Wee760h0dhd Parts

This small spring applies tension to hold an element in the correct position within the appliance, helping maintain reliable contact and stable operation. Replacing a worn spring can restore proper element support and performance.

• Provides push tension to keep the element seated and secure
• Helps prevent intermittent heating due to poor element contact
• Common signs include rattling, poor element stability, or intermittent heat

• Disconnect power and allow the unit to cool before service
• Access the element mounting area; note original spring placement
• Use needle-nose pliers to remove and install the spring carefully
• Inspect adjacent clips and wiring; replace damaged parts as needed

This spacer maintains the designed clearance between parts in your appliance, keeping components aligned for smooth, quiet operation. Replacing a worn or missing spacer helps prevent rubbing, binding, and premature wear in the affected assembly.

• Maintains the correct gap and alignment within the assembly
• Reduces friction, noise, and wear between adjacent parts
• Helps components seat and move smoothly as designed
• Typical symptoms include scraping noises, looseness or wobble, misalignment, or visible spacer damage

• Disconnect power (and water supply, if applicable) before servicing
• Refer to your model's parts diagram to determine the spacer's location, orientation, and stack order
• Reuse existing hardware (washers, clips, screws) as required by your model
• Tighten fasteners snugly without deforming the spacer; verify smooth movement before full reassembly

This backsplash restores the rear trim behind a range or cooktop, protecting the wall and covering wiring openings for a clean, factory-look finish. It replaces a damaged, dented, or missing backsplash to improve safety and appearance. What it does:

• Covers the gap between the cooktop and the wall to block spills, splashes, and heat from reaching the wall surface
• Hides wiring and mounting holes for a neat, finished look
• Replaces bent, cracked, or corroded rear trim that can collect grease and grime
• Helps maintain proper clearance and original appearance of the appliance

• One single-piece backsplash

• Basic hardware and mounting locations are OEM-specific; confirm matching fasteners on arrival
• Turn off power to the appliance and move the unit away from the wall before removing or installing the backsplash
• Use care to avoid scratching the finish during installation; two people may be needed for larger ranges
• If mounting holes or brackets are damaged, replace those items before installing this backsplash

This replacement surface heating element restores direct heat to a cooktop burner so pots and pans heat properly. It's a straightforward swap for a damaged or non-heating top burner coil. What it does:

• Heats cookware by providing the cooktop's surface heating element for the top burner
• Replaces elements that no longer glow, get intermittently hot, or fail to heat at all
• Restores even cooking when an old or damaged element causes uneven heating
• Works with controls and infinite switches that send power to the burner

• One surface heating (top burner) element

• Disconnect power to the range before attempting service to avoid shock hazard
• Allow the old element to cool completely before removal; handle the element by its base only
• Ensure the replacement is seated and connected to the terminal block securely before testing

Surface heating element that supplies a 700-watt top-burner heat source for compatible electric ranges, restoring reliable low-heat cooking and precise simmering performance on the affected burner. What it does:

• Provides 700W of heat for a small/simmer cooktop burner to support low- and medium-heat cooking.
• Replaces a burner element that won't heat, heats intermittently, or shows visible damage or burn marks.
• Restores normal burner operation so cookware heats more evenly on that zone.
• Fits into the existing cooktop receptacle and connects to the range wiring without additional heating components.

• Disconnect power at the circuit breaker or unplug the range before servicing.
• Allow the old element to cool fully before removal; handle terminals carefully to avoid bending.
• Inspect terminal clips and wiring for damage during installation; replace any damaged connectors or receptacles.

• Wattage: 700W
• Sold individually

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

20 pack. Safe on all glass and ceramic surfaces.

A self-tapping screw used to secure appliance panels and components, providing reliable fastening to sheet metal and plastic parts. Replaces worn or missing fasteners to restore proper fit and reduce rattling. What it does:

• Fastens panels, brackets, or trim to appliance frames and housings
• Creates its own threads in sheet metal or plastic for a secure hold
• Helps stop loose panels, vibration noise, and misaligned parts
• Commonly used where a short, durable fastener is needed

• Disconnect power and water before starting any repair
• Use the correct screwdriver or driver bit to avoid stripped heads
• Start threads carefully and avoid over-torquing to prevent damage
• Wear eye protection and gloves when working with sheet metal

This factory screw secures panels, brackets, or trim within your appliance. Replacing a missing or stripped fastener restores a tight fit, reduces vibration and rattles, and helps keep components aligned for reliable, long-term performance.

