Wfw87hedwo Parts

Replacement bumper that cushions appliance parts and absorbs shock to prevent rubbing, rattling and surface damage. Restores proper fit and quieter operation for components that contact cabinets, doors or panels. What it does:

• Cushions contact points to reduce noise from doors, drawers or panels.
• Prevents metal-to-metal or metal-to-surface scraping that can cause wear or cosmetic damage.
• Helps components close and seat more evenly to reduce vibration and movement.
• Common symptom fixes: eliminates rattling, stops rubbing noises, and prevents chipping or scuffing where parts meet.

• One bumper.

• High-level, tool-light replacement; usually presses into or adheres to the mounting surface.
• Disconnect power or unplug the appliance before opening panels where required.
• Inspect surrounding clips/retainers and clean the mounting area for best adhesion or fit.

Size: 10-24 x 3/8 inch.

This genuine replacement power cord restores electrical connection to your appliance so it can safely receive power. It replaces a damaged or worn cord to help eliminate power loss and reduce electrical hazards. What it does:

• Provides the electrical connection between the appliance and your home's power supply
• Replaces frayed, cracked, or burned cord insulation and damaged plugs
• Helps stop intermittent power issues caused by a faulty cord or connector
• Restores safe, reliable power routing when the original cord is compromised

• Always disconnect power at the breaker or unplug the appliance before installing
• Follow the appliance wiring diagram and route the cord to avoid heat or pinch points
• Secure strain relief and connectors per the manufacturer's instructions

Push-in nut that secures panels, trim, or small components to studs or shafts. Restores a firm, vibration-resistant fastener to help stop loose panels and rattling caused by a worn or missing nut. What it does:

• Secures panels, trim or small assemblies to mounting studs or shafts.
• Helps keep parts aligned and reduces vibration or rattling during operation.
• Common symptom: loose or shifting panels, audible rattling, or components that won't stay in place.
• Designed for a push-fit installation to replace worn or missing fasteners.

• Always disconnect power to the appliance before servicing.
• Push the nut fully onto a clean, undamaged stud until seated; replace damaged studs or mounting hardware.
• If needed, use pliers or a socket to press the nut on evenly—avoid deforming surrounding plastic or sheet metal.

This inner door panel restores the washer lid's interior finish and structural support, helping the lid close and seal properly. It replaces a cracked, dented, or cosmetically damaged inner door to improve appearance and function. What it does:

• Provides the interior surface and mounting points for the washer top lid assembly
• Restores proper lid alignment and helps the lid close smoothly
• Eliminates sharp edges or cosmetic damage from a cracked or dented inner door
• Helps maintain correct fit with the outer door and lid components

• One inner door panel

• Disconnect power and water supply before starting any repair
• Remove the outer lid and related fasteners to access and replace the inner panel
• Keep track of screws and clips; hand-tighten fasteners to avoid stripping

This retainer is a small mounting clip that secures internal components in place to prevent shifting and noise during operation. It restores proper alignment so panels or assemblies stay fastened and stable. What it does

• Holds a panel, trim, or internal component securely in its mounting location
• Prevents rattling, vibration noise, and loose or sagging parts
• Keeps connected parts aligned for reliable operation
• Commonly replaced when clip is cracked, broken, or missing

• One retainer clip

• Disconnect power before starting any repair
• Remove necessary panels or access covers to reach the damaged clip
• Replace the clip in the same orientation; avoid forcing parts to prevent damage
• If additional fasteners are damaged or missing, replace them as needed for a secure installation

This top panel is the exterior upper cover that protects internal washer parts and gives the appliance a finished look. It restores a secure mounting surface for the control area and helps keep water and debris out of the cabinet. What it does

• Covers and protects internal components at the top of the washer cabinet.
• Provides the mounting surface and alignment for the control console and lid.
• Restores appearance when the original panel is dented, cracked, or rusted.
• Reduces rattles or vibration caused by a loose or warped top.

• Disconnect power and water supply before starting any repair.
• Use basic hand tools; some screws or clips may need to be removed to lift the old panel.
• Handle edges carefully — metal panels can be sharp.
• Have a second person assist if needed to prevent bending or dropping the panel.

