Wm3499hva Parts

A molded water guide that routes dispenser water inside the refrigerator to the dispenser/ice area, helping direct flow and reduce splashing. Fits the factory mounting points for a clean, secure path for water. What it does

• Channels water from the inlet tubing toward the dispenser/ice assembly to prevent misdirected flow.
• Helps keep water from pooling or dripping inside the cabinet or on internal components.
• Common replacement when you see water on shelves, puddling near the dispenser, or reduced or misdirected dispenser flow.
• Preserves proper alignment of the dispenser plumbing to prevent kinks or strain on tubing.

• One water guide (single molded channel) as shown.

• Turn off the refrigerator and shut off the water supply before starting; disconnect power for safety.
• Remove interior panels or shelves as needed to access mounting points; keep fasteners for reassembly.
• Inspect adjoining tubing and seals for damage and replace any worn components to ensure a leak-free fit.
• After installation, restore power and water, then check carefully for leaks during an initial test dispense.

This drawer panel assembly replaces a worn, cracked, or damaged drawer front to restore the appliance's appearance and allow the drawer to open and close correctly. It provides a finished front surface and mounting location for the drawer handle. What it does

• Replaces a damaged or cracked drawer front so the appliance looks and functions like new
• Restores the handle and latch mounting points for secure opening and closing
• Helps correct a misaligned or loose drawer face that won't sit flush
• Useful for cosmetic repair after impact, deep scratches, or panel breakage

• Disconnect power to the appliance before starting any repair
• Remove the drawer and any retaining screws or clips to access the panel
• Retain original mounting hardware; transfer screws, clips, or trim pieces as needed
• Align tabs/clips carefully during reinstallation to avoid damaging mounting points

This protective cover shields internal components and wiring from dirt, moisture and accidental contact, helping keep the appliance safe and functioning properly. It's a small replacement panel that restores the appliance's factory protection. What it does:

• Covers and protects internal parts and wiring from debris and accidental impact
• Prevents loose components from rattling or shifting during operation
• Helps maintain proper spacing and alignment of nearby panels and clips
• Addresses symptoms like visible damage, missing cover, exposed wiring, or unusual noise from loose trim

• Disconnect power before starting any repair to avoid shock or injury
• Typically secures with clips or a few screws; use basic hand tools and take care not to strip fasteners
• Inspect mounting tabs and surrounding trim for damage; replace any broken clips before reassembly

This tub cover replaces the outer trim that surrounds the washer tub to protect internal components and provide a finished appearance. It restores a snug seal and helps keep water and debris away from moving parts. What it does:

• Covers and protects the outer edge of the washer tub to reduce debris intrusion and wear
• Helps maintain proper alignment and spacing between the tub and cabinet trim
• Restores the washer's finished appearance if the original cover is cracked, warped, or missing
• Can reduce noise caused by loose or damaged tub trim contacting other components

• One replacement tub cover

• Basic hand tools may be required; disconnect power and water before beginning
• Inspect surrounding seals and fasteners; replace any damaged clips or screws for a secure fit
• Handle carefully to avoid scratching the finish during installation

This locker hook secures the appliance door or access panel, restoring proper latching and preventing accidental openings. Durable molded construction matches original fit for reliable everyday use and quick replacement. What it does:

• Replaces a worn, broken, or missing door latch hook to restore secure closure
• Helps stop doors or panels from popping open during operation or transport
• Eliminates rattling or misalignment caused by a damaged hook
• Fits into the original mounting location to maintain factory fit and function

• One locker hook

• Basic hand tools typically required; disconnect power or unplug the appliance before starting
• Inspect surrounding trim and fasteners; replace any damaged screws or clips for proper fit
• Tighten fasteners securely but avoid overtightening plastic components

A replacement holder assembly that secures and supports internal components for proper alignment and operation. Restores stable mounting where the original bracket is cracked, bent, or broken so the appliance runs quietly and reliably. What it does

