Wed7ohebwo Parts

Color: White

This rear panel is the exterior back cabinet piece that covers and protects a dryer or washer's internal components and provides mounting support for rear-mounted parts. It restores the appliance's structural back and keeps lint, moisture, and debris out. What it does:

• Covers and protects internal components, wiring, and controls located at the appliance rear
• Provides mounting points and alignment for rear-mounted parts and brackets
• Helps reduce drafts, lint intrusion, and pest access through the appliance back
• Stops rattles or vibrations caused by a damaged or loose back panel

• One rear panel/cabinet back

• Disconnect power and water before starting; verify the appliance is fully de-energized
• Remove the dryer/washer top and/or access screws to detach the old rear panel; retain fasteners if reusing
• Align panel tabs and mounting holes, then secure with the correct screws; avoid over-tightening to prevent damage
• If the panel is rusted or sharp, wear gloves and eye protection during removal and installation

This is a replacement sheet-metal screw used to secure panels and components on compatible Whirlpool appliances. It provides a reliable fasten point for reattaching trim, brackets, and access panels after service. What it does:

• Secures appliance panels, brackets, and smaller components to the cabinet or frame
• Helps restore original fit and finish after repairs or part replacement
• Prevents rattles or loose panels when properly installed
• Matches OEM thread size and head style for a correct fit

• Turn off and unplug the appliance before removing panels or installing hardware
• Use the correct driver bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing to prevent thread damage or warped panels

Color: White.

A front toe panel assembly that restores the lower front trim and airflow opening on compatible laundry appliances. Replaces a damaged or missing lower access panel to keep the cabinet sealed and looking finished. What it does:

• Covers the lower front of the appliance cabinet, protecting internal components from debris.
• Restores the lower air or vent opening and directs airflow as intended.
• Prevents items from falling under the appliance and reduces drafts at the base.
• Helps maintain proper appearance and fit of the appliance front.

• Disconnect power (and gas if applicable) before starting any work.
• Install requires removing the appliance kick strip or lower access fasteners; retain hardware as needed.
• Align panel tabs/clips with cabinet slots and secure with the original screws or clips.
• Replace any damaged clips or mounting hardware to ensure a secure fit.

Size: 6 - 20 x 1 1/16 inch.

This lint duct assembly channels dryer exhaust through the cabinet and toward the vent, helping trap lint and maintain airflow for efficient drying. Replace a damaged or clogged duct to restore proper venting and reduce lint buildup. What it does:

• Directs exhaust air from the drum to the vent path to support consistent drying performance
• Helps contain and route lint toward the lint trap area to reduce internal buildup
• Common part for symptoms like poor drying, overheating, unusual airflow, or visible lint leaks inside the cabinet
• Works with the dryer cabinet and venting components to maintain safe exhaust flow

• One lint duct assembly

• Disconnect power (and gas supply, if applicable) before service to avoid shock or injury
• Inspect surrounding seals, gaskets and the lint trap for damage during replacement
• Reinstall using OEM fasteners and confirm proper alignment to prevent exhaust leaks

This name plate is the decorative centennial badge that restores the appliance's exterior appearance and branding. It replaces a missing, damaged, or faded badge to keep the unit looking factory-finished. What it does

• Restores the appliance's exterior badge for a like-new appearance
• Replaces badges that are cracked, scratched, peeling, or discolored
• Helps identify the appliance style when the original emblem is missing
• Cosmetic part only — does not affect appliance operation

• One name plate

• For best results, clean the mounting area and remove dirt or wax before installation
• Handle carefully to avoid scratching the finish; use non-marring tools as needed
• If access behind trim is required, unplug the appliance or disconnect power before removing panels
• Follow OEM instructions for removal and reinstallation to avoid damaging clips or surrounding trim

This 6-foot, 4-prong range power cord provides a dedicated 240V connection for electric ranges and stoves, replacing worn or damaged cords to restore reliable power and reduce risk of arcing or intermittent operation. What it does

• Supplies 240V/30A power to the range via a 4-wire (hot/hot/neutral/ground) connection
• Replaces cords with frayed insulation, exposed conductors, or melted ends
• Stops symptoms such as no power to the range, tripping breakers, or intermittent heating
• Ensures a grounded connection when installed correctly

• One 6 ft, 4-prong (30 amp) range power cord, bagged

• Always disconnect household power at the breaker before starting work
• Use the existing strain relief or mounting bracket to secure the cord and prevent tugging

The Seal is an OEM replacement part for Whirlpool dryers. It creates a tight seal between the dryer door and the drum, preventing heat and moisture from escaping during the drying process. It helps maintain the proper temperature inside the dryer, allowing your clothes to dry quickly and evenly.

Symptoms of a faulty door seal include:

• Heat escaping from around the dryer door
• Excessive moisture or lint buildup
• Extended drying times

A bad door seal can occur due to regular use, wear and tear, or accidental damage. If you notice issues such as heat escaping from around the dryer door, excessive moisture or lint buildup, or clothes taking longer to dry than usual, it may be time to replace the door seal.

This Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This replacement door strike provides the solid catch point the latch/lock grabs so the appliance recognizes the door or lid is closed and can run safely. A worn, bent, or broken strike can interrupt operation. What it does

• Forms the fixed catch for the door/lid latch or lock
• Helps actuate the interlock/safety switch so a cycle can start
• Misalignment or damage can keep the door from latching and stop cycles
• Common symptoms: door/lid won't latch or stay closed, unit won't start, "Door/Lid" or "Lock" message, needing to hold the door shut, visible cracks or wear on the strike

• 1 strike

• Disconnect power to the appliance before servicing
• Open the door/lid and remove the mounting screws securing the old strike; retain hardware if it is reused
• Position the new strike in the same orientation and tighten screws snugly; avoid over-tightening to prevent damage
• Close and open the door/lid to confirm smooth latch engagement, then run a brief test cycle

This seal creates a tight barrier between two mating surfaces in your appliance, helping prevent leaks and performance loss. Replacing a worn seal restores proper containment and helps protect nearby components from moisture intrusion. What it does

• Forms a tight barrier to prevent water or air from escaping between joined parts
• Helps maintain proper pressure, airflow, or water path as designed
• Replaces cracked, flattened, or torn seals that compromise performance
• Common symptoms: drips or moisture at the joint, visible wear or deformation, loose fit, recurring leaks after reassembly

• 1 seal

• Disconnect power and, shut off the water supply before servicing
• Note the seal's orientation and match the new part to the old one
• Clean and dry mating surfaces; remove old adhesive, debris, or scale
• Install per OEM orientation; only lubricate if specified by the manufacturer, then reassemble and test for leaks

The CONTROL BOARD is an OEM component specifically designed for Whirlpool brand electric dryers. It houses the electronic control system that monitors all cycles and safety features based on input signals. 

Symptoms of a bad control board include:

• Repeated error codes and faulty drying sequences   
• Failure to advance drying stages or tumble as intended  
• Failure to respond appropriately to input selections

As an electronic component, the control board faces wear from repetitive usage over many drying cycles. Exposure to moisture or impacted energy surges also risk damage over the years. Replacing it with this genuine Whirlpool part restores full oversight and dependable automatic operation cycle after cycle. Reliable electronic governance fulfills core drying functions.

This OEM Whirlpool replacement control board is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore dryer models. Proper monitoring streamlines laundry and maximizes performance.