This touch-up paint bottle restores small chips and scratches on painted appliance surfaces to improve appearance and help protect against rust. Easy-to-apply formula matches common appliance finishes for quick cosmetic repairs. What it does:

• Covers small chips, nicks and surface scratches to improve appearance
• Helps protect exposed metal from moisture and surface corrosion after damage
• Provides a precise application for targeted repairs on doors, panels and trim
• Can be used on painted steel and metal appliance surfaces (test in an inconspicuous area first)

• Clean and dry the repair area; remove loose paint and corrosion before applying
• Shake bottle well and apply sparingly with included applicator or a small brush
• Allow adequate drying time between coats and follow any manufacturer cure instructions on the label
• Wear gloves and work in a well-ventilated area; keep away from open flame and out of reach of children

This tub clamp secures a flexible seal or hose to the appliance's tub, maintaining a tight, leak-resistant connection. Replace a weakened or damaged clamp to stop leaks and keep the tub joint stable during operation.

• Applies even clamping pressure around the tub connection
• Helps prevent water leaks at the tub-to-seal or tub-to-hose joint
• Restores proper fit when the original clamp is stretched, stripped, corroded, or missing
• Common symptoms: water at the base/front, loose seal or hose, visible clamp damage

• Disconnect power and turn off water before service
• Access the tub connection; remove the old clamp and inspect the seal/hose for wear
• Clean mating surfaces; seat the seal evenly, position the clamp, and tighten until snug without pinching the rubber
• Run a quick fill/drain test and check for leaks

A U-bend retainer designed to secure a U-shaped heating element or tubing in place, preventing movement and vibration for reliable operation. Fits as the replacement hold-down clip used on compatible Whirlpool HVAC and appliance assemblies. What it does:

• Secures U-shaped element or tubing to the appliance frame or mounting bracket
• Prevents rubbing or vibration that can lead to wear or noisy operation
• Helps maintain proper spacing and alignment of the element for consistent performance
• Used where a compact, U-shaped clamp is required to hold components safely

• One U-bend retainer clip as shown

• Inspect the surrounding area and replaced part for damage before installing
• Use basic hand tools; align clip over the U-bend and fasten to the designated mounting point
• Disconnect power and allow components to cool before attempting repair
• Replace with the exact OEM fasteners

This transport cover secures internal components during shipping and service to prevent movement and damage. It helps keep parts aligned and reduces noise caused by loose components while the appliance is being moved. What it does:

• Holds internal components in place during transport to prevent shifting or impact damage
• Reduces rattles and vibration caused by unsecured parts
• Protects delicate assemblies from knocks during delivery or handling
• Helps maintain alignment of components until the appliance is installed

• One transport cover

• Disconnect power and water before servicing the appliance
• Remove all shipping brackets and covers per the owner's manual before normal operation
• Use manufacturer-specified fasteners and torque; do not force or modify the part

This small replacement clip secures panels, trim, or wiring so appliance components stay properly positioned and the unit operates quietly. A simple, low-cost part that prevents loose pieces from shifting or rattling during use. What it does

• Holds trim, panels or harnesses in place to prevent movement and noise
• Keeps wiring or small components secured to reduce wear from vibration
• Helps maintain proper alignment of plastic or metal assemblies
• Commonly used where a simple snap-in retainer is required

• One clip/retainer

• Disconnect power (and water if applicable) before servicing the appliance
• Inspect surrounding parts for damage; replace any cracked or broken mounting features
• Typically installs with pliers or by hand; avoid forcing to prevent breakage

This touch-up paint restores small chips and scratches on painted appliance surfaces to improve appearance and slow corrosion. It's a simple cosmetic repair that helps appliances look cared-for between major services. What it does:

• Covers minor paint chips, nicks and surface scratches
• Helps restore a uniform finish on exterior panels and trim
• Reduces likelihood of surface rust where bare metal is exposed
• Ideal for spot repairs on visible areas without repainting large panels

• One touch-up paint item for appliance finish

• Work in a well-ventilated area and protect surrounding surfaces
• Shake well and test on an inconspicuous spot before applying
• Apply sparingly in thin coats; allow each coat to dry per product instructions
• Keep out of reach of children and away from open flame

This small replacement clip secures a press (push) switch to the appliance control panel so the switch stays aligned and operates reliably. It restores proper button engagement and prevents the switch from working loose. What it does:

• Holds the press/push switch firmly in the control panel or console
• Keeps the switch aligned so button presses register correctly
• Helps stop intermittent or loose-feeling buttons caused by a failing retainer
• Prevents the switch from shifting or falling out during use

• Disconnect power before starting any repair to avoid shock or injury
• Access typically requires removing the control panel or console—retain screws and note their locations
• Clip installs by snapping into the panel and seating the switch; small pliers may help with alignment