Wm-16220Fd Parts

This spring-style hose clamp secures a washer's rubber hose to its fitting to maintain a tight, leak-resistant seal. Replacing a weakened clamp helps stop drips and keeps the hose firmly in place during operation.

• Provides constant spring tension to hold a rubber hose on its port
• Helps prevent leaks at the connection point
• Resists vibration so the hose doesn't back off the fitting
• Common signs include water at a hose joint, a loose/detached hose, or a rusted/broken clamp

• Disconnect power and turn off water supply before servicing
• Place a towel or pan to catch residual water from hoses
• Use pliers to compress the ears, slide off the old clamp, position the new clamp behind the hose bead, and release evenly
• After reassembly, run a quick test cycle and check for leaks

This replacement refrigerator door gasket seals the door to keep cold air inside, helping restore proper cooling and reduce frost, condensation, and energy loss from a damaged or worn seal. What it does:

• Creates an airtight seal around the refrigerator door to maintain internal temperature.
• Prevents warm air infiltration that can cause frost buildup and uneven cooling.
• Reduces condensation and helps improve compressor efficiency when sealing properly.
• Common symptoms of a failing gasket: visible cracks or gaps, cold air leaks, frost or moisture buildup, and higher energy use.

• Remove the old gasket and clean the door flange before installing the new seal.
• Press the gasket evenly into the door channel; some models use retaining clips or screws—model-specific instructions.
• Check that the gasket seats uniformly with the door closed and make minor adjustments as needed.

This washer shock absorber mounts between the outer tub and base to control movement during spin. Replacing a worn damper restores stability, reduces vibration and noise, and helps prevent the machine from walking or banging.

• Stabilizes the tub during spin by absorbing and controlling movement
• Reduces vibration and cabinet noise for smoother operation
• Helps the washer reach and maintain proper spin speed
• Worn shocks can cause shaking, banging, or walking during spin

• Disconnect power and water; use gloves and protect the floor.
• Access from the front or rear depending on model; remove panels as needed.
• Support the tub, then remove fasteners at both ends; install the new damper in the same orientation and tighten securely.
• Reassemble, level the washer, and run a test spin to check for vibration.

AC pump motor assembly replaces a failed pump drive to restore proper water removal. Direct-fit replacement restores pump operation to stop standing water, noisy pumping, or continuous filling issues in compatible LG machines. What it does:

• Drives the washer/dishwasher pump to move water out of the tub or through the circulation system.
• Restores proper drainage when a worn motor causes the unit to fail to pump water.
• Stops humming, grinding, or high-pitched noises caused by a failing pump motor.
• Helps prevent leaks or overflow caused by a non-operating pump (when pump seals and hoses are intact).

• Always unplug the appliance and shut off water supply before starting repairs.
• Access the pump from the front/bottom service panel; support the tub or cabinet as needed to avoid strain.
• Keep original wiring orientation and mounting hardware; transfer gaskets/seals or replace if damaged.
• After installation, run a test drain cycle to ensure proper operation before full reassembly.

Locking pin for shock absorber.

This clamp assembly secures a hose or tubing connection to maintain a watertight seal and reduce vibration. Replacing a worn or damaged clamp helps stop leaks and prevents hoses from slipping loose during operation. What it does:

• Holds a hose or tube firmly in place to maintain proper sealing at the connection point.
• Prevents leaks caused by loose, cracked or corroded clamps.
• Reduces vibration and rattling from unsecured hoses.
• Common symptom: visible leaking, water pooling, or a loose hose connection.

• Disconnect power and shut off water supply before starting any repair.
• Use the correct pliers or screwdriver for the clamp type; avoid damaging the hose.
• Inspect the mating hose and seal; replace any cracked or hardened hoses before reinstalling.
• Do not overtighten—tighten just enough to secure the hose without cutting or deforming it.

This clamp secures hoses or wiring to the appliance chassis to prevent movement, chafing, and vibration-related wear. It helps keep connections stable so hoses and wires stay in place during normal use. What it does:

• Holds water, drain or vent hoses in position to reduce strain and prevent rubbing
• Keeps wiring harnesses routed and fastened to avoid chafing or accidental disconnection
• Reduces vibration-related noise caused by loose hoses or wires
• Helps prevent hose kinks and unintended movement that can lead to leaks or intermittent electrical issues

• One clamp

• Disconnect power to the appliance before servicing; shut off water supply if working with water lines
• Remove panels as needed to access the hose or wiring route, then replace the clamp in the same orientation
• Use appropriate pliers or a screwdriver if required; do not overtighten or deform the hose or wiring
• If the original clamp was secured with a fastener, retain and reuse it only if undamaged; replace any stripped or broken hardware

This is a replacement single electrical harness that restores the factory wiring connection between components. It provides a like-for-like connection to help return affected functions to normal operation when wiring is damaged. What it does:

