Wfe361lvso Parts

This spacer provides a precise gap for proper alignment and clearance between components, helping maintain correct part positioning for reliable operation. It's a simple replacement that restores intended spacing and reduces wear. What it does:

• Positions and separates adjoining parts to maintain correct clearance
• Helps prevent rubbing, misalignment, or binding of moving components
• Restores factory spacing after maintenance or part replacement
• Fits where the original spacer was used to support assembly alignment

• One spacer as shown

• Inspect surrounding components and mounting surfaces for damage before installing
• Remove power to the appliance and follow manufacturer service instructions
• Install in the same orientation as the original spacer and verify proper clearance
• If fasteners or adjacent parts are worn, replace them to ensure a secure fit

This oven rack is a replacement wire rack that restores stable support for cookware and bakeware, letting trays and pans slide in and out smoothly. It fits into the oven's rack supports to provide even cooking placement. What it does:

• Provides a stable shelf for baking sheets, pans, and cookware inside the oven
• Slides on oven rack supports to position food closer or farther from heat
• Replaces bent, warped, or missing racks that prevent stable placement
• Helps maintain even airflow and cooking clearance by restoring proper rack height

• One replacement oven rack

• Install by sliding rack into the oven's existing rack supports until fully seated
• No special tools required; handle edges carefully to avoid pinching
• Remove racks before using self-clean cycle; allow oven to fully cool before handling
• Use oven mitts or gloves when inserting/removing while hot

This replacement drawer panel restores the exterior trim and alignment of a refrigerator/freezer drawer for a clean, finished look. It replaces damaged or worn panels to help the drawer close and operate as intended. What it does:

• Replaces cracked, dented, scratched or discolored drawer front trim
• Restores proper front alignment and helps ensure the drawer closes smoothly
• Provides the cosmetic finish that matches the appliance's lower drawer
• Secures to the drawer assembly using existing fasteners and mounting points

• Disconnect power to the appliance before beginning work
• Remove the drawer assembly to access mounting screws and clips as needed
• Keep original fasteners and trim pieces; transfer them to the new panel unless replacements are supplied

Color: White  Note: Right side endcap

This control panel assembly replaces a damaged or worn console to restore the user interface and housing for your appliance's controls. It provides the outer console, buttons and trim needed for normal control access and appearance. What it does:

• Provides the console housing and control button area used to operate the appliance
• Replaces cracked, faded, scratched or broken console surfaces and trim
• Restores button/trim alignment and the physical interface for selector knobs and switches
• Helps address issues caused by physical damage to the console

• Disconnect power to the appliance before starting any repair
• Handle the panel carefully to avoid scratching or damaging painted surfaces and lens areas
• Installation typically requires basic hand tools; follow the appliance service manual for proper disassembly/reassembly
• If the appliance has electronic control failures, this part replaces the console housing and user interface components only

Color: White. Size: 1 qt. can. Acrylic appliance paint.

Color: White  Note: Left side endcap

The INSULATION is an OEM component specifically designed for Whirlpool electric ranges. Positioned between inner and outer wall cavities, it efficiently buffers heat.

Fiberglass batting material keeps internal temperatures elevated for cooking while preventing harmful temperatures from spreading outside. Stable temperature control is essential for consistent results.   

Causes of damaged insulation could be high heat exposure over time weakening fibers, moisture ingress deteriorating integrity, or physical punctures allowing heat leakage.

Symptoms of insufficient insulation include: 

• Oven unable to effectively retain or distribute set temperatures
• Door and exterior surfaces becoming too warm to safely touch 
• Higher energy bills from frequent recovery heating cycles

This Whirlpool insulation is also compatible with electric ranges by GE, Frigidaire, Samsung, and some LG kitchen models.

The Insulation is an OEM part compatible with Whirlpool ranges. It is made of thick fiberglass material installed behind oven and broiler walls. The insulation works to contain heat within the oven cavity and prevent it from transferring to external surfaces, keeping panels cool for safety. 

Symptoms of damaged insulation include:

• Outer range surfaces getting excessively hot during baking  
• Inefficient or improper heating of oven or broiler elements
• Potential energy efficiency and component longevity issues

Causes of damage can be deterioration of the fiberglass over time, punctures or compressing of material from cleaning or repairs.  

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This support bracket secures and stabilizes appliance components to reduce movement and maintain proper alignment. A simple replacement that helps stop rattling and supports panels or assemblies so the appliance operates quietly and reliably. What it does

• Provides a stable mounting point to hold panels, housings or internal assemblies in place
• Restores proper alignment to reduce vibration, noise, and rubbing against adjacent parts
• Prevents sagging or movement that can lead to wear on connected components
• Useful when a bent, cracked or missing bracket causes loose panels or intermittent contact

• Turn off power to the appliance and unplug before starting work
• Use appropriate tools and retain all fasteners; replace any damaged clips or screws
• Compare the bracket to the original to confirm orientation and fit before final installation