• Fastens panels, brackets, or trim to the appliance cabinet/frame
• Replaces damaged, rusted, or missing hardware
• Helps eliminate vibration noises, gaps, and loose-fitting parts
• Supports proper alignment of adjoining components

• Disconnect power; turn off gas/water supplies where applicable.
• Match to the original screw from your model's parts diagram before installation.
• Start threads by hand to avoid cross-threading; use the correct driver bit for the head.
• Tighten snugly—do not overtighten to prevent stripping threads or cracking plastic bosses.

This anchor tip secures the washer agitator to the transmission shaft so the agitator turns with the washer drive. Replaces a worn or damaged anchor tip to restore proper agitator engagement and reduce slipping. What it does:

• Secures the agitator to the drive shaft so the agitator rotates with the motor
• Helps prevent the agitator from slipping or spinning independently
• Commonly used when the agitator feels loose, makes grinding or clicking noises, or stops agitating
• Simple, low-profile part that works behind the agitator cap

• One anchor tip

• Disconnect power and water before starting any repair
• Remove agitator/agitator cap to access and replace the anchor tip per OEM instructions
• Inspect mating surfaces and replace any additional worn components if engagement remains poor

This rail base provides the structural support for the refrigerator drawer/rail assembly, restoring smooth drawer alignment and preventing sagging or binding. It's a direct-fit replacement that helps maintain proper drawer operation and cabinet fit. What it does:

• Supports and aligns the drawer/rail assembly so drawers slide smoothly
• Secures the lower rail to the cabinet to prevent shifting or sagging
• Restores proper drawer clearance and prevents sticking or uneven movement
• Addresses symptoms like crooked or loose drawers, binding, or gaps at the drawer edge

• One rail base

• Disconnect power to the appliance before beginning work
• Remove drawer(s) and any trim panels to access the rail area
• Use basic hand tools; avoid overtightening fasteners to prevent damage

This handle standoff spacer positions and secures a refrigerator/freezer door handle, keeping the handle correctly spaced from the door for smooth operation and a finished appearance. It's a small replacement part that restores proper handle fit. What it does:

• Creates a stable gap between the handle and the door so the handle mounts flush and operates without binding
• Keeps the handle aligned to prevent wobbling or loosening over time
• Restores original handle clearance after wear or damage to the existing spacer
• Useful when a broken, cracked, or missing spacer causes handle play or misalignment

• One handle standoff spacer

• Turn off power to any powered appliance components and remove items from the door or work area before starting
• Typical installation requires removing the handle fasteners, replacing the spacer, then reinstalling and torquing fasteners evenly
• Use appropriate hand tools and avoid over-tightening fasteners to prevent cracking the spacer

This outer door trim restores the finished appearance of an appliance door and covers the edge gap between the door panel and console for a clean, factory look. It helps protect the door edge from everyday wear. What it does:

• Covers and finishes the outer edge of the appliance door for a seamless appearance
• Helps prevent dirt and moisture from collecting at the door edge
• Restores cosmetic damage like scratches, dings or missing trim pieces
• Useful when replacing a cracked, warped or broken door trim piece

• High-level replacement only; remove and reinstall the outer door panel to access the trim
• Use appropriate screwdrivers and keep fasteners organized for reassembly
• Disconnect power (or gas) and follow manufacturer's safety steps before beginning service
• If trim is clipped in, carefully release retaining clips to avoid breaking adjacent parts

Comes with three connectors per package.

This door trim is the front-facing decorative bezel that restores the finish and edge protection to your appliance door. It replaces a worn, cracked, or damaged trim to improve appearance and help seal the door edge. What it does

• Replaces damaged or cracked door bezel to restore appearance
• Covers and protects the door edge from impacts and wear
• Helps maintain a clean seal line by securing the door edge trim
• Common symptom: visible cracks, chips, or loose trim along the door perimeter

• One door trim piece as shown

• Disconnect power to the appliance before beginning any service
• Use appropriate tools and keep fasteners for reassembly; handle trim carefully to avoid damage

This replacement screw secures appliance panels and components to keep parts aligned and stable. Use it to replace missing or damaged fasteners that cause loose trim, rattling, or unsecured panels for safer, quieter operation. What it does:

• Fastens panels, brackets, trim pieces, or small components in place
• Restores proper alignment and stops vibration or rattling caused by loose hardware
• Replaces stripped, corroded, or missing screws to prevent parts from shifting or falling
• Compatible where the OEM lists part W11244557 as the required fastener

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten securely but avoid over-tightening, which can strip threads or crack parts
• Replace like-for-like; length before installing