Wm3407hwa Parts

A replacement hose clamp that secures a flexible hose to its fitting to help prevent leaks and disconnections. Restores a tight, reliable seal so hoses stay seated during normal use. What it does:

• Holds a rubber or plastic hose firmly to a pump, valve or connection to prevent leaks.
• Helps stop hose pull-off that can cause water leaks or appliance interruptions.
• Commonly replaced when clamps are corroded, bent, cracked or missing.
• Works as a low-cost repair to restore a secure hose connection without replacing the hose assembly.

• Disconnect power to the appliance and shut off the water supply before servicing.
• Use the correct tool (slip-joint pliers for spring-style clamps or a screwdriver for screw-type clamps) and avoid pinching the hose.
• Inspect the hose and fitting for damage; replace the hose if it's cracked or excessively worn.
• After installing, restore power/water and run a short test cycle or check for leaks.

A molded water guide that routes dispenser water inside the refrigerator to the dispenser/ice area, helping direct flow and reduce splashing. Fits the factory mounting points for a clean, secure path for water. What it does

• Channels water from the inlet tubing toward the dispenser/ice assembly to prevent misdirected flow.
• Helps keep water from pooling or dripping inside the cabinet or on internal components.
• Common replacement when you see water on shelves, puddling near the dispenser, or reduced or misdirected dispenser flow.
• Preserves proper alignment of the dispenser plumbing to prevent kinks or strain on tubing.

• One water guide (single molded channel) as shown.

• Turn off the refrigerator and shut off the water supply before starting; disconnect power for safety.
• Remove interior panels or shelves as needed to access mounting points; keep fasteners for reassembly.
• Inspect adjoining tubing and seals for damage and replace any worn components to ensure a leak-free fit.
• After installation, restore power and water, then check carefully for leaks during an initial test dispense.

This door boot gasket forms the flexible seal between the outer tub and cabinet opening on a front-load washer to keep wash water contained. Replace a torn or moldy boot to stop leaks and lingering odors.

• Creates a watertight seal between the outer tub and the door opening
• Flexes with drum movement to maintain a reliable barrier during wash and spin
• Helps resolve leaks at the door, visible rips or cracks, water on the floor after a cycle, and musty smells that persist after cleaning

• Unplug the washer and turn off water supply before servicing
• Remove the front panel as needed; note the boot's orientation before removal
• Clean mounting grooves; seat the new boot evenly all the way around and secure clamps firmly
• Run a quick cycle to check for leaks after reassembly

The Pump Assembly is an OEM part for LG washing machines. It plays an important role in moving water into and out of the washer tub during operation cycles. 

Causes of pump assembly failure generally stem from normal wear and tear on internal components over time. Mineral buildup from hard water or sediment can also clog critical areas.

Symptoms of a bad pump assembly include:

• Incomplete or slow filling/draining of water 
• Strange noises emanating from within the washer tub
• Error codes related to water level or drainage issues
• Reduced washing or rinsing performance

This LG OEM replacement part is also compatible with some Kenmore models. 

This factory bolt assembly is a hardware fastener used to secure designated components within the appliance. Replacing a worn or missing bolt restores a tight, stable connection to help reduce vibration and noise while keeping parts properly aligned. What it does:

• Secures a component to its bracket, frame, or base
• Maintains alignment and stability of the assembly
• Helps minimize vibration and rattling when tightened correctly
• Common symptoms: missing or stripped bolt, loose connection, unusual vibration/noise, visible damage to the bolt head or threads

• Disconnect power and, if applicable, shut off water supply before servicing
• Support the component being fastened to prevent strain while removing/installing the bolt
• Start threads by hand to avoid cross-threading; tighten snugly per OEM guidance—do not overtighten
• Reinstall any washers, sleeves, or grommets in the original order if present

The Stator Assembly is an OEM part for LG washing machines. The stator assembly acts as the stationary component of the motor that drives the wash drum and basket. It converts alternating current into mechanical motion through electromagnetic induction, working together with the rotor to power the motor.

Causes of a bad stator assembly can include defects in the windings, bearing wear, or damage due to excessive heat.

Symptoms of a bad stator assembly include:

• The motor failing to start or run
• Abnormal noises coming from the transmission
• Vibration or shaking issues
• Inability to advance cycles

This OEM LG part is also compatible with some Kenmore models.

The LG Washer Door Hinge Assembly is an OEM component specially designed for LG brand laundry machines. This assembly includes the front-loading door hinges that allow the washer door to securely open and close.

