Wm3700hwa Parts

This dispenser assembly replaces a damaged or worn refrigerator ice and water dispenser housing to restore user access to chilled water and dispensed ice. It provides the mounting and user-facing components required for normal dispenser operation. What it does:

• Replaces the dispenser housing and bezel that guide water and ice to the user
• Restores proper alignment of the dispenser lever/actuator for reliable dispensing
• Helps stop leaks or dripping when the dispenser opening or funnel is cracked
• Works with internal valves and switches to permit normal dispense functions

• One dispenser assembly

• Disconnect power and shut off the refrigerator water supply before starting
• Remove the refrigerator door inner panel and any trim to access the dispenser module
• Handle plastic trim and tabs carefully to avoid breakage; use proper trim tools if available
• After installation, restore water, check for leaks, and test water/ice dispensing

This knob assembly replaces a damaged or missing control knob so you can securely and accurately set cooktop or oven controls. Durable replacement restores tactile grip and proper engagement with the control shaft. What it does:

• Replaces a cracked, melted, stripped, or loose control knob that won't turn or stay in position
• Provides correct spline engagement for consistent selection of heat or function settings
• Restores safe, predictable control response when adjusting temperature or burner level
• Helps prevent accidental slips or improper control input from worn knob surfaces

• One knob assembly

• Disconnect power to the appliance before servicing; for gas ranges also shut off the gas supply
• Pull the old knob straight off the control shaft; align splines and push the new knob fully onto the shaft
• If knob resists, verify correct orientation—do not force or hammer the part into place
• If the control shaft or switch is damaged, replace the underlying control/switch assembly rather than relying on the knob

This multi wiring harness connects control circuitry to multiple components, restoring reliable electrical pathways for proper operation. It replaces a damaged or frayed harness to help eliminate intermittent power, unresponsive controls, or component failures caused by wiring faults. What it does

• Routes power and signals between the control board and several appliance components.
• Re-establishes secure electrical connections when original wires are broken, burnt, or corroded.
• Can address symptoms such as intermittent operation, components not receiving power, or erratic behavior tied to wiring faults.
• Uses OEM-style connectors and wiring lengths to match factory routing for a proper fit.

• One multi wiring harness as shown

• Always disconnect power (unplug or shut off breaker) before servicing the appliance.
• Handle connectors by the housings—do not pull on wires—and ensure all plugs fully seat with audible clicks.
• Route the harness following original wire paths and secure with existing clips or ties to prevent contact with moving or hot parts.

This DC pump motor assembly drives the appliance pump to move and remove water during drain and circulation cycles. It restores pump operation so the washer/dishwasher can empty properly and avoid standing water. What it does:

• Powers the drain/recirculation pump to move water out of the tub during drain and wash cycles.
• Common repair when the appliance fails to drain, leaves standing water, or shows drain-related errors.
• Helps restore normal water flow for wash, rinse and drain sequences.

• Disconnect power (and water, if applicable) before servicing the appliance.
• Inspect hoses, filters and the pump housing for clogs before replacing the motor.
• Note connector orientation and mounting location; transfer gaskets/seals if the original must be reused.

This bolt assembly secures the washer's tub for transport, helping protect the suspension and internal components when moving the appliance. Replace lost or damaged shipping hardware so the drum stays locked and protected in transit.

• Locks the tub to minimize movement during transport or shipping
• Helps prevent damage to shocks, springs, hoses, and wiring while moving
• Replaces stripped, bent, or missing shipping bolts
• Use when relocating the appliance or returning it for service

• Unplug the appliance and turn off water before preparing to move it
• From the rear of the cabinet, thread the bolt into the designated shipping-bolt location and tighten until snug; do not overtighten
• Install all required shipping bolts for your model before transport; keep the unit upright while moving
• Remove all shipping bolts before operating the washer and save them for future moves

A replacement hose clamp that secures a flexible hose to its fitting to help prevent leaks and disconnections. Restores a tight, reliable seal so hoses stay seated during normal use. What it does:

• Holds a rubber or plastic hose firmly to a pump, valve or connection to prevent leaks.
• Helps stop hose pull-off that can cause water leaks or appliance interruptions.
• Commonly replaced when clamps are corroded, bent, cracked or missing.
• Works as a low-cost repair to restore a secure hose connection without replacing the hose assembly.

• Disconnect power to the appliance and shut off the water supply before servicing.
• Use the correct tool (slip-joint pliers for spring-style clamps or a screwdriver for screw-type clamps) and avoid pinching the hose.
• Inspect the hose and fitting for damage; replace the hose if it's cracked or excessively worn.
• After installing, restore power/water and run a short test cycle or check for leaks.

This holder assembly secures and positions internal components so the appliance's parts stay aligned and operate smoothly. Replacing a worn or broken holder helps stop rattling and restores proper fit where parts connect. What it does:

• Supports and locates adjacent components to maintain correct alignment
• Prevents excess movement that can cause noise or wear
• Helps ensure proper engagement of the associated trim or functional part
• Common symptom: loose, rattling, or misaligned components near the mounting area

• Designed to replace the original holder; fit with the part number before ordering
• Basic hand tools required; access panel removal may be necessary
• Disconnect power before beginning service to avoid shock or injury
• If clips or screws are damaged, replace them with equivalent hardware for a secure fit

The Power Cord Assembly is an OEM replacement part for LG front-loading washing machines. As the primary connection to household electricity, this cord safely delivers the required voltages to internal components.

