Wm3455h Parts

This replacement refrigerator door gasket seals the door to keep cold air inside, helping restore proper cooling and reduce frost, condensation, and energy loss from a damaged or worn seal. What it does:

• Creates an airtight seal around the refrigerator door to maintain internal temperature.
• Prevents warm air infiltration that can cause frost buildup and uneven cooling.
• Reduces condensation and helps improve compressor efficiency when sealing properly.
• Common symptoms of a failing gasket: visible cracks or gaps, cold air leaks, frost or moisture buildup, and higher energy use.

• Remove the old gasket and clean the door flange before installing the new seal.
• Press the gasket evenly into the door channel; some models use retaining clips or screws—model-specific instructions.
• Check that the gasket seats uniformly with the door closed and make minor adjustments as needed.

AC pump motor assembly replaces a failed pump drive to restore proper water removal. Direct-fit replacement restores pump operation to stop standing water, noisy pumping, or continuous filling issues in compatible LG machines. What it does:

• Drives the washer/dishwasher pump to move water out of the tub or through the circulation system.
• Restores proper drainage when a worn motor causes the unit to fail to pump water.
• Stops humming, grinding, or high-pitched noises caused by a failing pump motor.
• Helps prevent leaks or overflow caused by a non-operating pump (when pump seals and hoses are intact).

• Always unplug the appliance and shut off water supply before starting repairs.
• Access the pump from the front/bottom service panel; support the tub or cabinet as needed to avoid strain.
• Keep original wiring orientation and mounting hardware; transfer gaskets/seals or replace if damaged.
• After installation, run a test drain cycle to ensure proper operation before full reassembly.

A replacement hose clamp that secures a flexible hose to its fitting to help prevent leaks and disconnections. Restores a tight, reliable seal so hoses stay seated during normal use. What it does:

• Holds a rubber or plastic hose firmly to a pump, valve or connection to prevent leaks.
• Helps stop hose pull-off that can cause water leaks or appliance interruptions.
• Commonly replaced when clamps are corroded, bent, cracked or missing.
• Works as a low-cost repair to restore a secure hose connection without replacing the hose assembly.

• Disconnect power to the appliance and shut off the water supply before servicing.
• Use the correct tool (slip-joint pliers for spring-style clamps or a screwdriver for screw-type clamps) and avoid pinching the hose.
• Inspect the hose and fitting for damage; replace the hose if it's cracked or excessively worn.
• After installing, restore power/water and run a short test cycle or check for leaks.

This duct outlet directs a dryer's exhaust from the cabinet to the external vent, helping maintain proper airflow and reduce leaks. It replaces a damaged or worn outlet flange to restore safe venting. What it does:

• Channels dryer exhaust from the cabinet to the vent hose or duct
• Helps maintain proper airflow for efficient drying
• Prevents exhaust leaks that can cause poor performance or odors
• Reduces rubbing/interference that can create noise when damaged

• One duct outlet

• Disconnect power before servicing; for gas dryers, turn off the gas supply and disconnect per local codes
• Use basic hand tools; avoid bending the outlet flange to prevent cracks
• Verify a secure seal with the vent hose after installation and test operation

This hinge spring restores proper tension to the door so it opens and closes smoothly and stays aligned. Replacing a fatigued spring helps prevent sagging or slamming and supports a consistent, reliable door close.

• Provides the return tension/counterbalance for the door hinge mechanism
• Assists smooth opening/closing and helps the door stay properly aligned when latched
• Helps maintain consistent closing force over time
• Failure symptoms include: door drops quickly, won't stay aligned or fully closed, weak/squeaking spring action

• Disconnect power before service; allow any hot surfaces to cool
• The hinge and spring are under tension—support the door and release/install tension carefully
• Note spring orientation and hole positions before removal; match them on installation
• Access may require removing trim or the door; keep fasteners organized for reassembly

This bellows is the flexible door boot seal that helps keep water contained in the washer tub and maintains a watertight seal around the front-load door. It replaces a damaged or leaking door boot to reduce leaks and restore proper sealing. What it does:

• Forms a flexible, watertight seal between the washer door and tub to help prevent leaks
• Keeps laundry water inside the drum during wash and rinse cycles
• Helps maintain drum pressure balance and proper door closing
• Commonly replaced when cracked, torn, or permanently deformed

• One bellows

• Recommended for front-load washers; fit with your model before ordering
• Typical replacement requires removing the outer and/or inner door trim and detaching clamp(s)
• Disconnect power and water supply before beginning any repair to avoid injury

This door gasket seals the refrigerator door to keep cold air in and maintain consistent temperatures. Replaces a worn or damaged seal to help reduce energy loss, frost buildup, and moisture inside the compartment. What it does:

• Creates an airtight seal between the door and cabinet to retain cold air.
• Helps prevent warm air infiltration that can cause temperature swings and food spoilage.
• Reduces condensation, frost buildup, and excess cycling of the compressor.
• Restores proper door closing and helps improve overall cooling efficiency.

• High-level swap: remove the old gasket and press or screw the new gasket into the door channel per OEM instructions.
• Inspect mounting channel and hinge alignment before installation; realign door if it does not seat evenly.
• If gasket appears loose after installation, warm gently and refit to improve sealing.
• Disconnect power only if instructed by the OEM for access; otherwise follow basic electrical safety and wear gloves as needed.

This rear cover replaces the cabinet back panel that protects internal components and helps maintain proper airflow. Restores enclosure integrity and reduces noise or debris entry when the original cover is cracked, warped, or missing. What it does:

• Shields motors, wiring and controls from dust, lint and accidental contact.
• Directs airflow path and helps avoid airflow-related performance issues.
• Reduces vibration noise caused by loose or damaged back panels.
• Prevents small objects from entering the appliance rear and creating hazards.

• One rear cover (cabinet back) as shown.

• Disconnect power (unplug or shut off breaker) before attempting any repairs.
• Access requires moving the appliance and removing exterior fasteners—keep track of screws and clips.
• Inspect surrounding seals and mounting points; replace any damaged hardware to ensure a secure fit.

This door inner frame is the replacement inner panel frame that supports the door liner and trim, restoring proper fit and appearance. It helps keep the door assembly aligned and finished for normal operation and seal integrity. What it does:

• Provides structural support for the door liner and attached trim pieces
• Restores correct alignment and fit of the door assembly
• Helps maintain a proper door seal and reduces drafts or uneven closing
• Replaces cracked, warped, or cosmetically damaged inner door framing

• One door inner frame

• Disconnect power to the appliance before starting any door repair
• Removal typically requires taking off door trim and inner liner; keep fasteners organized
• Inspect door gasket, hinges, and hardware while replacing the frame; replace any damaged hardware