Symptoms of a bad hinge assembly include:

• A door that falls off entirely or does not stay attached 
• Squeaks, squeals, or grinding noises coming from hinges
• Restricted or difficult door-swinging movement
• Detached or failing hinge pins allow the door to sag

Causes of a bad hinge assembly can include wear and tear from years of constant door swinging motions, corrosion buildup interfering with smooth operation, or damage from excessive weight loads improperly handled.

The NOISE FILTER ASSEMBLY is an OEM part for LG washing machines. It is a component designed to minimize vibrations and reduce noise emanating from the washer during operation. Proper noise damping is important for smooth functionality without disturbance.

Causes of a bad noise filter assembly can include cracks or tears developing over extended use. Physical damage from impact could also compromise its noise-blocking abilities. 

Symptoms of a bad noise filter assembly include:

• Loud banging or clanking noises during wash and spin cycles
• Excessive vibrations felt through the washer cabinetry 
• Increased stress on other components from inadequate dampening
• Premature wear of suspension components like legs and runners

Replace yours today with this genuine OEM LG part to restore a quiet wash experience. This replacement assembly ensures optimum vibration control. It is also compatible with Sears/Kenmore models.

This holder assembly secures and positions an internal component so the appliance operates quietly and reliably. It replaces a worn or broken holder to restore proper alignment and prevent loose parts from rubbing or vibrating. What it does:

• Provides a stable mounting point to keep an internal component correctly positioned
• Prevents movement that can cause noise, vibration, or rubbing
• Restores secure fit when an original holder is cracked, broken, or worn
• Helps maintain proper operation of the related mechanism by keeping parts aligned

• Disconnect power (and water if applicable) before starting any repair
• Use basic hand tools; avoid overtightening fasteners to prevent damage
• Inspect surrounding clips and mounting points and replace if damaged

This wiring harness connects the appliance's control or component circuits to restore reliable electrical connections and proper function. It replaces a damaged or worn harness to stop intermittent power, control errors, or non-working components. What it does:

• Carries electrical signals between the control board and sensors/components.
• Replaces frayed, burnt, or broken wires that cause intermittent operation or component failure.
• Helps resolve control board communication errors or circuits that won't power.
• Restores secure plug-and-play connections when original connector ends are damaged.

• One wiring harness, single

• Disconnect power (unplug or turn off breaker) before starting any repair.
• Route wires along existing clips and channels; avoid sharp edges and hot surfaces.

The washer Hose Retainer Holder Clip is an OEM part that mounts behind the control panel on LG front-loading washers. It positions water supply hoses to prevent kinks or stress that leads to leaks over time. 

Causes of a failed clip include fatigue from years of front-load vibration and damage from any installation or repair work behind the control panel.

Symptoms of an insufficient hose retainer clip include:

• Loose, misrouted, or flopping hoses behind the control panel
• Bulging or kinked hoses that restrict water flow
• Water leaks at hose connections

This OEM replacement clip is compatible with select Kenmore front-loaders.

This inlet hose connects the home water supply to the appliance so it can fill properly. It replaces a worn or leaking supply hose to restore safe, reliable water flow for normal cycles. What it does:

• Directs incoming water from the household supply to the appliance inlet valve
• Works with the appliance's inlet valve and fittings to allow proper fill and rinse actions
• Commonly replaces hoses that leak, spray, kink, or block water flow
• Helps stop slow fills or intermittent filling caused by damaged or deteriorated hoses

• One inlet hose

• Turn off water supply and disconnect power before starting work
• Inspect and replace any damaged O-rings or fittings; use approved replacement fittings if needed
• Hand-tighten connections, then snug with a wrench—avoid over-tightening to prevent damage
• After installation, restore water and power, run a short fill cycle, and check all connections for leaks

This cabinet cover is a direct-replacement outer panel that restores the appliance's finished look while protecting internal components from dust and debris. It helps keep the cabinet sealed and prevents exposure from a damaged or missing panel. What it does:

• Replaces a cracked, dented, or missing cabinet cover to restore appearance
• Shields internal parts and wiring from dust, spills, and foreign objects
• Reduces rattles and vibration caused by loose or damaged panels
• Helps preserve proper airflow pathways by keeping the cabinet closed

• Disconnect power to the appliance before starting any work.
• Handle edges carefully; metal panels can be sharp.
• Basic hand tools are typically required; keep screws and mounting hardware organized.