Wed9371ylo Parts

Color: White

Flat metal washer that helps secure fasteners and evenly distribute load on mounting points. Replacing a worn or corroded washer restores proper fastener grip, reduces vibration, and stops loose or rattling parts. What it does:

• Provides a smooth bearing surface for nuts and bolts, preventing pull-through and damage
• Distributes clamping force to protect mounting surfaces and maintain alignment
• Helps reduce vibration and noise from loose or worn fasteners
• Replace when bent, corroded, cracked, or missing to restore secure mounting

• Always disconnect power to the appliance before beginning repairs; follow all safety precautions
• Use the correct size fastener and torque to avoid over-tightening or crushing the washer
• Inspect surrounding hardware and replace any damaged or corroded bolts, nuts, or brackets

This elbow redirects a fluid or air line inside the appliance to allow routing around components and tight spaces. It restores proper flow path and helps stop leaks or blockages when the original elbow is cracked or worn. What it does:

• Provides a sealed change of direction for a water, drain, or vent line inside the appliance
• Replaces a cracked or broken elbow that can cause leaks, water pooling, or reduced flow
• Re-establishes the correct routing to prevent kinks and stress on connected hoses or tubing
• Helps eliminate intermittent draining or venting issues caused by a damaged fitting

• Disconnect power and shut off water supply before accessing the part
• Verify orientation and routing before removing the old elbow to ensure correct reinstallation
• Inspect and replace any worn clamps, gaskets, or hoses when installing the new elbow
• Tighten fittings to secure but avoid over-tightening which can crack plastic components

This Y-shaped connector hose diverts water between two inlet lines to route supply where needed. It restores proper water flow paths and replaces damaged or leaking split-connection plumbing on compatible appliances. What it does:

• Splits a single water inlet into two outlets so water can serve two components
• Provides a sealed path to prevent cross-flow between lines
• Commonly replaced when the connector leaks, cracks, or becomes brittle
• Helps restore normal water delivery when a split supply is required

• Turn off the appliance and shut off the water supply before beginning.
• Inspect mating fittings and replace any damaged clamps or seals.
• Hand-start fittings to avoid cross-threading, then tighten securely; check manufacturer torque guidance if available.
• After installation, restore water and power and check all connections carefully for leaks.

Outer door glass that restores the oven door viewing window and replaces cracked, chipped, or broken glass so the door functions safely and looks like new. What it does

• Replaces damaged or shattered outer door glass to restore a clear viewing window.
• Stops rattling or loose glass caused by broken mounting points or cracks.
• Helps maintain proper door appearance and user visibility into the oven cavity.
• Useful when glass has visible chips, cracks, or safety concerns.

• One outer door glass

• Disconnect power to the appliance before beginning any repair.
• Handle glass with heavy-duty gloves and eye protection; glass can break unexpectedly.
• Replacing this part typically requires removing the oven door and disassembling panels—follow the OEM service manual or instructions.
• Inspect and replace any worn clips, screws, or seals as needed; do not overtighten fasteners.

Color: White. Size: 1 qt. can. Acrylic appliance paint.

This adhesive label replaces a worn, damaged, or missing information label on your appliance so model, serial, and warning details remain readable and the unit stays compliant with safety and service needs. What it does

• Restores legible model/serial/rating and safety information used for service and identification
• Replaces faded or peeled factory-applied adhesive labels
• Helps ensure important operating and safety instructions remain visible
• Improves appearance by covering damaged or discolored label areas

• Clean and dry the mounting surface thoroughly before applying the label
• Peel backing and press firmly, smoothing out air pockets for full adhesion
• Avoid stretching the label during installation; align carefully before contact
• If the label is near electrical components, disconnect power before working in the area

Replacement clip that secures trim, panels, or small components to restore proper fit and reduce rattling and vibration. Install when a worn or missing clip leaves trim or panels loose or causes intermittent noise. What it does:

• Holds trim, panels or small assemblies in place to prevent movement
• Stops rattling and vibration caused by loose parts
• Replaces broken or missing clips that allow gaps or misalignment
• Small, snap-in retainer shaped to match original attachment point

• Always disconnect power before servicing the appliance
• Access the clip location by removing the adjacent panel or trim per the OEM diagram
• Clip typically snaps into place; use needle-nose pliers or a flat screwdriver to remove the old clip if needed

This exhaust pipe routes exhaust air from the appliance to the home vent, restoring proper airflow for safe, efficient operation. Use when the original pipe is cracked, bent, or leaking. What it does:

• Channels exhaust gases and lint from the appliance to the external vent
• Prevents exhaust leaks that can cause poor drying or cooking performance
• Helps maintain correct airflow to reduce overheating and moisture buildup
• Fits where a damaged or corroded exhaust connection needs replacement

• One exhaust pipe

• Disconnect power (and gas if applicable) before servicing; follow appliance safety procedures
• Inspect surrounding seals and clamps; replace clamps or ducting if damaged
• Secure pipe with OEM-recommended fasteners and ensure vent path is clear

This exhaust pipe vents hot, moist air from the dryer to the home venting system, helping the appliance dry clothes efficiently and reduce indoor humidity. Replace a damaged or restricted pipe to restore proper airflow. What it does:

• Channels dryer exhaust air safely from the appliance to the exterior vent
• Helps prevent overheating and long dry times caused by restricted airflow
• Reduces lint buildup in the appliance by providing a clear vent path
• Commonly replaced when cracked, crushed, kinked, or badly corroded

• Disconnect power to electric dryers; shut off gas supply and disconnect for gas dryers before servicing
• Inspect existing vent path for additional damage or lint buildup and clean before installing
• Position pipe without sharp bends or kinks and secure with appropriate clamps or fasteners