Wfl2060uc /01 Parts

This dispenser door is the outer cover for the dishwasher detergent cup, providing a secure compartment for powder or tablet detergent until the wash cycle releases it. Restores proper detergent release and keeps the cup sealed during fill and wash. What it does:

• Covers and seals the detergent cup so detergent stays dry until the cycle releases it
• Pops open at the correct time so detergent dispenses into the wash
• Replaces cracked, warped, or otherwise damaged doors that won't latch or open
• Helps prevent detergent from dissolving prematurely or leaking into the tub

• Disconnect power and water to the appliance before servicing
• Remove the inner door panel or access the dispenser per the service manual to replace the door
• Handle plastic parts carefully to avoid damage; use proper hand and eye protection

This replacement hose-pressure chamber routes water to the dishwasher's pressure chamber so the machine can sense and control water level. Restores proper pressure sensing to help prevent overfilling and fill errors. What it does

• Connects the sump/water path to the pressure chamber so the water-level sensor can detect fill height.
• Replaces cracked, pinched, or collapsed hose that can cause inaccurate water-level readings.
• Commonly used when dishwasher shows overfill, won't fill correctly, or reports water-level or pressure-related errors.
• Flexible vinyl tubing designed for routing in tight spaces without kinking.

• Disconnect power and shut off the water supply before starting any repair.
• Inspect nearby fittings and the pressure chamber for wear; replace clamps if damaged.
• Push-fit or clamp the hose securely to both ports; ensure there are no kinks or sharp bends.

This spin speed knob lets you select wash spin settings so you can adjust water extraction for different loads. It replaces a worn, cracked, or loose dial to restore clear speed selection and smooth control. What it does:

• Selects the washer's spin speed setting for proper water extraction
• Restores firm, accurate dial operation when original knob is loose or broken
• Helps prevent accidental speed changes during a cycle
• Matches OEM fit and detent locations for correct alignment

• Remove power from the appliance before attempting replacement
• Typically pulls off the control shaft; inspect for retaining clip or set screw
• If knob does not seat fully, verify shaft and index tab are undamaged

This wire harness connects the dryer drum drive motor to the appliance wiring, restoring reliable electrical connections so the drum can receive power and operate as intended. Fits specific Bosch drum drive assemblies. What it does:

• Routes and secures electrical connections between the drive motor and main wiring harness
• Restores power delivery to the drum drive motor when the original harness is damaged
• Helps resolve symptoms such as the drum not turning or intermittent motor operation
• Prevents loose or corroded connections that can cause arcing or failure

• Disconnect power at the breaker or unplug the appliance before servicing
• Use basic hand tools; avoid pinching or stretching the harness during installation
• After install, reconnect power and run a test cycle to confirm proper drum operation

This base panel replaces the lower access panel on compatible dishwashers, covering and protecting the unit's underside and internal components while maintaining a finished appearance at the appliance base. What it does:

• Covers the dishwasher's lower cabinet area to protect internal components from debris and accidental contact
• Provides the finished exterior look at the appliance base
• Helps keep access points secure for proper routing of drain and wiring assemblies
• Matches OEM fit and attachment locations for a straightforward replacement

• Disconnect power and shut off the water supply before starting
• Remove the toe kick or lower access screws to access and remove the old panel
• Align mounting tabs and secure with the original screws; retain all fasteners
• Handle edges carefully to avoid scratches; before restoring power

This T-shaped water hose connector routes incoming water to separate internal hose lines, restoring proper water distribution inside the appliance. It replaces a worn or cracked hose tee to stop leaks and restore flow to internal components. What it does:

• Joins three water lines so water can be directed to multiple internal points
• Stops leaks caused by cracked or damaged tee fittings at hose junctions
• Restores reliable water flow to downstream parts that depend on the split connection
• Prevents hoses from separating at a failing junction

• Turn off and disconnect the appliance from the water supply before servicing
• Inspect hose ends and clamps; replace clamps or seals if worn
• Push hoses fully onto each barb and secure with appropriate clamps
• After installation, restore water and check all connections for leaks

This wire harness connects and powers a dishwasher's dual water inlet valve, restoring reliable valve operation and proper water fill control. It replaces a damaged or burned harness to help stop intermittent fills or electrical faults. What it does:

• Routes power and signals to the cold-side and secondary inlet valve solenoids so the dishwasher can control water intake
• Replaces frayed, pinched, or heat-damaged wiring that can cause intermittent filling or valve failure
• Helps eliminate blown fuses, tripped breakers, or error codes related to inlet valve electrical faults
• Matches OEM connector plugs and wire colors for a direct electrical replacement

• One assembled wire harness for a dual water inlet valve

• Disconnect power and water supply before starting any repair; failure to disconnect power can cause shock
• Inspect connectors and mounting points for damage and secure harness away from heat or moving parts
• Ensure correct connector orientation; do not force connectors—verify full seating for proper electrical contact