Wed7ohebwo Parts

The Control Board is an OEM component specifically designed for Whirlpool brand dryers. This control board houses the electronic components that operate and monitor dryer functions such as drying settings, cycle monitoring, heating elements and more. 

Symptoms of a bad control board can include:

• Fault codes or error messages appearing on the display 
• Failure of heating elements to turn on or temperature levels to rise
• Dryer not starting or completing cycles properly

Causes of a bad control board are typically due to long term usage and exposure to environmental conditions inside the dryer. This can lead to degraded electronic performance over time.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Door Switch is an OEM component specifically designed for Whirlpool brand dryers. This door switch works to detect when the dryer door is open or closed and cuts power to internal components when the door is open for safety. 

Causes of a bad door switch can include wear and tear over time, exposure to excessive shock or impact, or moisture damage. 

Symptoms of a bad door switch include: 

• The dryer operates with the door open 
• Inability to start or run the dryer
• Error codes or fault messages relating to door detection

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models. 

This electronic control board is the appliance's central controller. It regulates power and timing to key components and interprets inputs from the controls and sensors to ensure the unit operates as designed.

• Manages control logic and timing for programmed operations
• Distributes power to loads such as motors, valves, heaters, and fans
• Interfaces with the user interface and sensors to start, monitor, and complete functions
• Common failure symptoms: won't power on or start, unresponsive controls, stops unexpectedly, intermittent operation, or control-related error codes

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle the PCB by the edges and use ESD protection to avoid static damage
• Label or photograph wiring; transfer connectors to the new board one at a time
• After installation, perform any model-specific reset or diagnostic procedure per the service manual if required

The Window is an OEM part for Whirlpool dryers. It forms the inner layer of the dryer door, providing insulation and protection to the contents inside the dryer drum. This inner window ensures a clear view of the drying process while preventing heat loss and potential damage to the outer door.

A bad door inner window can occur due to accidental impact, wear and tear, or improper handling. If you notice symptoms such as cracks, fogging, or damage to the inner window, it may be time to replace this part.

Symptoms of a bad door inner window include:

• Visible cracks or damage
• Fogging or cloudiness
• Compromised insulation

Restore your Whirlpool dryer by replacing the faulty or damaged door inner window with this genuine OEM part.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

The Filter Housing is an OEM part for Whirlpool dryers. As part of the dryer ventilation system, the filter housing holds the lint filter in place, trapping lint and debris before it exits through the vent. It helps prevent blockages in the exhaust vent and surrounding area.

Causes of a bad filter housing can include cracks, breaks or defects in the plastic material over time due to normal use and heat exposure inside the dryer. Increased wear and tear from extended use can also cause damage.

Symptoms of a bad filter housing include:

• Excessive lint building up inside the dryer
• Reduced air flow and inefficient drying times
• Strange sounds like vibrations or rattling coming from the vent area
• Lint escaping from gaps in the filter housing

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This drum baffle restores proper tumbling by lifting and separating laundry as the dryer drum rotates. It helps improve drying performance and reduces garment bunching. What it does:

• Lifts and tumbles clothes so air flows more evenly through the load
• Helps prevent garments from clumping or wrapping around the drum
• Can reduce rubbing, thumping, or scraping noises caused by a loose or damaged lifter
• Restores consistent drum contact and improves drying efficiency

• Disconnect power before starting any repair to avoid shock or injury
• Access typically requires opening the dryer cabinet or front panel; small tools may be needed
• Align the baffle with factory mounting holes and secure with existing fasteners; use correct screws if replacements are required
• Inspect and replace worn drum or support parts as needed for reliable operation

This spring provides tension for the door hinge, helping the door open and close smoothly and stay properly balanced. Replacing a weakened or broken spring restores correct door movement and prevents slamming or drooping.

• Maintains tension on the door hinge mechanism
• Helps the door stay level and close securely
• Can reduce issues like a sagging, loose, or slamming door
• Restores smooth, controlled door operation

• Disconnect power and shut off gas or water (as applicable) before service
• Support the door to relieve hinge tension prior to removal
• Note spring orientation/routing before replacing
• Wear cut-resistant gloves; hinge areas can be sharp and under tension

Small replacement clip that secures panels or small internal components to restore a snug fit and reduce rattling or misalignment. Use this clip when a worn or broken retainer lets trim or parts sit loose. What it does:

• Holds trim, panels or other small appliance components in place to maintain correct alignment.
• Helps eliminate rattling, vibration noise or gaps caused by a missing or damaged clip.
• Restores secure fit where a broken clip allows parts to shift or separate.
• Simple, low-profile replacement part used in affected Whirlpool appliances.