• Provides a secure mounting point for internal parts that rely on a fixed support
• Prevents rubbing, misalignment, and excess vibration caused by a damaged holder
• Helps restore correct component positioning to improve part interaction and operation
• Commonly used when the original bracket is cracked, worn, or no longer holds parts firmly

• One holder assembly

• Disconnect power before starting any repair; shut off water supply if the repair requires opening plumbing
• Basic hand tools typically required; handle clips and tabs gently to avoid damage
• Inspect adjacent components for wear and replace if needed for a long-lasting repair

This sensor assembly replaces a failed sensing unit to restore reliable condition monitoring and proper control signals for the appliance. Fits as the full sensor module used by the factory to detect operating conditions. What it does

• Detects operating conditions and sends signals to the control board so the appliance can run correct cycles.
• Helps address symptoms like error codes related to sensing, erratic or inconsistent cycles, or unexpected temperature/performance changes.
• Interfaces with existing wiring harness and mounting points to restore factory sensing functions.
• Functions as the OEM-specified replacement sensor module for systems that require a full sensor assembly swap.

• One complete sensor assembly as shown.

• Disconnect power before attempting replacement to avoid shock or damage.
• Handle the sensor and connectors carefully; avoid pulling on wiring or touching sensing elements.
• Match connector orientation and mounting locations to ensure proper fit and signal routing.

This door boot gasket forms the flexible seal between the outer tub and cabinet opening on a front-load washer to keep wash water contained. Replace a torn or moldy boot to stop leaks and lingering odors.

• Creates a watertight seal between the outer tub and the door opening
• Flexes with drum movement to maintain a reliable barrier during wash and spin
• Helps resolve leaks at the door, visible rips or cracks, water on the floor after a cycle, and musty smells that persist after cleaning

• Unplug the washer and turn off water supply before servicing
• Remove the front panel as needed; note the boot's orientation before removal
• Clean mounting grooves; seat the new boot evenly all the way around and secure clamps firmly
• Run a quick cycle to check for leaks after reassembly

The Pump Assembly is an OEM part for LG washing machines. It plays an important role in moving water into and out of the washer tub during operation cycles. 

Causes of pump assembly failure generally stem from normal wear and tear on internal components over time. Mineral buildup from hard water or sediment can also clog critical areas.

Symptoms of a bad pump assembly include:

• Incomplete or slow filling/draining of water 
• Strange noises emanating from within the washer tub
• Error codes related to water level or drainage issues
• Reduced washing or rinsing performance

This LG OEM replacement part is also compatible with some Kenmore models. 

The NOISE FILTER ASSEMBLY is an OEM part for LG washing machines. It is a component designed to minimize vibrations and reduce noise emanating from the washer during operation. Proper noise damping is important for smooth functionality without disturbance.

Causes of a bad noise filter assembly can include cracks or tears developing over extended use. Physical damage from impact could also compromise its noise-blocking abilities. 

Symptoms of a bad noise filter assembly include:

• Loud banging or clanking noises during wash and spin cycles
• Excessive vibrations felt through the washer cabinetry 
• Increased stress on other components from inadequate dampening
• Premature wear of suspension components like legs and runners

Replace yours today with this genuine OEM LG part to restore a quiet wash experience. This replacement assembly ensures optimum vibration control. It is also compatible with Sears/Kenmore models.

This factory bolt assembly is a hardware fastener used to secure designated components within the appliance. Replacing a worn or missing bolt restores a tight, stable connection to help reduce vibration and noise while keeping parts properly aligned. What it does:

• Secures a component to its bracket, frame, or base
• Maintains alignment and stability of the assembly
• Helps minimize vibration and rattling when tightened correctly
• Common symptoms: missing or stripped bolt, loose connection, unusual vibration/noise, visible damage to the bolt head or threads

• Disconnect power and, if applicable, shut off water supply before servicing
• Support the component being fastened to prevent strain while removing/installing the bolt
• Start threads by hand to avoid cross-threading; tighten snugly per OEM guidance—do not overtighten
• Reinstall any washers, sleeves, or grommets in the original order if present