Wfg710h0as Parts

The HOLDER-ORFICE is an OEM component specifically designed for Whirlpool brand gas ranges and cooktops. It serves as the mounting bracket that secures the gas orifice fitting in the proper position. Correct orifice placement is critical for targeted gas flow and optimal flame adjustment.

Symptoms of a bad holder-orifice include: 

• Flames that cannot be properly adjusted and controlled from high to low 
• Potential safety hazards such as gas leaks due to a loose fitting
• Inefficient or uneven heating from erratic gas flow issues

Causes of failure include normal wear over time exposed to heat and vibration, or damage from accidental impact that warps the holder.

This OEM Whirlpool replacement ensures the orifice fitting remains firmly in position. Compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, and select Kenmore models. Replace your holder orifice today for safe, dependable gas range functionality.

This electronic control board manages the oven/range functions and user controls so the appliance responds to button presses and follows programmed bake/ignite cycles. Replaces a failed control board to restore normal control and timing functions. What it does:

• Receives input from the console and operates bake/broil/ignition sequences
• Controls timers, display readouts, and user-command processing
• Can cause blank display, unresponsive touchpad/buttons, or failure to start heating/ignite when faulty
• Re-establishes proper control logic and signal routing when replaced

• Disconnect power and turn off gas supply before starting any repairs
• Handle the board by the edges and avoid static discharge; wear an ESD strap if available
• Reassemble panels and restore power/gas only after connections are secure; test all functions per the service manual

The Insulation is an OEM part for Whirlpool ranges. It serves as the heat-resistant fiberglass insulation installed inside oven cavity walls and behind backsplash panels. 

Symptoms of damaged or degraded insulation could include:

• Uneven or inefficient heat distribution inside the oven 
• Hot and cold spots developing on bake elements over time
• Longer preheat periods are needed to reach target temperatures
• Higher energy costs from overworked heating components  

Causes may involve breaks in insulation fibers from extended heat cycling. Exposure to moisture or condensation could compromise insulation integrity as well. Physical punctures may develop from accidental impact or installing range components.

This replacement insulation works for Jenn-Air, KitchenAid, and select Kenmore oven ranges too. 

This front mounting bracket secures the appliance's front panel and helps keep the cabinet and components aligned for stable operation. A direct-fit replacement that restores proper panel fit and reduces vibration or rattling. What it does

• Secures the front panel or trim to the cabinet to maintain alignment and prevent gaps.
• Keeps adjacent components from shifting, helping reduce vibration and noise.
• Commonly replaces cracked, bent, or missing brackets that cause loose or misaligned panels.
• Helps restore correct door/panel fit and smooth operation of attached controls or trim.

• One front mounting bracket

• Disconnect power (and water if applicable) before starting any repair.
• Access may require removing the front panel or trim—keep screws and fasteners organized.
• Inspect mating surfaces and existing fasteners; replace any damaged screws or clips.

This orifice holder assembly secures the gas orifice for a surface burner, positioning it for proper gas flow and consistent ignition. Replacing a damaged holder helps restore stable flame performance and safe burner operation. What it does:

• Holds and aligns the burner orifice to direct gas into the burner tube
• Maintains correct spacing for reliable ignition and even flame
• Helps prevent gas leaks caused by cracked, bent, or loose holders
• Reduces symptoms like weak or uneven flames, delayed ignition, or burner misfiring

• Turn off gas supply and electrical power before inspecting or replacing the part
• Tighten fasteners securely but avoid overtightening; replace any damaged gaskets or seals
• After installation, check all gas connections for leaks with a soap solution or approved detector

This heat shield protects oven or range components from direct heat, helping prevent damage to nearby panels and wiring. It's a direct-replacement exterior shield used when existing metal shields are warped, cracked, or missing. What it does:

• Diverts and dissipates heat away from control panels, insulation, or adjacent components
• Helps stop heat-related discoloration, warping, or premature wear of nearby parts
• Restores proper clearance and airflow around the oven cavity after shield damage
• Commonly replaced when you see scorched areas, melted trim, or gaps where a shield once sat

• One heat shield (exact shape and mounting holes as shown in OEM diagram)

• Disconnect electrical power (and gas, if applicable) before starting any repair
• Remove oven racks and any trim panels to access the shield; keep track of fasteners
• Compare the replacement to the removed part to confirm fit before fastening
• If mounting hardware is damaged or missing, procure correct OEM fasteners — only the shield is guaranteed to ship

This mounting bracket secures internal or external appliance components to the cabinet, restoring proper alignment and preventing vibration. It's a small but critical metal support used where fasteners attach panels or assemblies. What it does:

• Provides a secure attachment point for panels, controls, or assemblies
• Prevents loosening, rattling, and misalignment caused by broken or missing supports
• Restores proper fit and function when original bracket is bent, cracked, or missing
• Works as a direct replacement using existing fasteners and mounting holes

• Disconnect power (and gas if applicable) before beginning any repair
• Installation typically requires basic hand tools (screwdriver, nut driver, or socket)
• Retain or reuse original screws; verify bracket orientation before tightening
• If metal edges are sharp, use care and protective gloves to avoid cuts