Wfmc330suc/06 Parts

This hose inlet is the water inlet connection that directs incoming water into the appliance, restoring a secure supply path and helping prevent leaks at the entry point. What it does

• Provides the sealed connection point for the incoming water supply hose.
• Routes water into the appliance's fill system so cycles can start and run properly.
• Helps prevent leaks where the external supply hose attaches.
• Commonly replaced when water won't enter, the connection leaks, or the inlet is damaged.

• One hose inlet connection.

• Turn off the water supply and disconnect power before replacing.
• Inspect existing seals or gaskets; replace if cracked or worn.
• Tighten connections to hand-firm plus a quarter turn; avoid overtightening.
• After installation, restore water and power and check thoroughly for leaks during a fill cycle.

Spring tank secures and positions an appliance tension spring to maintain proper movement and balance for a door or other moving assembly. Replacing a worn or broken tank restores correct spring alignment and smoother, more reliable operation. What it does:

• Holds the end of the tension spring and keeps it aligned in the assembly.
• Maintains correct spring tension so doors or panels open, close and remain balanced.
• Prevents spring detachment that can cause sudden drops, misalignment or noisy operation.
• Common symptoms of a failing tank: door drops or won't stay open, uneven closing, rattling or banging during movement.

• Disconnect power to the appliance before starting any repair to avoid electrical hazards.
• Support the door or moving panel while replacing the tank to prevent sudden movement or injury.
• Use the OEM part orientation and hardware; inspect the spring and mounting points for wear and replace if scored or damaged.
• Test the door/panel operation several times after installation to ensure correct tension and secure mounting.

This rear drum motor mounting bushing supports the motor shaft at the back of the tub, keeping the drum aligned and reducing wear. It restores smooth drum rotation and helps reduce noise and vibration when functioning properly. What it does:

• Centers and supports the motor shaft to maintain proper drum alignment.
• Cushions rotating components to reduce squealing, grinding, or scraping noises.
• Helps prevent excess drum wobble and uneven wear on the tub and bearings.
• Can stop intermittent rubbing or burning smells caused by a worn mounting surface.

• Disconnect power before starting and follow all safety precautions; service panels may have sharp edges.
• Access typically requires removing the dryer/heater assembly and drum.
• Inspect mating surfaces and surrounding components (shaft, bearing, seal). Replace any excessively worn parts to prevent repeat failures.
• Use only OEM-recommended parts and fasteners; do not force or press the part in without proper alignment.

This replacement hose connects the dishwasher drain/sump to the drain system, restoring proper water removal and preventing leaks or standing water. It's a direct-fit service part when the original hose is cracked or clogged. What it does

• Carries waste water from the dishwasher sump to the household drain or disposal
• Restores proper draining when a split, collapsed, or clogged hose causes standing water
• Helps stop leaks and puddling that can occur from worn or damaged hose sections
• Maintains correct flow to prevent dishwasher error codes related to drainage

• Turn off power and water supply to the appliance before starting any repair
• Inspect hose routing and clamps; replace any damaged clamps or retainers for a secure seal
• Ensure hose connections are tight and routed without kinks to allow proper drainage

This NTC temperature sensor (thermistor) detects temperature changes and sends a signal to the appliance control so temperature is monitored and regulated accurately. It's a direct-replacement sensing element for temperature-feedback systems. What it does

• Measures temperature and converts it to a resistance signal the control board reads
• Commonly used for temperature regulation and safety control in appliance cycles
• Faulty sensor may cause incorrect temperature readings, erratic cycle behavior, or temperature-related error codes
• Restores accurate temperature feedback when replaced

• One NTC temperature sensor (thermistor) assembly

• Intended for users comfortable with basic appliance repair; disconnect power before starting
• May require panel removal and careful handling of wiring connectors; note connector orientation before disconnecting
• Avoid touching the sensing tip with bare hands or bending the probe excessively