Wfw9550wl Parts

This outer tub is the large stationary tub that holds water for the washer and supports the inner wash basket. It restores a watertight enclosure and structural support so your washer can fill, agitate, and drain properly. What it does:

• Forms the watertight basin that contains wash water and directs it to the drain
• Supports the inner tub/basket and helps keep the basket aligned during cycles
• Prevents water from leaking into the cabinet when intact
• A cracked, warped, or corroded outer tub can cause visible leaks, loud or uneven operation, and washer shutdowns

• One outer tub

• Disconnect power and water supply before beginning any repair
• Drain remaining water and remove the washer top/lid and control panel as needed to access the tub
• Support or remove the inner tub/basket per service manual instructions to avoid damage during removal
• Inspect and replace related seals, gaskets, and clamps as needed

This clamp secures a flexible appliance hose to a fitting to help prevent leaks and keep connections tight. It's a small but essential part that restores a proper seal on water or drain lines. What it does:

• Holds a hose firmly to a tailpiece, barb or connector to reduce leaks and hose slippage
• Helps stop intermittent dripping or pooling caused by loose hose connections
• Restores a proper seal after hose replacement or maintenance
• Works on common appliance water/drain lines where this clamp style is used

• One hose clamp

• Disconnect power and shut off water to the appliance before starting any work
• Allow the appliance and hoses to cool if recently used; use gloves and eye protection
• Use appropriate pliers or a screwdriver (depending on clamp style) to remove and install the clamp; avoid over-tightening
• Inspect the hose and fitting for damage; replace the hose if cracked or worn

This replacement screw secures appliance panels and trim so components stay properly aligned and vibration is reduced. Use it to replace missing or damaged fasteners and restore a secure fit for safe operation. What it does:

• Fastens control panels, trim pieces, or access panels to the appliance frame
• Prevents panel movement, rattling, or gaps that can form from loose or missing screws
• Restores proper alignment after service or part replacement
• Helps maintain safe, stable operation by keeping panels secured

• Disconnect power (and gas if applicable) before servicing the appliance
• Use the correct driver bit and thread engagement; hand-start threads to avoid cross-threading
• Do not overtighten — snug until secure to avoid stripping or damaging panel threads
• Keep removed hardware organized to ensure correct locations during reassembly

The Vent Hose is an OEM part for Whirlpool washing machines. This vent hose allows air to circulate in and out of the washer, preventing pressure build-up and ensuring proper water drainage. It helps maintain the efficiency and effectiveness of the washing machine by facilitating the necessary airflow during the wash and spin cycles.

Common causes of a bad vent hose include wear and tear from regular use, blockages from lint or debris, and damage from mishandling or improper installation.

Symptoms of a bad vent hose include:

• Water not draining properly from the washer
• Unusual noises during the wash or spin cycles
• Leaks or water pooling around the washer
• Visible cracks, splits, or blockages in the hose

This OEM part is also compatible with some Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This exhaust hose carries drain water from the pump to the external drain connection on your washer. Replacing a worn or damaged hose restores proper draining and helps prevent leaks and musty odors.

• Directs discharge water from the drain pump toward the outlet
• Maintains a sealed flow path to help prevent leaks
• Age, vibration, or debris can cause cracks, splits, or clogs
• Common symptoms: water leaking under the unit, slow or no drain, visible cracks/kinks on the hose

• Disconnect power and turn off water supply before servicing
• Place towels or a pan to catch residual water; remove access panels as needed
• Compress/release spring clamps, transfer them to the new hose, and fully seat hose ends
• Run a short drain cycle to check for leaks

This dispenser drawer slides into the washer's dispenser housing and holds detergent and laundry additives for each cycle. Replace a cracked, stuck, or missing drawer to restore smooth operation and proper dispensing. What it does:

• Holds and organizes detergent and other laundry additives in labeled compartments
• Works with the dispenser housing to flush products into the tub at the correct time
• Helps contain liquids to reduce drips and spills around the dispenser area
• Typical failure symptoms: cracked/broken face or tabs, drawer binding or popping out, detergent left in the drawer, or water leaking at the dispenser

• 1 dispenser drawer

• Disconnect power and turn off water before servicing
• Fully extend the old drawer, press the release tab, and pull it free from the housing
• Move over any removable siphons or inserts from the old drawer if present
• Slide the new drawer in until it latches and glides smoothly; run a quick test cycle to check dispensing and leaks

This rubber seal fits around the water temperature sensor where it passes through the tub or housing. It restores a watertight barrier at the sensor port to help prevent leaks and ensure reliable temperature feedback.

• Creates a watertight seal around the temperature sensor
• Helps prevent drips or leaks from the sensor opening
• Supports stable, accurate temperature readings during cycles
• Typical failure signs: cracked, flattened, or brittle seal; moisture at the sensor area; pooling water beneath the unit; temperature-related faults

• Disconnect power and turn off water supply before servicing
• Access the sensor location and drain any remaining water
• Withdraw the sensor, remove the old seal, and clean the seating surface
• Lightly moisten the new seal with water, seat it fully, reinstall the sensor, and check for leaks during a test cycle

Drain hose retainer keeps the appliance's drain hose securely fastened to the cabinet or pump, helping prevent the hose from slipping loose. Replacing a broken retainer reduces leaks and improper draining caused by a detached hose. What it does:

• Secures the drain hose to the cabinet, pump outlet, or drain connection to maintain correct hose positioning.
• Helps prevent water leaks and hose disconnection during drain cycles.
• Common symptoms of a failed retainer: visible hose movement, water at the rear or floor, or intermittent draining issues.
• Replaces worn or broken retainers that no longer hold the hose firmly.

