Wfl 2060/Wfr Parts

This electrical door lock assembly secures the appliance door during cycles so the machine can run safely and reliably. It replaces a failed lock to restore proper door latching and allow normal operation. What it does:

• Electrically latches the door during start and while a cycle runs
• Prevents the door from opening mid-cycle for safety and wash integrity
• Common symptom: dishwasher won't start, shows a door or lock error, or door won't stay closed

• One electrical door lock assembly

• Disconnect power before beginning work to avoid shock or injury
• Remove door access panels or inner door trim as required for access
• Handle latch and surrounding trim carefully to avoid damage to the door or wiring
• Test door operation and run a short cycle after installation

The Drain Pump is an OEM part for Bosch washing machines. This pump works to remove water from the washer tub at the end of each cycle, preventing excessive moisture buildup.

Causes of drain pump failure can include blockages in the pump or drainage system that restrict water flow, wearing of internal pump components, or the motor bearing seizing up over time.

Symptoms of a bad drain pump include:

• The washer failing to complete drain cycles fully
• Excessive water remaining in the tub after cycles
• Strange noises or vibrations coming from the pump area
• Drain hoses not properly emptying or gurgling

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This flexible drain hose routes wastewater from the dishwasher tub to the drain pump or household drain, helping remove used water after a cycle. It replaces a damaged or leaking hose to restore proper draining. What it does

• Carries wastewater from the dishwasher to the drain pump or disposal
• Stops leaks and prevents water pooling when the original hose is cracked or split
• Helps resolve slow or incomplete draining caused by a compromised hose
• Fits the factory hose connections and follows the cabinet routing to avoid kinks

• One flexible drain hose

• Disconnect power and turn off water before beginning any repair
• Remove the lower access panel or toe kick to reach hose connections
• Inspect and follow the original routing; avoid sharp bends or kinks that restrict flow
• Secure hose with appropriate clamps and check all connections for leaks after testing

This nozzle directs and focuses water flow inside the dishwasher so dishes get a thorough rinse. Replaces a worn, cracked, or clogged nozzle to restore spray coverage and help prevent poor cleaning performance. What it does

• Channels water from the spray arm or manifold to create a targeted spray pattern
• Helps maintain even water distribution across racks for better cleaning
• Clogs, cracks, or damage can cause weak spray or spotty wash results
• Compatible with systems that use a snap- or press-fit nozzle on the spray assembly

• Disconnect power and water supply before starting any repair
• Remove the spray arm or access panel as needed to reach the nozzle
• Inspect mating surfaces for debris; press or snap the new nozzle into place until seated

This tub clamp secures a flexible seal or hose to the appliance's tub, maintaining a tight, leak-resistant connection. Replace a weakened or damaged clamp to stop leaks and keep the tub joint stable during operation.

• Applies even clamping pressure around the tub connection
• Helps prevent water leaks at the tub-to-seal or tub-to-hose joint
• Restores proper fit when the original clamp is stretched, stripped, corroded, or missing
• Common symptoms: water at the base/front, loose seal or hose, visible clamp damage

• Disconnect power and turn off water before service
• Access the tub connection; remove the old clamp and inspect the seal/hose for wear
• Clean mating surfaces; seat the seal evenly, position the clamp, and tighten until snug without pinching the rubber
• Run a quick fill/drain test and check for leaks

A U-bend retainer designed to secure a U-shaped heating element or tubing in place, preventing movement and vibration for reliable operation. Fits as the replacement hold-down clip used on compatible Whirlpool HVAC and appliance assemblies. What it does:

• Secures U-shaped element or tubing to the appliance frame or mounting bracket
• Prevents rubbing or vibration that can lead to wear or noisy operation
• Helps maintain proper spacing and alignment of the element for consistent performance
• Used where a compact, U-shaped clamp is required to hold components safely

• One U-bend retainer clip as shown

• Inspect the surrounding area and replaced part for damage before installing
• Use basic hand tools; align clip over the U-bend and fasten to the designated mounting point
• Disconnect power and allow components to cool before attempting repair
• Replace with the exact OEM fasteners

This front drum motor mounting bushing supports the dryer drum shaft and helps the drum spin smoothly for quiet, even drying. It replaces a worn bearing surface to reduce noise and prevent drum misalignment. What it does:

