Starts and stops the compressor and/or evaporator fan based on temperature demand.
• Commonly used when the fridge runs constantly, doesn't cool enough, or cycles on and off too frequently.
• Works with mechanical temperature control systems.

• Disconnect power before diagnosis and replacement to avoid electric shock.
• Mount in the original location and route capillary/tubing per original routing; avoid kinks.
• Test operation after installation by allowing the unit to run through a full cycle.

This metal hose clamp secures flexible water or drain hoses to fittings to help prevent leaks and hose detachment. It's a compact replacement part for appliances that use band or spring-style clamps on hose connections. What it does:

• Holds a hose firmly on a barb or nipple to maintain a watertight connection
• Prevents leaks or dripping at hose junctions caused by loose fittings
• Reduces hose movement and vibration that can lead to wear or disconnection
• Works wherever a small appliance hose clamp is required

• Turn off and unplug the appliance and shut off water supply before starting
• Release hose pressure and drain residual water before removing the old clamp
• Use appropriate pliers or a screwdriver for the clamp type; avoid over-tightening

This 8 ft flexible exhaust hose directs airflow from the appliance to the home vent, helping maintain proper ventilation and reduce moisture and lint buildup. It's a straightforward replacement for worn or damaged ducting. What it does:

• Channels exhaust air from the appliance to the exterior vent
• Restores proper airflow to help reduce drying times and moisture buildup
• Helps prevent lint accumulation in the appliance exhaust pathway
• Reduces risk of poor performance caused by crushed, torn, or disconnected ducting

• One 8 ft flexible exhaust vent hose

• Disconnect power to the appliance before replacing the vent and follow all safety precautions
• Remove old ducting carefully to avoid scattering lint; clean vent openings before installing the new hose
• Ensure secure clamps or connections at both appliance and wall/roof vent to prevent leaks
• Follow local building codes and venting recommendations for appliance type and location