Wfw915yw00 Parts

This touch-up paint restores small chips and scratches on painted appliance surfaces to improve appearance and slow corrosion. It's a simple cosmetic repair that helps appliances look cared-for between major services. What it does:

• Covers minor paint chips, nicks and surface scratches
• Helps restore a uniform finish on exterior panels and trim
• Reduces likelihood of surface rust where bare metal is exposed
• Ideal for spot repairs on visible areas without repainting large panels

• One touch-up paint item for appliance finish

• Work in a well-ventilated area and protect surrounding surfaces
• Shake well and test on an inconspicuous spot before applying
• Apply sparingly in thin coats; allow each coat to dry per product instructions
• Keep out of reach of children and away from open flame

This is a single replacement screw used to secure appliance panels and components. It restores proper fastening to help eliminate looseness and rattling and keep parts aligned for safe operation. What it does:

• Secures trim, panels or internal components to maintain proper alignment
• Prevents rattling or vibration caused by loose fasteners
• Replaces missing or stripped screws for safe, reliable fit
• Works wherever the OEM screw specification and fit match the original

• One screw as shown

• Disconnect power and/or gas before accessing internal components
• Use the proper driver size and avoid over-tightening to prevent thread damage
• Verify correct screw placement against the appliance's service diagram

This rear tub is the OEM replacement outer tub section that supports the wash basket and helps contain water inside the washer cabinet. Replacing a damaged rear tub restores proper drum alignment and helps prevent leaks. What it does:

• Supports the back of the wash basket and provides a mounting surface for the tub seal and bearings
• Helps contain water in the wash chamber to prevent cabinet leaks
• Restores proper drum alignment to reduce rubbing, vibration, and noise
• Addresses symptoms such as visible cracks or holes in the tub, persistent water leaks, or a misaligned/noisy drum

• Disconnect power and water supply before beginning any repair
• Drain the washer and remove the top, front, or rear panels as required for access
• Support the drum and follow the OEM disassembly sequence to avoid damaging seals or bearings
• If seals, bearings, or suspension components show wear, replace them at the same time for best results

This replacement screw secures appliance panels and trim so components stay properly aligned and vibration is reduced. Use it to replace missing or damaged fasteners and restore a secure fit for safe operation. What it does:

• Fastens control panels, trim pieces, or access panels to the appliance frame
• Prevents panel movement, rattling, or gaps that can form from loose or missing screws
• Restores proper alignment after service or part replacement
• Helps maintain safe, stable operation by keeping panels secured

• Disconnect power (and gas if applicable) before servicing the appliance
• Use the correct driver bit and thread engagement; hand-start threads to avoid cross-threading
• Do not overtighten — snug until secure to avoid stripping or damaging panel threads
• Keep removed hardware organized to ensure correct locations during reassembly

This rubber seal fits around the water temperature sensor where it passes through the tub or housing. It restores a watertight barrier at the sensor port to help prevent leaks and ensure reliable temperature feedback.

• Creates a watertight seal around the temperature sensor
• Helps prevent drips or leaks from the sensor opening
• Supports stable, accurate temperature readings during cycles
• Typical failure signs: cracked, flattened, or brittle seal; moisture at the sensor area; pooling water beneath the unit; temperature-related faults

• Disconnect power and turn off water supply before servicing
• Access the sensor location and drain any remaining water
• Withdraw the sensor, remove the old seal, and clean the seating surface
• Lightly moisten the new seal with water, seat it fully, reinstall the sensor, and check for leaks during a test cycle

A replacement knob assembly that restores secure, easy control of the appliance control shaft. Replaces worn, cracked, or missing knobs so settings can be selected reliably and with a positive grip. What it does:

• Replaces a damaged or missing control knob to restore user control over settings and cycles.
• Provides a solid, shaped grip for precise selection and adjustment.
• Addresses symptoms such as a cracked or broken knob, a knob that spins on the shaft, or a knob that will not engage or change settings.
• Matches the OEM-style interface so the knob fits and operates like the original.

• Disconnect power (unplug or shut off circuit) before starting any repair.
• Verify the control shaft style (splined, smooth, D-shaft, etc.) before installing to ensure proper fit.
• Many knobs are push-on; others secure with a set screw—use appropriate tools and avoid overtightening.

Drain hose retainer keeps the appliance's drain hose securely fastened to the cabinet or pump, helping prevent the hose from slipping loose. Replacing a broken retainer reduces leaks and improper draining caused by a detached hose. What it does:

• Secures the drain hose to the cabinet, pump outlet, or drain connection to maintain correct hose positioning.
• Helps prevent water leaks and hose disconnection during drain cycles.
• Common symptoms of a failed retainer: visible hose movement, water at the rear or floor, or intermittent draining issues.
• Replaces worn or broken retainers that no longer hold the hose firmly.

• Always disconnect power and turn off water before servicing the appliance.
• Access may require moving the appliance or removing a rear/access panel to reach the hose retainer.
• Seat the drain hose fully in its proper position, snap or clip the retainer into place, and verify the hose is secure and not kinked.
• Inspect the drain hose for cracks or wear while replacing the retainer; replace the hose if damaged.

Kit contains two 10 feet inlet hoses.