Wm36708av Parts

This clamp assembly secures a hose or tubing connection to maintain a watertight seal and reduce vibration. Replacing a worn or damaged clamp helps stop leaks and prevents hoses from slipping loose during operation. What it does:

• Holds a hose or tube firmly in place to maintain proper sealing at the connection point.
• Prevents leaks caused by loose, cracked or corroded clamps.
• Reduces vibration and rattling from unsecured hoses.
• Common symptom: visible leaking, water pooling, or a loose hose connection.

• Disconnect power and shut off water supply before starting any repair.
• Use the correct pliers or screwdriver for the clamp type; avoid damaging the hose.
• Inspect the mating hose and seal; replace any cracked or hardened hoses before reinstalling.
• Do not overtighten—tighten just enough to secure the hose without cutting or deforming it.

A replacement balance weight that helps stabilize the washer drum during spin cycles to reduce vibration and noise. Restores proper weight distribution so the washer runs more quietly and reliably. What it does:

• Counters drum imbalance to reduce shaking and excessive movement during spins
• Helps minimize noise caused by uneven loads
• Preserves drivetrain components by reducing stress from heavy vibration
• Supports consistent spin performance and load stability

• Disconnect power and water supply before starting any repairs
• Handle carefully—weights can be heavy and require a helper or proper lifting technique
• Follow the washer's service manual for mounting location, orientation, and fastener torque
• After installation, run a test spin with a small load to reduce vibration

This multi wiring harness connects control circuitry to multiple components, restoring reliable electrical pathways for proper operation. It replaces a damaged or frayed harness to help eliminate intermittent power, unresponsive controls, or component failures caused by wiring faults. What it does

• Routes power and signals between the control board and several appliance components.
• Re-establishes secure electrical connections when original wires are broken, burnt, or corroded.
• Can address symptoms such as intermittent operation, components not receiving power, or erratic behavior tied to wiring faults.
• Uses OEM-style connectors and wiring lengths to match factory routing for a proper fit.

• One multi wiring harness as shown

• Always disconnect power (unplug or shut off breaker) before servicing the appliance.
• Handle connectors by the housings—do not pull on wires—and ensure all plugs fully seat with audible clicks.
• Route the harness following original wire paths and secure with existing clips or ties to prevent contact with moving or hot parts.

This connector hose replaces the appliance's water connection to restore secure water flow and reduce the risk of leaks or interrupted dispenser/ice-maker operation. It's a direct replacement for a damaged or leaking supply connector. What it does:

• Connects the household water supply to the appliance's internal water valve or dispenser.
• Restores reliable water flow when a cracked, split, or collapsed hose prevents proper delivery.
• Reduces water leakage caused by worn or damaged connector ends and seals.
• Commonly needed when you see visible leaks, no water to the dispenser/ice maker, or a loose/broken hose connection.

• Turn off water supply and unplug the appliance before replacing the hose to avoid electric shock or water damage.
• Use proper clamps and fittings; make sure connections are seated and tightened just enough to stop leaks—do not overtighten.
• After installation, restore power and water, then check all connections carefully for leaks. Replace immediately if the hose or fittings show signs of damage.

A replacement hose clamp that secures a flexible hose to its fitting to help prevent leaks and disconnections. Restores a tight, reliable seal so hoses stay seated during normal use. What it does:

• Holds a rubber or plastic hose firmly to a pump, valve or connection to prevent leaks.
• Helps stop hose pull-off that can cause water leaks or appliance interruptions.
• Commonly replaced when clamps are corroded, bent, cracked or missing.
• Works as a low-cost repair to restore a secure hose connection without replacing the hose assembly.

• Disconnect power to the appliance and shut off the water supply before servicing.
• Use the correct tool (slip-joint pliers for spring-style clamps or a screwdriver for screw-type clamps) and avoid pinching the hose.
• Inspect the hose and fitting for damage; replace the hose if it's cracked or excessively worn.
• After installing, restore power/water and run a short test cycle or check for leaks.

A molded water guide that routes dispenser water inside the refrigerator to the dispenser/ice area, helping direct flow and reduce splashing. Fits the factory mounting points for a clean, secure path for water. What it does

• Channels water from the inlet tubing toward the dispenser/ice assembly to prevent misdirected flow.
• Helps keep water from pooling or dripping inside the cabinet or on internal components.
• Common replacement when you see water on shelves, puddling near the dispenser, or reduced or misdirected dispenser flow.
• Preserves proper alignment of the dispenser plumbing to prevent kinks or strain on tubing.

• One water guide (single molded channel) as shown.

• Turn off the refrigerator and shut off the water supply before starting; disconnect power for safety.
• Remove interior panels or shelves as needed to access mounting points; keep fasteners for reassembly.
• Inspect adjoining tubing and seals for damage and replace any worn components to ensure a leak-free fit.
• After installation, restore power and water, then check carefully for leaks during an initial test dispense.