• Disconnect power (unplug or shut off breaker) before servicing any appliance.
• Small part; keep track of screws and retainers during disassembly.
• Basic hand tools may be required; trim or panel removal might be necessary to access the clip.

Dryer Vent Test Kit ensures your dryer's vent system is operating properly. Kit includes two tests depending on the location of your dryer's lint screen: One for the lint screen in the top of your dryer, and one for the lint screen in the front of your dryer. Instructions included.

The Leveling Leg is an OEM part for Whirlpool dryers. It is an adjustable component that lifts the rear of the dryer off the floor. The leveling leg allows for proper tilting and balance of the dryer drum for the most effective spinning and tumbling cycles. Its threaded shaft and rubber foot stabilize the dryer while enabling leveling adjustments to compensate for uneven surfaces.  This kit contains a set of 4 leveling legs

Causes of a bad leveling leg can include stripping or bending of the metal shaft from moving heavy loads or repeated leveling. The rubber foot may also flatten out over time.

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Replacement cover that protects and conceals internal appliance components by closing the housing. Keeps wiring and moving parts shielded from debris and accidental contact, restoring a finished appearance and safe operation. What it does

• Covers and protects internal components from dust, lint and accidental contact.
• Restores the appliance's cabinet/housing integrity after a cracked or missing panel.
• Helps stop rattling or vibration caused by loose or damaged covers.
• Use when you see visible cracks, broken tabs, missing fasteners, or an exposed area.

• Disconnect power (unplug or switch off breaker) before any service.
• Typically secures with simple fasteners; keep all clips and screws and replace any broken tabs.
• Handle edges carefully; use appropriate tools and avoid forcing tabs to prevent breakage.

This replacement steam spray nozzle directs steam into the appliance's steam system to help produce even steam flow for wrinkle reduction and refreshing cycles. It restores proper steam delivery when the original nozzle is cracked or clogged. What it does:

• Directs and shapes steam flow into the appliance's steam path for consistent operation.
• Helps restore normal steam performance when steam output is weak or uneven.
• Prevents misdirected steam that can reduce cycle effectiveness.
• Works as a direct replacement for a damaged, cracked, or clogged nozzle.

• One steam spray nozzle

• Disconnect power and water supply before servicing; allow the appliance to cool.
• Handle the nozzle carefully to avoid damage; inspect surrounding seals and fittings.
• May require basic hand tools for access; follow OEM instructions.

The Speaker is an OEM component specifically designed for Whirlpool brand washers. It alerts users with chime tones or voice prompts during cycle operation or any error states. Precise acoustic engineering allows for clear audio reception even amid operating vibrations. 

Symptoms of a bad speaker include: 

• No audio tones or voice prompts were heard  
• Muffled, distorted, or unusually loud sounds
• Speaker making rattling or buzzing noises

Causes can be damage from water damage, defects in the audio circuitry, or aging components. 

This speaker ensures optimal user communication. Without it, you cannot verify cycle progress or troubleshoot issues. Its dependable performance maintains the washer's convenience.

This Whirlpool OEM part fits perfectly while extending the equipment's lifespan. It is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This replacement screw secures appliance components in their intended positions. Swapping a missing, stripped, or corroded screw helps stop rattles and keeps panels, brackets, and internal parts tight for reliable operation.

• Fastens panels, brackets, or internal parts where specified by your model
• Helps reduce vibration and rattling caused by loose hardware
• Restores alignment when an original screw is missing or damaged
• Replace if threads are stripped, head is rounded, or corrosion is present

• Disconnect power and shut off water or gas before service
• Verify the exact location using your model's parts diagram/IPL
• Start threads by hand to avoid cross-threading; tighten only until snug
• Reuse any original washers, clips, or spacers if present

The Filter is an OEM part for Whirlpool dryers. The filter screens lint and dryer debris from exiting air. 

Causes of filter issues can include excessive lint buildup over multiple loads inhibiting airflow, tearing of fragile mesh from continuous vibration, or warping out of shape preventing a tight fit.

Symptoms of a dirty or damaged Filter are:

• Slow drying times as the condenser works harder
• Strange smells detected inside the dryer
• Increased level of lint left inside the dryer drum
• Visible lint accumulation behind the screen grille

This OEM Whirlpool replacement ensures smooth operation by continuously screening lint particles. Compatible models include some Kenmore and select KitchenAid condenser dryers.