• Always disconnect power and turn off water before servicing the appliance.
• Access may require moving the appliance or removing a rear/access panel to reach the hose retainer.
• Seat the drain hose fully in its proper position, snap or clip the retainer into place, and verify the hose is secure and not kinked.
• Inspect the drain hose for cracks or wear while replacing the retainer; replace the hose if damaged.

This water inlet hose directs incoming water into the appliance for normal operation, providing a reliable pathway that maintains safe, consistent water flow. Use this OEM-fit hose to replace a cracked, leaking, or damaged inlet line. What it does

• Carries incoming water from the home's supply to the appliance's water valve or fill assembly.
• Restores proper filling when an old hose leaks, is split, or becomes deteriorated.
• Helps prevent water damage and maintains normal cycle performance when functioning correctly.
• Compatible with repairs where the original inlet hose is worn, kinked, or blocked.

• One new replacement water inlet hose.

• Disconnect power and shut off the water supply before starting any repair.
• Inspect hose fittings and seals; replace any worn clamps or gaskets for a secure, watertight connection.
• Route the hose without sharp bends or kinks and secure per the appliance's routing clips.

This power cord is the replacement electrical lead that supplies mains power to the appliance, restoring safe, reliable operation when the original cord is damaged or worn. What it does

• Delivers AC power from the wall outlet to the appliance's internal wiring and controls.
• Replaces frayed, cut, melted, or otherwise damaged cords that can cause intermittent power or safety hazards.
• Helps eliminate issues like no power, intermittent power loss, or visible cord insulation damage.
• Restores a secure connection at the appliance strain-relief and terminal block when installed correctly.

• One replacement power cord.

• Always disconnect power at the circuit breaker or unplug the appliance before installing.
• Inspect terminal block and strain-relief; replace any damaged hardware and secure the cord per the appliance wiring diagram.
• Follow the appliance manufacturer's wiring diagram for correct conductor routing and grounding.

This drum baffle (drum lifter) helps lift and separate laundry as the drum turns to promote even tumbling and improved air circulation for better drying. Designed to replace a worn or damaged lifter and restore normal drum action. What it does:

• Lifts and moves clothes during a drying cycle to prevent clumping and improve airflow
• Helps maintain even tumbling to reduce drying times and uneven drying
• Replaces broken, cracked or missing lifters that can cause noise or fabric snags
• Contributes to quieter operation by restoring proper load balance

• One drum baffle (drum lifter)

• Disconnect power (and gas supply if applicable) before starting any repair
• Replacement typically requires access to the dryer cabinet and drum — keep fasteners and clips in a safe place
• Inspect mounting points and surrounding drum for wear; replace any damaged hardware
• Test run the dryer after installation to ensure secure fit and normal operation

This replacement screw is a direct-fit fastening part used to secure panels and small components on compatible Whirlpool appliances. It restores proper fit and helps stop loose or rattling parts for reliable appliance operation. What it does:

• Secures trim, panels, or brackets to keep parts aligned and stable
• Prevents vibration-related noise caused by loose hardware
• Replaces missing or damaged screws that allow components to shift
• Restores factory fit where stripped or worn fasteners fail

• Disconnect power to the appliance before servicing to avoid electrical shock
• Use the proper screwdriver or driver bit to avoid stripping the head
• Install carefully and tighten until snug; do not overtighten
• Keep track of small parts and fasteners during disassembly

A small metal hose clamp that secures flexible hoses and tubing to fittings to help prevent leaks and keep connections tight. Simple, durable replacement for worn or loose clamps on appliance water and drain lines. What it does:

• Holds a hose or tube firmly on a barb or fitting to prevent leaks or disconnection
• Resists loosening from vibration and normal use
• Restores a secure connection when an old clamp is corroded, stretched, or broken
• Helps prevent water damage from loose plumbing connections

• One metal hose clamp

• Disconnect power and shut off water supply before servicing
• Slide clamp over hose, position over fitting barb, then compress or tighten as required
• Replace any damaged hoses or fittings when installing a new clamp
• Verify a leak-free connection before returning appliance to service

This steamer heater assembly produces the heat needed for a dryer's steam/refresh cycles so clothes receive steam for wrinkle reduction and odor release. Replaces a failed or weak steam heater to restore steam functionality. What it does

• Heats water into steam for the dryer's steam/refresh feature.
• Helps restore steam output when the steam option produces little or no steam.
• Can resolve issues where steam cycles do not start or clothing remains unrefreshed after a steam cycle.
• Works as the thermal element portion of the dryer's steamer system.

• One steamer heater assembly

• Disconnect power to the appliance before beginning any service.
• Handle the heater assembly carefully; avoid bending terminals or stressing mounts.
• Basic mechanical skill and common tools are typically required; for panel removal and wiring diagrams.