Whirlpool Wdf310paas1 Parts

This left-hand door hinge supports and pivots the door so it opens smoothly and closes tight. Replace a worn hinge to correct sagging, rubbing, or doors that won't seal—improving performance and preventing damage. What it does:

• Provides the pivot point for the door on the left side
• Maintains alignment so the door sits level and latches/seals properly
• Helps the door open and close smoothly without binding
• Common symptoms: door sags or rubs, won't close fully, uneven gaps, squeaking/grinding noises, poor seal

• One left-hand door hinge

• Disconnect power; also shut off gas and/or water before servicing
• Support or remove the door before unfastening the hinge; some hinges may be under spring tension—use caution
• Transfer original hardware/shims as needed and tighten fasteners securely
• Check door alignment and gasket contact after installation; open/close several times to ensure smooth operation

• "Left-hand" is determined when facing the front of the appliance.

Right-hand door hinge that replaces a worn or damaged refrigerator door hinge to restore proper door alignment and smooth opening and closing. Helps maintain a tight seal and prevents door sag or binding. What it does:

• Supports and pivots the refrigerator door on the right-hand side for correct alignment.
• Restores smooth opening/closing and reduces rubbing or scraping at the cabinet.
• Helps re-establish a full door seal to prevent cold air loss and temperature issues.
• Addresses symptoms such as a sagging or misaligned door, noisy hinge movement, or a door that doesn't close evenly.

• Disconnect power to the appliance and remove any items from the door before starting.
• Support the door while removing hinge hardware to prevent sudden drops or damage.
• Reuse existing screws/hardware unless replacement hardware is provided; tighten securely but avoid over-torquing.
• After installation, check door alignment and gasket contact; adjust hinge position as needed to ensure proper sealing.

The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber. 

Symptoms of a faulty Thermostat Clip can include:

• Fluctuating or inconsistent water temperatures between cycles 
• Inability to properly detect temperature for desired heat levels
• Longer cycle times needed for reaching required temperatures
• Strange sounds or condensation around thermostat connection

Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.

This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well. 

This support bracket helps hold internal components in place to restore proper alignment and reduce movement. It's a simple replacement that stabilizes the affected assembly and helps stop rattling or sagging. What it does:

• Secures and supports a loose or misaligned internal component or panel
• Prevents shifting that can cause vibration, noise, or uneven operation
• Restores proper alignment to reduce wear on adjoining parts
• Functions as the OEM replacement for the original support bracket

• One support bracket

• Inspect the mounting points and surrounding parts for wear before installing
• Replace only with the matching OEM part number to ensure fit; fasten securely per manufacturer torque recommendations
• Disconnect power and follow basic safety precautions before servicing the appliance

This Tube-Feed supplies water to the appliance's ice/water system, restoring proper water flow to the ice maker or dispenser. A direct-fit replacement that helps stop reduced ice production or interrupted water delivery. What it does:

• Routes incoming water from the inlet to the ice maker or dispenser assembly
• Restores proper water flow when the original tube is cracked, kinked, or clogged
• Helps stop leaks or puddling caused by damaged tubing when installed correctly
• Works with the appliance's original fittings and seals to maintain a secure connection

• One Tube-Feed

• Disconnect power and shut off the water supply before starting any repair
• Inspect fittings and seals; replace any damaged clamps or gaskets for a watertight connection
• Avoid sharp bends or kinks when routing the tube; secure with existing clips
• Turn water back on and check all connections carefully for leaks before restoring power

The Control Light Reflector is an OEM part for Whirlpool dishwashers. It is located inside the control panel area and is responsible for reflecting light from the interior control lighting. This helps illuminate the control buttons and display screen for ease of use and readability.

Causes of a bad control light reflector can include cracks, chips or discoloration to the reflective surface, reducing its effectiveness over time. 

Symptoms of a bad control light reflector include:

• Dim or poorly lit control buttons and display screen  
• Difficulty seeing settings and cycle status
• Increased difficulty operating the controls in low-light rooms

This Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This brace connector is a small structural support that secures and stabilizes appliance components, helping maintain proper alignment and reduce vibration. It restores firm attachment where a worn or broken connector causes movement. What it does:

• Secures joining points between panels or assemblies to prevent looseness and rattling
• Restores proper alignment of connected parts so doors, panels, or controls operate smoothly
• Helps reduce vibration and noise caused by a failed or missing connector
• Works as the replacement structural fastener specified by the manufacturer

• Disconnect power (and water if applicable) before beginning any repair
• Basic hand tools (screwdriver, socket) typically required; inspect mounting hardware and replace if damaged
• Verify correct orientation and tightness during installation to avoid stressing adjacent parts

This connector links mating components within the appliance to create a secure, reliable connection. Replacing a cracked or loose connector helps restore consistent operation and prevent intermittent issues caused by poor contact or separation. What it does:

• Creates a stable connection between mating parts or harnesses in the appliance
• Helps prevent looseness or separation that can disrupt performance
• Direct replacement for broken, brittle, or deformed connectors
• Can resolve intermittent operation traced to a poor connection at this junction

• 1 connector

• Disconnect power and, if applicable, shut off water before servicing
• Note orientation and positions before removal to ensure correct reassembly
• Seat the connector fully until any locking features engage; do not force
• Inspect mating parts for wear or damage and replace if necessary

Color: White

This control panel is the user-facing interface that houses the appliance's buttons and display so you can select cycles and monitor status. It restores a worn or damaged console for normal operation and clear feedback. What it does:

• Provides the front-mounted buttons and display used to select cycles and options
• Transmits user selections to the appliance's main control for proper operation
• Replaces faded, cracked, or unresponsive panels that make controls hard to read or press
• Helps restore a secure mounting surface for switches and indicators

• One replacement control panel

• Disconnect power (and water, if applicable) before beginning any repair to avoid shock or injury
• This panel typically mounts to the console with screws or clips; remove trim to access mounting hardware
• Handle with care to avoid damaging button surfaces or display lens during installation

Color: White. Size: 1 qt. can. Acrylic appliance paint.