This protective cover shields internal components and wiring from dirt, moisture and accidental contact, helping keep the appliance safe and functioning properly. It's a small replacement panel that restores the appliance's factory protection. What it does:

• Covers and protects internal parts and wiring from debris and accidental impact
• Prevents loose components from rattling or shifting during operation
• Helps maintain proper spacing and alignment of nearby panels and clips
• Addresses symptoms like visible damage, missing cover, exposed wiring, or unusual noise from loose trim

• Disconnect power before starting any repair to avoid shock or injury
• Typically secures with clips or a few screws; use basic hand tools and take care not to strip fasteners
• Inspect mounting tabs and surrounding trim for damage; replace any broken clips before reassembly

This small replacement hole cap covers unused access openings to restore a finished appearance and help keep out dust and debris. It's a simple, low-cost part that maintains appliance appearance and helps prevent contamination. What it does:

• Covers an open service or mounting hole to improve cosmetics
• Blocks dust, lint and small debris from entering the cabinet or enclosure
• Helps reduce drafts around service openings
• Prevents accidental contact with exposed fasteners or edges

• No special tools required; typically snaps or presses into place
• Secure fit before use
• If removing nearby panels, unplug the appliance or disconnect power first
• Replace any damaged retaining features before relying on the cap for protection

A replacement holder assembly that secures and supports internal components for proper alignment and operation. Restores stable mounting where the original bracket is cracked, bent, or broken so the appliance runs quietly and reliably. What it does

• Provides a secure mounting point for internal parts that rely on a fixed support
• Prevents rubbing, misalignment, and excess vibration caused by a damaged holder
• Helps restore correct component positioning to improve part interaction and operation
• Commonly used when the original bracket is cracked, worn, or no longer holds parts firmly

• One holder assembly

• Disconnect power before starting any repair; shut off water supply if the repair requires opening plumbing
• Basic hand tools typically required; handle clips and tabs gently to avoid damage
• Inspect adjacent components for wear and replace if needed for a long-lasting repair

This door boot gasket forms the flexible seal between the outer tub and cabinet opening on a front-load washer to keep wash water contained. Replace a torn or moldy boot to stop leaks and lingering odors.

• Creates a watertight seal between the outer tub and the door opening
• Flexes with drum movement to maintain a reliable barrier during wash and spin
• Helps resolve leaks at the door, visible rips or cracks, water on the floor after a cycle, and musty smells that persist after cleaning

• Unplug the washer and turn off water supply before servicing
• Remove the front panel as needed; note the boot's orientation before removal
• Clean mounting grooves; seat the new boot evenly all the way around and secure clamps firmly
• Run a quick cycle to check for leaks after reassembly

This holder assembly secures and positions an internal component so the appliance operates quietly and reliably. It replaces a worn or broken holder to restore proper alignment and prevent loose parts from rubbing or vibrating. What it does:

• Provides a stable mounting point to keep an internal component correctly positioned
• Prevents movement that can cause noise, vibration, or rubbing
• Restores secure fit when an original holder is cracked, broken, or worn
• Helps maintain proper operation of the related mechanism by keeping parts aligned

• Disconnect power (and water if applicable) before starting any repair
• Use basic hand tools; avoid overtightening fasteners to prevent damage
• Inspect surrounding clips and mounting points and replace if damaged

This drawer front assembly replaces a damaged or worn front panel to restore the appliance's appearance and proper drawer operation. It fits the specified LG drawer system and provides the finished exterior surface the drawer needs. What it does:

• Replaces the drawer front panel to restore proper drawer alignment and cosmetic appearance
• Provides a secure mounting surface for the drawer face and any attached trim or handle
• Helps stop rubbing, sticking, or misalignment caused by a cracked or warped front panel
• Restores a uniform exterior look when the original drawer front is dented, scratched, or broken

• One Drawer Panel Assembly (front panel) as shown

• Basic removal of the drawer and a few fasteners is usually required; keep hardware for reuse unless damaged
• Handle or trim may need to be transferred if not integrated; fit before final fastening
• Power off and empty the drawer before beginning work to avoid injury or damage

This inner door frame is the factory replacement trim piece that helps secure interior door components and restore a finished appearance. It replaces damaged or cracked inner door trim to keep the door assembly stable and looking like new. What it does:

• Replaces a cracked, warped or broken inner door frame or trim piece
• Provides mounting/support for interior door components and shelves
• Restores a proper fit and factory appearance to the door interior
• Helps prevent further damage to door-mounted parts from a loose or broken frame

• One (1) inner door frame

• Disconnect power to the appliance before starting any repair
• Remove door shelves, gasket and any clips or screws to access the inner frame
• Handle parts carefully to avoid scratching the finish; retain all fasteners for reassembly

This is a replacement screw used to secure internal components and assemblies. It restores proper fastening when original screws are stripped, loose, or missing. What it does

• Secures panels, brackets, or small assemblies to prevent rattling and misalignment
• Restores proper fit when original fasteners are worn, stripped, or lost
• Helps stop vibration-related noise from loose parts
• Matches OEM fastening locations and thread style for intended application

• Screw as shown

• Unplug the appliance or disconnect power before starting any repair
• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten until snug; avoid overtightening which can strip threads or crack plastic
• Keep small parts away from children and dispose of damaged fasteners