Wedb850wq0 Parts

This replacement pad cushions contact between components to reduce noise, vibration, and surface wear. Use it to restore stable, quieter operation and protect mating surfaces from damage. What it does:

• Cushions contact points to minimize rattling and vibration
• Helps prevent surface scuffs or wear where parts meet
• Can reduce squeaks and intermittent noise caused by loose contacts
• Restores proper component seating for more consistent operation

• Disconnect power before accessing internal components
• Remove the old pad and press the new pad into the same location until fully seated
• Use only the specified pad for the designated mounting point; do not modify

This rear panel replaces the dryer's back bulkhead to restore the appliance's structural enclosure and help protect internal components from dust and debris. It provides a clean mounting surface for internal parts and improves cabinet integrity. What it does:

• Replaces a damaged, dented, or corroded rear cabinet panel
• Protects internal wiring, ducts, and components from external debris
• Restores proper mounting surfaces for internal assemblies and fasteners
• Helps maintain correct airflow paths by sealing the dryer cabinet

• One rear panel/back bulkhead

• Disconnect power (and gas if applicable) before beginning any repair
• Installation typically requires removing the dryer cabinet and several fasteners; keep hardware for reuse unless damaged
• Inspect and replace any worn gaskets, seals, or mounting clips while cabinet is open

This is a drum assembly intended for use with dryers. This part can be found inside the dryer and is responsible for holding clothing while a cycle is running. It holds wet laundry while loading the appliance. Over time and with use, the drum assembly can start to wear out. This can cause the dryer to squeal, start and stop during a cycle, make buzzing noises, or seize up.If the drum assembly is damaged, it will need to be replaced. Make sure to have basic tools and a pair of work gloves ready. The dryer should be turned off and unplugged from the wall. Raise the top panel, remove the front panel, and then remove the drum. The drum support roller should be taken out and installed on the new drum. Reinstall with the new component and reassemble all parts before use.The drum assembly is made to be used with dryers and washer/dryer combos from Inglis, Estate, Admiral, Crosley, Roper, Magic Chef, Amana, KitchenAid, Maytag, Kenmore, and Whirlpool. It is a genuine OEM replacement part that is sourced directly from the manufacturer. The part is sold on an individual basis.

This wire harness is the factory-style electrical assembly that connects and routes power and signal wiring between an appliance's components, restoring reliable electrical connections and control communication. What it does:

• Provides factory-routing for power and signal wires between control, motors, switches, and sensors
• Restores lost or intermittent electrical connections that can cause no-start, no-heat, or erratic operation
• Replaces damaged, frayed, or corroded wiring to reduce short or open-circuit failures
• Maintains correct connector fit and wire length to prevent strain and interference

• One complete wire harness assembly as shown

• Disconnect power (unplug or shut off breaker) before inspecting or replacing wiring
• Compare connectors and wire routing to the original harness before installation
• Use proper strain reliefs and routing; avoid sharp edges and heat sources when reinstalling

Color: White.

This replacement control knob restores safe, reliable control of a range or oven burner. It provides a secure grip and clear pointer so you can set heat levels accurately and replace a missing or damaged knob quickly. What it does

• Replaces a worn, cracked, or missing control knob so the appliance can be operated normally
• Provides a clear pointer for setting temperature or burner power levels
• Allows the shaft to be turned smoothly when selecting settings
• Helps prevent accidental changes caused by a damaged knob

• One control knob

• Disconnect power to the appliance (or shut off gas) before servicing
• Most knobs pull straight off the control shaft; inspect shaft for damage before installing
• Align the knob's socket and press on until fully seated; test operation after restoring power
• If the shaft or underlying control is damaged, replace the damaged component rather than just the knob

This 6-foot, 4-prong range power cord provides a dedicated 240V connection for electric ranges and stoves, replacing worn or damaged cords to restore reliable power and reduce risk of arcing or intermittent operation. What it does

• Supplies 240V/30A power to the range via a 4-wire (hot/hot/neutral/ground) connection
• Replaces cords with frayed insulation, exposed conductors, or melted ends
• Stops symptoms such as no power to the range, tripping breakers, or intermittent heating
• Ensures a grounded connection when installed correctly

• One 6 ft, 4-prong (30 amp) range power cord, bagged

• Always disconnect household power at the breaker before starting work
• Use the existing strain relief or mounting bracket to secure the cord and prevent tugging

This replacement door strike provides the solid catch point the latch/lock grabs so the appliance recognizes the door or lid is closed and can run safely. A worn, bent, or broken strike can interrupt operation. What it does

• Forms the fixed catch for the door/lid latch or lock
• Helps actuate the interlock/safety switch so a cycle can start
• Misalignment or damage can keep the door from latching and stop cycles
• Common symptoms: door/lid won't latch or stay closed, unit won't start, "Door/Lid" or "Lock" message, needing to hold the door shut, visible cracks or wear on the strike

• 1 strike

• Disconnect power to the appliance before servicing
• Open the door/lid and remove the mounting screws securing the old strike; retain hardware if it is reused
• Position the new strike in the same orientation and tighten screws snugly; avoid over-tightening to prevent damage
• Close and open the door/lid to confirm smooth latch engagement, then run a brief test cycle