Wm-16220Fd Parts

This pump hose routes washer tub water to the drain pump, helping remove wash water during the drain cycle. Replace a cracked or clogged hose to stop leaks and restore normal draining. What it does:

• Channels tub water to the drain pump so the washer can expel water during drain/spin cycles.
• A worn or cracked hose can cause water leaks under the machine.
• Blocked or collapsed hoses can contribute to slow or incomplete draining.
• Compatible replacement for the OEM pump hose connection on qualifying LG washers.

• One pump hose (single hose as shown)

• Disconnect power and turn off water supply before beginning any repairs.
• Confirm correct routing and secure clamps when installing to prevent leaks.
• Inspect adjacent clamps and fittings for wear; replace if corroded or damaged.

This inlet valve assembly controls water flow into the appliance, restoring proper fill operation and helping prevent leaks when the original valve fails. Designed as a direct replacement part for affected models. What it does:

• Opens and closes water flow to start and stop appliance filling
• Works with the appliance's control system to deliver the correct fill volume
• Stops water flow when closed to help prevent overfilling and leaks
• Commonly replaces valves that drip, won't fill, fill continuously, or trigger fill-related error codes

• Shut off water supply and unplug the appliance before starting any work
• Drain remaining water from hoses and remove pressure before disconnecting plumbing
• Basic hand tools required; keep track of mounting hardware and gaskets
• After installation, restore power and water, then test for proper fill and leaks

This clamp assembly secures a hose or component to its mounting point to help prevent leaks and reduce vibration. It replaces a worn or broken clamp so the connection stays tight and stable. What it does:

• Secures hoses, lines, or parts to their mounting points to maintain a sealed connection
• Helps reduce vibration and movement that can cause wear or noise
• Restores proper fit where a cracked, bent, or missing clamp allows leaks or misalignment
• Simple, direct replacement—matches the OEM attachment function

• Disconnect power and water before servicing to avoid shock or flooding
• Inspect mating surfaces and hose condition; replace hose if damaged before installing clamp
• Use pliers or a screwdriver as needed; tighten to a snug fit—do not over-tighten
• Follow the appliance's service manual for disassembly/reassembly guidance and safety

This locker hook secures the appliance door or access panel, restoring proper latching and preventing accidental openings. Durable molded construction matches original fit for reliable everyday use and quick replacement. What it does:

• Replaces a worn, broken, or missing door latch hook to restore secure closure
• Helps stop doors or panels from popping open during operation or transport
• Eliminates rattling or misalignment caused by a damaged hook
• Fits into the original mounting location to maintain factory fit and function

• One locker hook

• Basic hand tools typically required; disconnect power or unplug the appliance before starting
• Inspect surrounding trim and fasteners; replace any damaged screws or clips for proper fit
• Tighten fasteners securely but avoid overtightening plastic components

A replacement holder assembly that secures and supports internal components for proper alignment and operation. Restores stable mounting where the original bracket is cracked, bent, or broken so the appliance runs quietly and reliably. What it does

• Provides a secure mounting point for internal parts that rely on a fixed support
• Prevents rubbing, misalignment, and excess vibration caused by a damaged holder
• Helps restore correct component positioning to improve part interaction and operation
• Commonly used when the original bracket is cracked, worn, or no longer holds parts firmly

• One holder assembly

• Disconnect power before starting any repair; shut off water supply if the repair requires opening plumbing
• Basic hand tools typically required; handle clips and tabs gently to avoid damage
• Inspect adjacent components for wear and replace if needed for a long-lasting repair

This door boot gasket forms the flexible seal between the outer tub and cabinet opening on a front-load washer to keep wash water contained. Replace a torn or moldy boot to stop leaks and lingering odors.

