Whirlpool Du810swpq4 Parts

This is the tub funnel seal used to create a watertight connection at the washer tub funnel, helping prevent leaks and keep water flowing to the wash tub where it belongs. It replaces a worn, cracked or flattened seal. What it does:

• Creates a water-tight seal between the tub funnel and surrounding housing to prevent leaks
• Helps keep water directed into the wash tub during fill and drain cycles
• Worn or damaged seals can cause visible water around the top or cabinet and reduced containment
• Replacing a degraded seal restores proper sealing and reduces drip/leak symptoms

• Disconnect power and turn off water supply before starting any repair
• Remove the washer top/agitator or other access panels as required to reach the funnel area
• Inspect mating surfaces and clean away residue before seating the new seal for a proper fit
• Test with a short fill cycle to check for leaks after installation

This disk mount is a small replacement mounting disk that secures and aligns internal components so the appliance operates quietly and reliably. It restores proper fit where a worn or damaged mount causes misalignment or vibration. What it does:

• Provides a secure mounting point for internal assemblies and helps maintain correct component alignment
• Reduces vibration and rattling caused by a broken or deteriorated mount
• Supports stable operation and prevents excess wear on adjoining parts
• Commonly replaced when mount is cracked, warped, or missing

• One disk mount as shown

• Basic hand tools typically required; inspect surrounding components for damage before reassembly
• Disconnect power and/or gas and follow appliance safety procedures before starting work
• Retain all fasteners and observe correct orientation during installation

This collector hose assembly routes and channels water inside the appliance to the drain area, helping maintain proper water flow during cycles. It replaces worn, cracked, or leaking collector hoses to reduce leaks and maintain performance. What it does:

• Channels wastewater from internal tub components to the drain system
• Helps prevent leaks caused by cracked, split, or brittle hose sections
• Restores proper routing when the original hose is kinked, collapsed, or damaged
• Compatible with factory routing and mounting points for correct fit

• Disconnect power and water supply before starting any repair
• Inspect adjoining clamps and fittings; replace if corroded or damaged
• Follow OEM routing and secure with the original clamps or new OEM-style clamps

This wheel leg is a replacement support used to stabilize and allow smooth movement of the appliance's lower assembly. It restores proper leveling and reduces wobble so the appliance sits securely and rolls or rests as designed. What it does

• Supports the appliance chassis at the lower corner and transfers load to the floor
• Helps maintain correct appliance height and leveling to reduce vibration and rocking
• Restores proper rolling or stationary support where a worn or broken leg caused instability
• Commonly replaced when the leg is cracked, stripped, missing, or no longer holds weight

• Verify appliance is unplugged and empty before accessing lower cabinet or base
• Support the appliance with a block or jack to prevent shifting while replacing the leg
• Remove any access panels or retaining hardware as needed; install the new leg in the original orientation
• Replace any fasteners that are damaged and test stability before returning the appliance to service

This support bearing assembly stabilizes the dryer drum and helps it spin smoothly to improve tumbling and reduce noise. Designed to replace a worn or noisy rear drum support for compatible Whirlpool dryers. What it does:

• Supports the rear of the dryer drum so it rotates evenly
• Reduces squeaks, grinding, and wobbling caused by worn bearings
• Helps maintain proper drum alignment to prevent uneven wear
• Works with the drum shaft to keep tumbling smooth during operation

• One support bearing assembly

• Disconnect power before beginning any repair to avoid electrical shock
• Access may require removing the dryer rear panel and drum; follow manufacturer service instructions
• Inspect adjacent components and replace if excessively worn
• Tighten fasteners to manufacturer torque specs and test operation after reassembly

Size: 8-32 x .312 inch.

Color: White. Includes insulation. Other colors: For almond use WP3384157, for biscuit use WP3384157, for black use WP3379920.

This flexible replacement hose routes water safely in your appliance to restore normal water flow and prevent leaks. It replaces a worn, cracked, or leaking factory hose so your appliance can operate reliably. What it does:

• Carries water between components to maintain proper appliance operation
• Helps stop leaks caused by brittle, cracked, or damaged hoses
• Compatible with original mounting and connection points when replacing the same part number
• Common symptom: visible leaks, reduced water flow, or water pooling near the appliance

• Turn off power and shut off water supply before attempting replacement
• Inspect fittings and clamps; reuse only if undamaged, otherwise replace with proper hardware
• Ensure secure, leak-free connections and verify no kinks in the hose after installation