• Provides a low-friction bearing surface for the drum shaft at the front motor mount
• Helps keep the drum properly aligned during rotation
• Reduces squealing, grinding, or rubbing noises caused by a worn front bushing
• Prevents excess wear on the drum shaft and adjacent components when functioning correctly

• One front drum motor mounting bushing

• Disconnect power before beginning any repair and follow all safety precautions
• Inspect the drum shaft, drum seal, and rear bushing for wear and replace as needed
• Use appropriate tools to remove the old bushing and press or seat the new bushing evenly
• Re-check installation and related components if alignment or noise persists after replacement

This stator is the stationary motor component that creates the magnetic field needed for the washer's drive motor to operate. It restores motor function so the appliance can agitate and spin normally. What it does:

• Generates the magnetic field that interacts with the rotor to drive the motor.
• Enables proper agitation and spinning when the motor and rotor are functioning.
• Commonly replaced when motor runs poorly, makes unusual noises, or the washer fails to spin.
• Works as part of the motor assembly to maintain consistent motor performance.

• One stator

• Disconnect power and water supply before beginning any repair.
• Access typically requires removing the washer cabinet or motor housing; follow the service manual for your model.
• Inspect the rotor/motor and wiring for damage when replacing the stator.

This genuine mounting screw secures panels and components so assemblies stay aligned and rattle-free. Designed to replace worn or missing fasteners and restore proper fit and function. What it does:

• Secures panels, brackets or trim to prevent movement and vibration
• Restores proper alignment of assemblies that feel loose or shift
• Helps eliminate rattling, squeaks, or parts that fall away during use
• Matches OEM thread and head type for correct fit

• Use the matching screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten which can strip threads or crack plastic
• Replace any additional damaged or missing fasteners for best results
• Disconnect power or follow appliance-specific safety steps before working near wiring or energized components

This transport cover secures internal components during shipping and service to prevent movement and damage. It helps keep parts aligned and reduces noise caused by loose components while the appliance is being moved. What it does:

• Holds internal components in place during transport to prevent shifting or impact damage
• Reduces rattles and vibration caused by unsecured parts
• Protects delicate assemblies from knocks during delivery or handling
• Helps maintain alignment of components until the appliance is installed

• One transport cover

• Disconnect power and water before servicing the appliance
• Remove all shipping brackets and covers per the owner's manual before normal operation
• Use manufacturer-specified fasteners and torque; do not force or modify the part

The Hose Clamp is an OEM part for Bosch washers. This clamp secures connecting hoses to direct water flow where needed.

Causes of a bad hose clamp can be wear and tear over time, accidental damage from maintenance or repairs, or degradation of the clamp material from chemical exposure.

Symptoms of a bad hose clamp include:

• Leaks around hose connections
• Loose or detached hoses
• Disrupted water flow impacting cleaning performance

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

2 included - Front load

This adjustable leveling foot provides a stable, height-adjustable support for appliances, helping restore proper alignment and reduce rocking. It replaces worn or damaged feet to keep the appliance level and secure on uneven floors. What it does

• Supports and stabilizes the appliance by allowing height adjustment
• Helps eliminate rocking, tipping, or uneven gaps caused by a damaged or missing foot
• Restores proper appliance alignment for smooth door operation and even performance
• Designed for use where the OEM lists a removable/replaceable foot component

• One adjustable leveling foot

• Inspect mounting location and hardware; replace any damaged clips or screws before installing
• Hand-start threads, then tighten with appropriate tool until secure; avoid overtightening
• Unplug or disconnect power before service if reaching into the cabinet or near wiring

This holder is a replacement mounting bracket that secures a small internal component in place to restore proper alignment and support. It helps keep parts stable so the appliance operates as intended. What it does

• Secures and supports an internal component to prevent movement or misalignment
• Replaces cracked, broken, or worn mounting points that allow rattling or improper part position
• Restores stable contact where a loose component causes intermittent operation or noise
• Fits a specific OEM location; use the part number to confirm exact application

• One replacement holder/mounting bracket

• Disconnect power and water before starting any repairs
• Inspect surrounding clips or fasteners and reuse or replace as needed—this part typically snaps or screws into place
• Handle plastic mounting parts gently to avoid cracking during installation