Wfl2060nuc 86/I Parts

This drain reservoir is the dishwasher plumbing housing that collects and directs wastewater to the drain pump, helping prevent internal leaks and ensuring proper draining. Replace a cracked or clogged reservoir to restore reliable water flow and reduce water under the unit. What it does:

• Funnels wastewater from the tub to the drain pump so the machine can evacuate used water
• Helps contain minor spills and prevents water from reaching sensitive electronics
• Works with the drain pump and hoses to maintain proper drainage
• Commonly causes water pooling under the dishwasher, slow or no drain cycles, or visible leaks when damaged

• Disconnect power to the appliance before starting any repair
• Shut off water supply and remove lower access panels or kickplate as needed
• Handle with care to avoid damaging adjacent hoses, clips, or wiring; replace any worn seals

This dispenser door is the outer cover for the dishwasher detergent cup, providing a secure compartment for powder or tablet detergent until the wash cycle releases it. Restores proper detergent release and keeps the cup sealed during fill and wash. What it does:

• Covers and seals the detergent cup so detergent stays dry until the cycle releases it
• Pops open at the correct time so detergent dispenses into the wash
• Replaces cracked, warped, or otherwise damaged doors that won't latch or open
• Helps prevent detergent from dissolving prematurely or leaking into the tub

• Disconnect power and water to the appliance before servicing
• Remove the inner door panel or access the dispenser per the service manual to replace the door
• Handle plastic parts carefully to avoid damage; use proper hand and eye protection

This replacement hose-pressure chamber routes water to the dishwasher's pressure chamber so the machine can sense and control water level. Restores proper pressure sensing to help prevent overfilling and fill errors. What it does

• Connects the sump/water path to the pressure chamber so the water-level sensor can detect fill height.
• Replaces cracked, pinched, or collapsed hose that can cause inaccurate water-level readings.
• Commonly used when dishwasher shows overfill, won't fill correctly, or reports water-level or pressure-related errors.
• Flexible vinyl tubing designed for routing in tight spaces without kinking.

• Disconnect power and shut off the water supply before starting any repair.
• Inspect nearby fittings and the pressure chamber for wear; replace clamps if damaged.
• Push-fit or clamp the hose securely to both ports; ensure there are no kinks or sharp bends.

This interference capacitor suppresses electrical noise and radio-frequency interference to help the appliance's electronics run more reliably. It fits on the control board and supports stable operation by filtering stray voltage spikes. What it does:

• Filters electrical and radio-frequency interference that can cause erratic control behavior or false error codes
• Reduces electrical noise that can affect nearby audio or radio reception
• Helps protect control circuitry from transient voltage spikes
• Commonly used when appliance exhibits intermittent faults or unexplained control glitches

• Disconnect power to the appliance before starting any repair
• Discharge capacitors and avoid touching leads; use insulated tools and follow safe-handling practices
• Replace only with the exact part specified for your model and secure all wire connections firmly

This spin speed knob lets you select wash spin settings so you can adjust water extraction for different loads. It replaces a worn, cracked, or loose dial to restore clear speed selection and smooth control. What it does:

• Selects the washer's spin speed setting for proper water extraction
• Restores firm, accurate dial operation when original knob is loose or broken
• Helps prevent accidental speed changes during a cycle
• Matches OEM fit and detent locations for correct alignment

• Remove power from the appliance before attempting replacement
• Typically pulls off the control shaft; inspect for retaining clip or set screw
• If knob does not seat fully, verify shaft and index tab are undamaged

This wire harness connects the dryer drum drive motor to the appliance wiring, restoring reliable electrical connections so the drum can receive power and operate as intended. Fits specific Bosch drum drive assemblies. What it does:

• Routes and secures electrical connections between the drive motor and main wiring harness
• Restores power delivery to the drum drive motor when the original harness is damaged
• Helps resolve symptoms such as the drum not turning or intermittent motor operation
• Prevents loose or corroded connections that can cause arcing or failure

• Disconnect power at the breaker or unplug the appliance before servicing
• Use basic hand tools; avoid pinching or stretching the harness during installation
• After install, reconnect power and run a test cycle to confirm proper drum operation

This window frame is the door trim piece that holds and secures the viewing glass, restoring the door's fit and finished appearance. Use it to replace a cracked, warped, or missing frame so the door closes and looks correct. What it does:

• Secures the viewing glass in the appliance door and maintains a flush exterior finish
• Helps keep the glass aligned so the door seals and closes properly
• Restores the door's cosmetic appearance when the original frame is cracked, dented, or worn
• Provides the structural support needed around the window opening to prevent rattling or movement

• Disconnect power and follow manufacturer safety guidelines before starting any repair
• Handle glass carefully; wear gloves and eye protection to avoid cuts
• Require removing the door panel and a few screws or clips—retain original fasteners unless replacements are provided

This base panel replaces the lower access panel on compatible dishwashers, covering and protecting the unit's underside and internal components while maintaining a finished appearance at the appliance base. What it does:

• Covers the dishwasher's lower cabinet area to protect internal components from debris and accidental contact
• Provides the finished exterior look at the appliance base
• Helps keep access points secure for proper routing of drain and wiring assemblies
• Matches OEM fit and attachment locations for a straightforward replacement

• Disconnect power and shut off the water supply before starting
• Remove the toe kick or lower access screws to access and remove the old panel
• Align mounting tabs and secure with the original screws; retain all fasteners
• Handle edges carefully to avoid scratches; before restoring power

This T-shaped water hose connector routes incoming water to separate internal hose lines, restoring proper water distribution inside the appliance. It replaces a worn or cracked hose tee to stop leaks and restore flow to internal components. What it does:

• Joins three water lines so water can be directed to multiple internal points
• Stops leaks caused by cracked or damaged tee fittings at hose junctions
• Restores reliable water flow to downstream parts that depend on the split connection
• Prevents hoses from separating at a failing junction

• Turn off and disconnect the appliance from the water supply before servicing
• Inspect hose ends and clamps; replace clamps or seals if worn
• Push hoses fully onto each barb and secure with appropriate clamps
• After installation, restore water and check all connections for leaks