Causes of a damaged or defective cord typically involve accidental cuts, abrasions or punctures accumulated over time. Repeated bending stresses during installations can prematurely crack insulation as well.

Symptoms of a problematic power cord include: 

• Inability to power "On" when plugged in  
• Tripped breakers or ground fault outlets
• Visible wire fraying or other signs of compromised integrity

This OEM assembly fits some Kenmore/Sears machines and protects against potential shock or fire hazards.

A molded water guide that routes dispenser water inside the refrigerator to the dispenser/ice area, helping direct flow and reduce splashing. Fits the factory mounting points for a clean, secure path for water. What it does

• Channels water from the inlet tubing toward the dispenser/ice assembly to prevent misdirected flow.
• Helps keep water from pooling or dripping inside the cabinet or on internal components.
• Common replacement when you see water on shelves, puddling near the dispenser, or reduced or misdirected dispenser flow.
• Preserves proper alignment of the dispenser plumbing to prevent kinks or strain on tubing.

• One water guide (single molded channel) as shown.

• Turn off the refrigerator and shut off the water supply before starting; disconnect power for safety.
• Remove interior panels or shelves as needed to access mounting points; keep fasteners for reassembly.
• Inspect adjoining tubing and seals for damage and replace any worn components to ensure a leak-free fit.
• After installation, restore power and water, then check carefully for leaks during an initial test dispense.

This tub assembly is the inner drum component for compatible front-load washers, providing the rotating basket that holds laundry during wash cycles for effective tumbling and water drainage. What it does

• Replaces the washer's inner drum that holds and tumbles clothes during wash and spin cycles.
• Restores proper rotation to reduce rubbing, grinding, or noisy operation caused by a damaged drum.
• Helps ensure proper water drainage and balanced spinning when the drum is intact and centered.
• Can resolve symptoms like loud thumping, scraping noises, or clothes catching on a damaged drum surface.

• Disconnect power and water supply before beginning any repair.
• Drum assemblies are heavy — get a helper and use proper lifting technique.
• Installation typically requires removing the washer cabinet and drive components; follow the OEM service manual or a step-by-step guide.

A replacement holder assembly that secures and supports internal components for proper alignment and operation. Restores stable mounting where the original bracket is cracked, bent, or broken so the appliance runs quietly and reliably. What it does

• Provides a secure mounting point for internal parts that rely on a fixed support
• Prevents rubbing, misalignment, and excess vibration caused by a damaged holder
• Helps restore correct component positioning to improve part interaction and operation
• Commonly used when the original bracket is cracked, worn, or no longer holds parts firmly

• One holder assembly

• Disconnect power before starting any repair; shut off water supply if the repair requires opening plumbing
• Basic hand tools typically required; handle clips and tabs gently to avoid damage
• Inspect adjacent components for wear and replace if needed for a long-lasting repair

This PCB assembly is the appliance's main electronic control board. It replaces a damaged or faulty control board to restore programmed cycles and electronic functions for models that use this OEM part number. What it does:

• Controls user interface inputs, cycle selection, and machine operation logic
• Manages power delivery to valves, motors, and sensors through relay and driver circuits
• Detects and responds to sensor signals to coordinate wash/dry/heating sequences
• Can stop or err if the board fails, causing no power, unresponsive controls, or erroneous error codes

• Disconnect power and water before beginning any repair
• Take photos or label wiring before disconnecting harnesses to ensure correct reassembly
• Handle the board by the edges and avoid static discharge; use an anti-static wrist strap if available

This door boot gasket forms the flexible seal between the outer tub and cabinet opening on a front-load washer to keep wash water contained. Replace a torn or moldy boot to stop leaks and lingering odors.

• Creates a watertight seal between the outer tub and the door opening
• Flexes with drum movement to maintain a reliable barrier during wash and spin
• Helps resolve leaks at the door, visible rips or cracks, water on the floor after a cycle, and musty smells that persist after cleaning

• Unplug the washer and turn off water supply before servicing
• Remove the front panel as needed; note the boot's orientation before removal
• Clean mounting grooves; seat the new boot evenly all the way around and secure clamps firmly
• Run a quick cycle to check for leaks after reassembly

This factory bolt assembly is a hardware fastener used to secure designated components within the appliance. Replacing a worn or missing bolt restores a tight, stable connection to help reduce vibration and noise while keeping parts properly aligned. What it does:

• Secures a component to its bracket, frame, or base
• Maintains alignment and stability of the assembly
• Helps minimize vibration and rattling when tightened correctly
• Common symptoms: missing or stripped bolt, loose connection, unusual vibration/noise, visible damage to the bolt head or threads

• Disconnect power and, if applicable, shut off water supply before servicing
• Support the component being fastened to prevent strain while removing/installing the bolt
• Start threads by hand to avoid cross-threading; tighten snugly per OEM guidance—do not overtighten
• Reinstall any washers, sleeves, or grommets in the original order if present