Wgd6120hw Parts

This 8 ft flexible exhaust hose directs airflow from the appliance to the home vent, helping maintain proper ventilation and reduce moisture and lint buildup. It's a straightforward replacement for worn or damaged ducting. What it does:

• Channels exhaust air from the appliance to the exterior vent
• Restores proper airflow to help reduce drying times and moisture buildup
• Helps prevent lint accumulation in the appliance exhaust pathway
• Reduces risk of poor performance caused by crushed, torn, or disconnected ducting

• One 8 ft flexible exhaust vent hose

• Disconnect power to the appliance before replacing the vent and follow all safety precautions
• Remove old ducting carefully to avoid scattering lint; clean vent openings before installing the new hose
• Ensure secure clamps or connections at both appliance and wall/roof vent to prevent leaks
• Follow local building codes and venting recommendations for appliance type and location

This periscope extension piece helps position or extend a small duct/vent component inside the appliance so airflow or sensing elements reach the correct location. It's a simple replacement that restores proper alignment and fit. What it does

• Provides a 0.5-inch extension/positioning for an internal vent or sensor tube
• Restores proper clearance and alignment of airflow or sensing components
• Can reduce airflow restriction or misalignment-related symptoms
• Helps resolve intermittent venting, sensor mispositioning, or fitment issues

• One periscope extension piece

• Typical replacement is a simple swap; power off and unplug the appliance before starting
• Remove any access panels needed to reach the original periscope; retain mounting clips or gaskets
• Inspect surrounding parts for damage and replace if worn to ensure proper seal and operation

This retainer clip secures small appliance components in place to prevent movement and ensure proper alignment for reliable operation. It's a simple replacement that restores lost or broken mounting support. What it does:

• Holds and stabilizes the attached component or assembly to prevent shifting during use
• Maintains proper alignment for connected parts to reduce wear and noise
• Commonly used where a small plastic or metal clip is needed for secure mounting
• Can address symptoms like loose panels, rattling, or parts that won't stay seated

• One retainer clip

• Disconnect power to the appliance before attempting any repair
• Remove surrounding panels as needed to access the clip; small trim tools may help
• Replace the broken retainer with the new clip and verify the secured component is seated correctly

This wire harness routes power and signals between the appliance control and components to restore electrical connections and proper operation. It replaces a worn, damaged, or corroded wiring assembly to help eliminate intermittent power or control issues. What it does

• Carries power and control signals between the main control and components
• Replaces damaged, frayed, or corroded wiring that can cause intermittent operation
• Helps restore reliable electrical connections to resolve no-power or faulty-control symptoms
• Matches OEM connector types and pin layout for straightforward replacement when correct part number is used

• One complete wire harness as shown

• Disconnect power before starting any repair to avoid shock or equipment damage
• Handle connectors by the housings; avoid pulling on wires to prevent damage

This is a replacement sheet-metal screw used to secure panels and components on compatible Whirlpool appliances. It provides a reliable fasten point for reattaching trim, brackets, and access panels after service. What it does:

• Secures appliance panels, brackets, and smaller components to the cabinet or frame
• Helps restore original fit and finish after repairs or part replacement
• Prevents rattles or loose panels when properly installed
• Matches OEM thread size and head style for a correct fit

• Turn off and unplug the appliance before removing panels or installing hardware
• Use the correct driver bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing to prevent thread damage or warped panels

This wire harness assembly routes power and signals between components to restore electrical connectivity and reliable operation. It replaces a damaged or worn harness so controls and motors can receive proper power and communication. What it does:

• Provides factory-style wiring connections between control, motor, and switches
• Restores power or signal continuity when original harness is damaged or corroded
• Stops intermittent operation caused by loose or broken wires and connectors
• Prevents arcing or shorting from exposed or frayed conductors

• Disconnect all power before starting work to avoid shock or injury
• Inspect connector ends and routing; match original wire paths and secure with clips/ties
• Do not splice or patch severely damaged wires—replace the entire harness

The Door Switch is an OEM component specifically designed for Whirlpool brand dryers. This door switch works to detect when the dryer door is open or closed and cuts power to internal components when the door is open for safety. 

Causes of a bad door switch can include wear and tear over time, exposure to excessive shock or impact, or moisture damage. 

Symptoms of a bad door switch include: 

• The dryer operates with the door open 
• Inability to start or run the dryer
• Error codes or fault messages relating to door detection

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models. 

This drum baffle restores proper tumbling by lifting and separating laundry as the dryer drum rotates. It helps improve drying performance and reduces garment bunching. What it does:

• Lifts and tumbles clothes so air flows more evenly through the load
• Helps prevent garments from clumping or wrapping around the drum
• Can reduce rubbing, thumping, or scraping noises caused by a loose or damaged lifter
• Restores consistent drum contact and improves drying efficiency

• Disconnect power before starting any repair to avoid shock or injury
• Access typically requires opening the dryer cabinet or front panel; small tools may be needed
• Align the baffle with factory mounting holes and secure with existing fasteners; use correct screws if replacements are required
• Inspect and replace worn drum or support parts as needed for reliable operation

Small replacement clip that secures panels or small internal components to restore a snug fit and reduce rattling or misalignment. Use this clip when a worn or broken retainer lets trim or parts sit loose. What it does:

• Holds trim, panels or other small appliance components in place to maintain correct alignment.
• Helps eliminate rattling, vibration noise or gaps caused by a missing or damaged clip.
• Restores secure fit where a broken clip allows parts to shift or separate.
• Simple, low-profile replacement part used in affected Whirlpool appliances.

• Disconnect power (unplug or shut off breaker) before servicing any appliance.
• Small part; keep track of screws and retainers during disassembly.
• Basic hand tools may be required; trim or panel removal might be necessary to access the clip.

Dryer Vent Test Kit ensures your dryer's vent system is operating properly. Kit includes two tests depending on the location of your dryer's lint screen: One for the lint screen in the top of your dryer, and one for the lint screen in the front of your dryer. Instructions included.

This is a drum assembly used in many home dryers. The component is located inside the appliance and is tasked with holding the clothing during a dryer cycle. It is made of durable materials but can experience wear and tear or damage that cause it to malfunction. If the drum assembly is worn or damaged, it may cause the appliance to buzz or squeal, start and stop, and seize up during use.If the drum assembly is damaged or worn, it will need to be replaced. This will require a set of tools and a pair of work gloves. Before starting the replacement process, make sure the dryer is unplugged from the wall. The dryer will need to be disassembled to access the drum assembly. The belt can be used to pull out the drum so the new component can be installed. Replace the part and reassemble the dryer. It should be plugged back in before use.This part is sold on an individual basis. It is designed to be used with several dryers created by Admiral, Amana, Maytag, Kenmore, and Whirlpool. The drum assembly is an authentic OEM replacement part that is sourced directly from the manufacturer.