• Carries electrical signals/power between components and the appliance control circuits
• Replaces frayed, melted, or broken wiring that can cause intermittent or complete function failure
• Commonly used when a component has no power, a circuit is open, or functions stop responding
• Helps eliminate loose connector issues that cause intermittent operation or error codes

• One (1) single electrical harness (part 6877ER3003C)

• Always disconnect power (unplug or shut off breaker) before inspecting or replacing wiring
• Match connector shapes and pin counts; do not force connectors—verify secure seating
• Route and secure the harness per factory paths and clips to prevent chafing or heat exposure
• If you see melted connectors, burned insulation, or repeated failures,

This knob assembly replaces a worn or broken control knob so you can reliably set and adjust appliance settings. It restores a secure, easy-to-turn interface for the appliance's control shaft. What it does:

• Fits onto the control shaft to allow manual selection of settings and temperatures.
• Replaces cracked, stripped, or loose knobs that no longer grip the control shaft.
• Helps resolve issues where the control won't turn smoothly or slips while changing settings.
• Restores tactile feedback for accurate user control.

• Disconnect power to the appliance before removing or installing the knob.
• Pull the old knob straight off the control shaft.
• Align the knob's internal splines with the control shaft and push until fully seated.
• If knob does not seat or control still slips, inspect shaft splines and replace damaged components as needed.

This DC pump motor assembly drives the appliance pump to move and remove water during drain and circulation cycles. It restores pump operation so the washer/dishwasher can empty properly and avoid standing water. What it does:

• Powers the drain/recirculation pump to move water out of the tub during drain and wash cycles.
• Common repair when the appliance fails to drain, leaves standing water, or shows drain-related errors.
• Helps restore normal water flow for wash, rinse and drain sequences.

• Disconnect power (and water, if applicable) before servicing the appliance.
• Inspect hoses, filters and the pump housing for clogs before replacing the motor.
• Note connector orientation and mounting location; transfer gaskets/seals if the original must be reused.

A replacement hose clamp that secures a flexible hose to its fitting to help prevent leaks and disconnections. Restores a tight, reliable seal so hoses stay seated during normal use. What it does:

• Holds a rubber or plastic hose firmly to a pump, valve or connection to prevent leaks.
• Helps stop hose pull-off that can cause water leaks or appliance interruptions.
• Commonly replaced when clamps are corroded, bent, cracked or missing.
• Works as a low-cost repair to restore a secure hose connection without replacing the hose assembly.

• Disconnect power to the appliance and shut off the water supply before servicing.
• Use the correct tool (slip-joint pliers for spring-style clamps or a screwdriver for screw-type clamps) and avoid pinching the hose.
• Inspect the hose and fitting for damage; replace the hose if it's cracked or excessively worn.
• After installing, restore power/water and run a short test cycle or check for leaks.

This accessory assembly is a genuine replacement component that restores the appliance's accessory fit and function. It installs in the accessory area to secure and connect related parts for reliable operation. What it does:

• Replaces a damaged or missing accessory assembly to restore proper attachment and alignment
• Secures accessory components so controls and moving parts operate smoothly
• Commonly used when accessories are loose, broken, or no longer seating correctly
• Helps prevent rattling, misalignment, or intermittent accessory-related issues

• Disconnect power (and water, if applicable) before starting any repair
• Basic hand tools are typically required; follow the appliance's service manual for exact steps
• Keep fasteners and small parts organized during removal and reassembly

This hinge spring restores proper tension to the door so it opens and closes smoothly and stays aligned. Replacing a fatigued spring helps prevent sagging or slamming and supports a consistent, reliable door close.

• Provides the return tension/counterbalance for the door hinge mechanism
• Assists smooth opening/closing and helps the door stay properly aligned when latched
• Helps maintain consistent closing force over time
• Failure symptoms include: door drops quickly, won't stay aligned or fully closed, weak/squeaking spring action

• Disconnect power before service; allow any hot surfaces to cool
• The hinge and spring are under tension—support the door and release/install tension carefully
• Note spring orientation and hole positions before removal; match them on installation
• Access may require removing trim or the door; keep fasteners organized for reassembly

This pump hose routes washer tub water to the drain pump, helping remove wash water during the drain cycle. Replace a cracked or clogged hose to stop leaks and restore normal draining. What it does:

• Channels tub water to the drain pump so the washer can expel water during drain/spin cycles.
• A worn or cracked hose can cause water leaks under the machine.
• Blocked or collapsed hoses can contribute to slow or incomplete draining.
• Compatible replacement for the OEM pump hose connection on qualifying LG washers.

• One pump hose (single hose as shown)

• Disconnect power and turn off water supply before beginning any repairs.
• Confirm correct routing and secure clamps when installing to prevent leaks.
• Inspect adjacent clamps and fittings for wear; replace if corroded or damaged.