Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Washer won't start or stops mid-cycle? A damaged lid switch shield can expose wiring to moisture, causing safety interlock failures. Simple fix.
Suspension skate plate mounts under the washer drum to support the tub assembly. Replace if cracked, broken, or warped. Includes suspension pads.
Washer lid hinge attaches the lid to the cabinet, allowing smooth opening and closing. Replace if cracked, rusted, broken, or causing lid misalignment.
With the parts supplied from your company. The lady that took my order was good at her job. All the parts were correct and fit. I thank you for the service that recieved. Read more
Fix dryer electrical connection issues with this terminal. Common when dryer won't start or power cuts out. Simple plug-in repair for most models.
Washer won't spin or makes noise during spin? This clutch spring cap maintains proper tension in the drive assembly. Quick 5-minute DIY repair.
I bought a clutch liner kit installed it in 5 minutes now it spins faster than ever. Read more
Knurled pin secures knobs or dials to control shafts in washers. Replace if the original is missing, worn, or damaged to stop loose or spinning knobs.
Weekend laundry became very noisy, our 1987 Whirlpool washer began doing a dance across the floor and the drum was banging into the inner cabinet. After doing some research and watching a few videos on Appliance parts pros website. I inspected the washer and noticed one leg the rubber coating disintegrated, decided to change all four legs, springs and lid switch. Hardest part of the job is getting the cabinet together. Ops check good. Read more
Washer won't fill, overfills, or leaks? A faulty water inlet valve is often the cause. DIYers report 10-20 minute fixes for this common washer repair.
Replaced washer water inlet valve. Read more
Fix dryer electrical connection issues with this terminal. Used for wiring connections in heating and control circuits. Simple installation in minutes.
Gray acrylic spray paint for coating worn or chipped dryer drum interiors. Restores the protective finish when the original coating is scratched or flaking.
Completely removed dryer drum cleaned surfaces ready for paint applied paint acquired from you it did a wonderful job with one can of paint will use for a while and acquire another can of paint for second coat thank you so much for your help the whirlpool dryer drum paint was exactly what it said it would do Read more
Ground screw secures transmission housing and console components in washers. Replaces missing, stripped, or corroded screws. 10-24 x 3/8 inch fastener.
Replaced timer control unit, first time doing this. Read more
Fix dryer drum rattling noise with this lock nut. Secures drum rollers, pulleys, and shafts to prevent loosening from vibration. Simple DIY fix.
The cylinder roller that supports the dryer drum was worn and needed to be replaced. I ordered the idler pulley shaft and associated parts as well since I wasn't sure if these were worn too. Watching the video on the web site gave me a good idea what was involved and where to look. It wasn't my exact model and make but provided sufficient information on what to look for. The parts were exact fits which was a great relief abd the dryer is running like new again! Read more
Lever mechanism popping loose or control not engaging? This retaining clip locks the linkage in place. Cabinet removal required for access. DIY-friendly repair.
Ordered the broken and missing part Read more
Screw-washer assembly secures panels and brackets in your washer dryer combo. Replace if worn, missing, or stripped to restore secure fastening.
0.6 oz. platinum touch-up paint with brush for appliances. Repairs scratches, chips, and gouges on doors, handles, and trim panels. Acrylic formula.
Replacement shaft sleeve bushing for washers. Fits over rotating shafts to reduce friction and protect surfaces. Replace when worn, cracked, or missing.
Connects drain hose sections to prevent leaks and restore proper wastewater drainage. Replace if coupling cracks or connection leaks during draining.