Whirlpool Wrf993fifm00 Parts

The Wire Harness is an OEM part for Whirlpool refrigerators. It forms the bundled network transmitting power and signals between electronic control boards and internal components.

Symptoms of a bad wire harness can include intermittent or complete component failures due to wire insulation cracks exposing live connections to moisture. Physical stress from frequent door openings may also nick individual electrical lines.

Causes of a bad wire harness typically involve long-term vibration wear and repeated flexing/abuse of wires near hinge points. Sharp shelving edges pose an abrasion risk over many years of use.

Symptoms of a bad wire harness include:

• Lights or temperature displays that suddenly cut out  
• Ice/water dispenser that fails to operate
• Frequent error codes related to specific zones or shelves
• Buzzing or arching sounds near routing points

Compatible brands include KitchenAid, Jenn-Air, and Kenmore models.

This stop door is a replacement door stop that helps the appliance door close securely and stay in position. Restores proper door movement and reduces rubbing or misalignment that can cause noise or poor sealing. What it does:

• Replaces a worn or broken door stop to restore normal door closing and positioning
• Helps prevent the door from bouncing, rubbing, or hanging open
• Can reduce door-related noise and improper sealing during use
• Supports reliable door alignment for safer operation

• Disconnect power to the appliance before starting any repair
• Remove the door or access panel as needed to reach the mounting area
• Typical installation uses basic hand tools (screwdriver, nut driver); retain existing fasteners unless replacement hardware is provided
• Inspect surrounding hinges and catches and replace if damaged

This ice door is the replacement plastic flap that covers the freezer ice chute and opens to release ice from the dispenser. It helps keep cold air in the freezer and prevents debris from entering the ice chute when not dispensing. What it does:

• Opens and closes to allow ice to pass from the ice bin into the dispenser
• Helps maintain proper freezer temperature by sealing the ice chute when closed
• Prevents ice, moisture, and debris from entering the dispenser opening
• Commonly replaced when the door is cracked, warped, stuck, or won't stay closed

• One ice door (single replacement flap)

• Disconnect power to the refrigerator before beginning any repair to avoid personal injury
• Access usually requires removing the dispenser trim or inner door panel—keep hardware organized during disassembly
• Handle the replacement door carefully to avoid cracking; ensure proper alignment so it opens and closes freely
• If the door does not operate after installation, check surrounding linkage and actuator components

A right-hand stop pan that secures and positions the assembly to prevent over-travel and maintain proper alignment. Restores correct movement and helps reduce noise or binding caused by a damaged or missing stop pan. What it does:

• Holds the component in the correct position to limit travel and prevent contact with adjacent parts
• Helps maintain proper alignment for smooth operation
• Can reduce rubbing, binding, or abnormal noises when worn or broken
• Supports reliable function of the surrounding assembly

• Disconnect power (and water if applicable) before starting any repair
• Access may require removing exterior panels or trim; keep track of fasteners
• Inspect surrounding mounts and hardware; replace any damaged clips or screws

Size: 63-1/2 x 35-1/2 x 2-5/8 inch.

Size: 3/16 inch.

Size: 5/16 inch.

Size: 3/8 inch.

Size: 3/4 inch.

This replacement valve cover protects and secures the washer's inlet valve assembly, helping keep water and wiring contained and reducing risk of leaks or damage. It restores the valve area's original shielding and fit. What it does:

• Covers and protects the water inlet/valve area from splashes and debris
• Helps keep valve wiring and connections properly routed and contained
• Can stop water spray from a damaged or misaligned valve area
• Restores correct mounting/fit to prevent valve movement and noise

• One replacement valve cover

• Disconnect power and shut off water before starting any repair
• Basic hand tools are typically required; access may require removing the top or control panel
• Align cover tabs and secure fasteners until snug; do not overtighten
• Inspect nearby seals, hoses and valve connections while accessible

This genuine replacement clip secures small appliance components in place to prevent rattling and part separation. It restores proper alignment so panels, trim, or internal assemblies stay firmly fastened during normal use. What it does:

• Fastens and retains panels, trim, or small assemblies to the appliance frame
• Prevents parts from shifting, vibrating, or causing operational noise
• Helps maintain proper alignment of connected components
• Commonly replaced when clip is cracked, missing, or no longer holds

• One replacement clip

• Disconnect power (and gas if applicable) before servicing the appliance
• Use needle-nose pliers or a flat tool to remove and install the clip; avoid excessive force
• The clip seats fully in its mounting slots and secures the mating part

This heater is the dryer heating element assembly that provides the heat needed for normal drying cycles, restoring effective drying performance when the element has failed. Installs in the dryer's heater housing to warm incoming air. What it does:

• Heats air that passes through the dryer drum to dry clothes
• Common repair for dryers that produce no heat or take much longer to dry
• Can help resolve intermittent heating or weak heat symptoms when element breaks or shorts
• Works as the primary replaceable heating component in the dryer's heater housing

• Disconnect the appliance from power before starting any repair.
• Replacement requires access to the dryer's rear or front panel and basic hand tools; follow OEM service instructions.
• Inspect related components (thermostats, fuses, wiring, venting) for damage or failures while replacing the heater.

This wire harness connector restores a reliable electrical connection between appliance wiring and components, helping eliminate intermittent power or control issues. It's a direct-replacement style part used where a broken or loose connector prevents proper function. What it does:

• Provides a secure electrical mating point between wiring and a control, sensor, or component
• Re-establishes continuity when a cracked, corroded, or damaged connector causes intermittent operation
• Helps stop flickering lights, components that don't power on, or erratic control behavior when connection is the cause
• Matches the OEM connector shape and pin layout for a correct fit and electrical contact

• Disconnect power (unplug appliance or shut off breaker) before inspecting or replacing electrical connectors
• Verify connector orientation and pin engagement; do not force if alignment feels incorrect
• Inspect wiring and terminals for damage; replace or repair any frayed wires or corroded terminals before reinstalling

Size: 1/4 lb.

Size: 1/4 inch.