Wfmc640suc/02 Parts

The Analogue Pressure Switch is an OEM part for Bosch washing machines. It is part of the water fill system, used to monitor water pressures during inlet filling. The switch communicates pressure levels to the control module.

Causes can be worn contacts, mineral deposits obstructing function, or moisture damage over time.

Symptoms of a bad analogue pressure switch include:

• Inconsistent or inadequate water levels during fill cycles
• Error codes or faults related to water pressure readings
• The washer failing to fill or dispense water as needed

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This factory fastener secures appliance components and panels so they stay aligned and quiet. Replacing a missing, stripped, or corroded screw restores a tight fit and helps prevent vibration, rattling, and premature wear.

• Secures brackets, covers, panels, or internal parts per your model's design
• Helps maintain alignment and reduce vibration/noise during operation
• Replaces lost, stripped, rusted, or damaged hardware
• Common signs include loose or shifting panels, rattling sounds, or a missing screw found during service

• Disconnect power before servicing; shut off water or gas if applicable to your appliance
• Match the screw to the original location/length; replace one at a time to avoid mix-ups
• Start threads by hand to prevent cross-threading; tighten snugly without overtightening
• Use the correct driver for the head type on your model to avoid stripping

The Screw is an OEM part for Bosch microwave ovens. It is a component that secures the outer casing and front paneling of the microwave. The screw is designed to withstand repeated heating and cooling cycles without loosening or degrading. 

Symptoms of bad screw include:

- The front panel or outer casing becoming loose, detached, or misaligned
- Gaps appearing in the seams or joints of the microwave structure
- The door not sealing properly leading to leaks

Over many uses of the microwave, screws can wear down or strip out from over-tightening during repairs or installations. It is important to replace worn screws to ensure the microwave maintains an intact structure.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
 

This replacement mounting screw secures panels, brackets, and small assemblies to restore a snug fit and reduce rattling or loose parts. Ideal when a factory fastener is missing, damaged, or stripped. What it does:

• Fastens panels, trim pieces, brackets and internal assemblies.
• Restores proper alignment and prevents movement or vibration.
• Helps stop rattling, loose trim, or parts that shift during operation.
• Use when an original screw is missing, worn, or has a damaged head.

• Disconnect power (and water supply for water-connected appliances) before servicing.
• Use the correct screwdriver or bit to avoid stripping the head.
• Tighten until secure but avoid over-tightening which can strip threads or crack plastics.

This front drum motor mounting bushing supports the dryer drum shaft and helps the drum spin smoothly for quiet, even drying. It replaces a worn bearing surface to reduce noise and prevent drum misalignment. What it does:

• Provides a low-friction bearing surface for the drum shaft at the front motor mount
• Helps keep the drum properly aligned during rotation
• Reduces squealing, grinding, or rubbing noises caused by a worn front bushing
• Prevents excess wear on the drum shaft and adjacent components when functioning correctly

• One front drum motor mounting bushing

• Disconnect power before beginning any repair and follow all safety precautions
• Inspect the drum shaft, drum seal, and rear bushing for wear and replace as needed
• Use appropriate tools to remove the old bushing and press or seat the new bushing evenly
• Re-check installation and related components if alignment or noise persists after replacement

This NTC temperature sensor (thermistor) detects temperature changes and sends a signal to the appliance control so temperature is monitored and regulated accurately. It's a direct-replacement sensing element for temperature-feedback systems. What it does

• Measures temperature and converts it to a resistance signal the control board reads
• Commonly used for temperature regulation and safety control in appliance cycles
• Faulty sensor may cause incorrect temperature readings, erratic cycle behavior, or temperature-related error codes
• Restores accurate temperature feedback when replaced

• One NTC temperature sensor (thermistor) assembly

• Intended for users comfortable with basic appliance repair; disconnect power before starting
• May require panel removal and careful handling of wiring connectors; note connector orientation before disconnecting
• Avoid touching the sensing tip with bare hands or bending the probe excessively

Includes(1)Shipping Bolt,(1)washer,(1)sleeve

The Shipping Bolt is an OEM part for Bosch washing machines. This bolt is designed to secure the washer drum assembly during shipping to prevent excessive movement and potential damage.

Causes of a bad shipping bolt can include stripping, damage to the threads, or loss of the bolt entirely during shipment or installation.

Symptoms of a damaged or missing shipping bolt include:

• Excessive shaking or rattling noises from inside the washer drum
• The drum not rotating properly during wash cycles
• Reduced washing efficiency and improper washing performance

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Hose Clamp is an OEM part for Bosch washers. This clamp secures connecting hoses to direct water flow where needed.

Causes of a bad hose clamp can be wear and tear over time, accidental damage from maintenance or repairs, or degradation of the clamp material from chemical exposure.

Symptoms of a bad hose clamp include:

• Leaks around hose connections
• Loose or detached hoses
• Disrupted water flow impacting cleaning performance

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

2 included - Front load

This is a factory-style screw used to secure appliance panels and components for a reliable, low-profile hold. It replaces worn or missing fasteners to stop rattling and keep parts aligned during normal use. What it does:

• Secures trim, panels, brackets or small components in place
• Stops loose parts that can cause rattling or vibration noises
• Restores correct fit where a missing or damaged screw allows gaps
• Works as a direct replacement when the original fastener is lost or stripped

• One screw

• Disconnect power and water before servicing the appliance
• Start the screw by hand to avoid cross-threading; use the correct driver bit
• Tighten snugly but avoid over-torquing to prevent stripping or part damage
• Keep removed hardware organized to ensure correct reassembly

This interference capacitor reduces electrical noise and helps protect the appliance's control circuitry from voltage spikes. It's a direct-replacement noise suppressor used where EMI/RFI filtering is required for reliable operation. What it does:

• Suppresses electromagnetic and radio-frequency interference that can affect controls and electronics
• Helps prevent false signals or erratic behavior caused by electrical noise
• Supports stable operation of motors and electronic control boards
• Can reduce audible electrical noise or interference-related symptoms

• Disconnect power at the breaker before inspecting or replacing the capacitor
• Discharge the capacitor and avoid touching terminals; use insulated tools
• Verify wiring match and polarity before connecting