• Creates a watertight seal between the outer tub and the door opening
• Flexes with drum movement to maintain a reliable barrier during wash and spin
• Helps resolve leaks at the door, visible rips or cracks, water on the floor after a cycle, and musty smells that persist after cleaning

• Unplug the washer and turn off water supply before servicing
• Remove the front panel as needed; note the boot's orientation before removal
• Clean mounting grooves; seat the new boot evenly all the way around and secure clamps firmly
• Run a quick cycle to check for leaks after reassembly

This bellows is the flexible door boot seal that helps keep water contained in the washer tub and maintains a watertight seal around the front-load door. It replaces a damaged or leaking door boot to reduce leaks and restore proper sealing. What it does:

• Forms a flexible, watertight seal between the washer door and tub to help prevent leaks
• Keeps laundry water inside the drum during wash and rinse cycles
• Helps maintain drum pressure balance and proper door closing
• Commonly replaced when cracked, torn, or permanently deformed

• One bellows

• Recommended for front-load washers; fit with your model before ordering
• Typical replacement requires removing the outer and/or inner door trim and detaching clamp(s)
• Disconnect power and water supply before beginning any repair to avoid injury

The NOISE FILTER ASSEMBLY is an OEM part for LG washing machines. It is a component designed to minimize vibrations and reduce noise emanating from the washer during operation. Proper noise damping is important for smooth functionality without disturbance.

Causes of a bad noise filter assembly can include cracks or tears developing over extended use. Physical damage from impact could also compromise its noise-blocking abilities. 

Symptoms of a bad noise filter assembly include:

• Loud banging or clanking noises during wash and spin cycles
• Excessive vibrations felt through the washer cabinetry 
• Increased stress on other components from inadequate dampening
• Premature wear of suspension components like legs and runners

Replace yours today with this genuine OEM LG part to restore a quiet wash experience. This replacement assembly ensures optimum vibration control. It is also compatible with Sears/Kenmore models.

This filter assembly replaces the water/ice filter housing and valve connections in compatible refrigerators to restore proper water flow to the dispenser and icemaker. It helps stop leaks and resolve low or no-water flow when the housing is faulty. What it does

• Replaces the internal filter housing and inlet/outlet connections that route water to the dispenser and icemaker.
• Restores normal water flow and pressure when a cracked or damaged housing causes leaks or restricted flow.
• Helps prevent leaks that can occur from worn seals or damaged fittings in the filter assembly area.
• Can resolve symptoms such as reduced dispenser flow, intermittent water flow to the icemaker, or visible leaks near the filter area.

• One filter assembly (housing and associated valve/connectors) as shown

• Turn off the refrigerator water supply and unplug the appliance before beginning work.
• Relieve system pressure by dispensing water after shutoff and have towels ready to catch residual water.
• Inspect and tighten all connections; replace any O-rings or seals if specified by OEM instructions.
• After installation, turn the water back on, check for leaks, and flush several liters through the dispenser per manufacturer guidance before use.

The washer Hose Retainer Holder Clip is an OEM part that mounts behind the control panel on LG front-loading washers. It positions water supply hoses to prevent kinks or stress that leads to leaks over time. 

Causes of a failed clip include fatigue from years of front-load vibration and damage from any installation or repair work behind the control panel.

Symptoms of an insufficient hose retainer clip include:

• Loose, misrouted, or flopping hoses behind the control panel
• Bulging or kinked hoses that restrict water flow
• Water leaks at hose connections

This OEM replacement clip is compatible with select Kenmore front-loaders.

This is a replacement screw used to secure internal components and assemblies. It restores proper fastening when original screws are stripped, loose, or missing. What it does

• Secures panels, brackets, or small assemblies to prevent rattling and misalignment
• Restores proper fit when original fasteners are worn, stripped, or lost
• Helps stop vibration-related noise from loose parts
• Matches OEM fastening locations and thread style for intended application

• Screw as shown

• Unplug the appliance or disconnect power before starting any repair
• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten until snug; avoid overtightening which can strip threads or crack plastic
• Keep small parts away from children and dispose of damaged fasteners

This flexible door boot gasket forms the watertight seal between the washer door and tub to keep water inside during cycles. Replaces a torn, stretched, or worn bellows to stop leaks and restore a secure door seal. What it does:

• Seals the washer door to prevent water from leaking during wash and rinse cycles.
• Compensates for movement between the door and tub while maintaining a watertight barrier.
• Commonly needed when the bellows shows visible tears, cracks, or heavy wear.
• Helps reduce water pooling and mildew buildup caused by gaps or pinholes.

• Disconnect power and water supply before starting any repair.
• Inspect the tub and door mating surfaces; clean before installing the new bellows for a proper seal.
• Some models use internal clamps or retaining rings—retainers must be reinstalled or replaced exactly as removed.