Wm3997hwa Parts

A replacement hose clamp that secures a flexible hose to its fitting to help prevent leaks and disconnections. Restores a tight, reliable seal so hoses stay seated during normal use. What it does:

• Holds a rubber or plastic hose firmly to a pump, valve or connection to prevent leaks.
• Helps stop hose pull-off that can cause water leaks or appliance interruptions.
• Commonly replaced when clamps are corroded, bent, cracked or missing.
• Works as a low-cost repair to restore a secure hose connection without replacing the hose assembly.

• Disconnect power to the appliance and shut off the water supply before servicing.
• Use the correct tool (slip-joint pliers for spring-style clamps or a screwdriver for screw-type clamps) and avoid pinching the hose.
• Inspect the hose and fitting for damage; replace the hose if it's cracked or excessively worn.
• After installing, restore power/water and run a short test cycle or check for leaks.

This NTC thermistor is a refrigerator temperature sensor that monitors cooling system temperature and helps the control board maintain proper operation. It replaces a failed sensor to restore accurate temperature sensing and reliable cycle control. What it does:

• Measures internal temperature and sends a changing resistance signal to the control board
• Helps the fridge adjust compressor/fan cycles for stable cooling
• Common symptom fix: erratic or incorrect temperatures, frequent cycling, or temperature-related error codes
• Works as the sensor used in evaporator/air temperature sensing circuits (model-dependent)

• One NTC thermistor sensor (wiring and connector as shown)

• Disconnect power before servicing to avoid shock or damage
• Handle the sensor and wiring gently; avoid kinking or stretching the lead wires
• Mount and route the sensor per the unit's service diagram so it contacts the intended location
• Verify sensor response with a multimeter (NTC resistance should change with temperature) or follow the manufacturer's service procedure

This replacement refrigerator door gasket seals the cabinet to keep cold air inside and maintain proper food temperature. It restores an effective seal to reduce frost buildup, prevent moisture leaks, and help the fridge run efficiently. What it does:

• Forms an airtight barrier between the door and cabinet to retain cold air
• Helps prevent frost and ice buildup in the fresh-food compartment
• Reduces moisture and condensation that can cause water pooling or food spoilage
• Can help reduce excessive run-time caused by a leaking door seal

• Remove all food and shelves from the door area before starting
• Inspect mounting channel and door edge for debris; clean before installing the new gasket
• Align and seat the gasket fully into the mounting channel; confirm an even seal around the door

A molded water guide that routes dispenser water inside the refrigerator to the dispenser/ice area, helping direct flow and reduce splashing. Fits the factory mounting points for a clean, secure path for water. What it does

• Channels water from the inlet tubing toward the dispenser/ice assembly to prevent misdirected flow.
• Helps keep water from pooling or dripping inside the cabinet or on internal components.
• Common replacement when you see water on shelves, puddling near the dispenser, or reduced or misdirected dispenser flow.
• Preserves proper alignment of the dispenser plumbing to prevent kinks or strain on tubing.

• One water guide (single molded channel) as shown.

• Turn off the refrigerator and shut off the water supply before starting; disconnect power for safety.
• Remove interior panels or shelves as needed to access mounting points; keep fasteners for reassembly.
• Inspect adjoining tubing and seals for damage and replace any worn components to ensure a leak-free fit.
• After installation, restore power and water, then check carefully for leaks during an initial test dispense.

This drawer panel assembly replaces a worn, cracked, or damaged drawer front to restore the appliance's appearance and allow the drawer to open and close correctly. It provides a finished front surface and mounting location for the drawer handle. What it does

• Replaces a damaged or cracked drawer front so the appliance looks and functions like new
• Restores the handle and latch mounting points for secure opening and closing
• Helps correct a misaligned or loose drawer face that won't sit flush
• Useful for cosmetic repair after impact, deep scratches, or panel breakage

• Disconnect power to the appliance before starting any repair
• Remove the drawer and any retaining screws or clips to access the panel
• Retain original mounting hardware; transfer screws, clips, or trim pieces as needed
• Align tabs/clips carefully during reinstallation to avoid damaging mounting points

This hose connector joins the water inlet hose to the appliance, restoring a secure, watertight feed for normal fill and wash cycles. Replaces a worn or damaged connection to stop leaks and ensure proper water flow. What it does:

• Connects the incoming water hose to the appliance inlet for stable water delivery
• Stops leaks caused by cracked, split, or loose connector fittings
• Helps restore normal fill behavior when a failed connector is preventing proper water flow
• Serves as a direct replacement for a damaged or corroded inlet connection

• Turn off and shut off the home's water supply and unplug the appliance before installing
• Remove the old connector and clean mating surfaces; inspect hose and clamps for wear
• Hand-start fasteners, then snug fittings—avoid over-tightening to prevent damage

This protective cover shields internal components and wiring from dirt, moisture and accidental contact, helping keep the appliance safe and functioning properly. It's a small replacement panel that restores the appliance's factory protection. What it does:

• Covers and protects internal parts and wiring from debris and accidental impact
• Prevents loose components from rattling or shifting during operation
• Helps maintain proper spacing and alignment of nearby panels and clips
• Addresses symptoms like visible damage, missing cover, exposed wiring, or unusual noise from loose trim

• Disconnect power before starting any repair to avoid shock or injury
• Typically secures with clips or a few screws; use basic hand tools and take care not to strip fasteners
• Inspect mounting tabs and surrounding trim for damage; replace any broken clips before reassembly

This tub cover replaces the outer trim that surrounds the washer tub to protect internal components and provide a finished appearance. It restores a snug seal and helps keep water and debris away from moving parts. What it does:

• Covers and protects the outer edge of the washer tub to reduce debris intrusion and wear
• Helps maintain proper alignment and spacing between the tub and cabinet trim
• Restores the washer's finished appearance if the original cover is cracked, warped, or missing
• Can reduce noise caused by loose or damaged tub trim contacting other components

• One replacement tub cover

• Basic hand tools may be required; disconnect power and water before beginning
• Inspect surrounding seals and fasteners; replace any damaged clips or screws for a secure fit
• Handle carefully to avoid scratching the finish during installation

A replacement holder assembly that secures and supports internal components for proper alignment and operation. Restores stable mounting where the original bracket is cracked, bent, or broken so the appliance runs quietly and reliably. What it does

• Provides a secure mounting point for internal parts that rely on a fixed support
• Prevents rubbing, misalignment, and excess vibration caused by a damaged holder
• Helps restore correct component positioning to improve part interaction and operation
• Commonly used when the original bracket is cracked, worn, or no longer holds parts firmly

• One holder assembly

• Disconnect power before starting any repair; shut off water supply if the repair requires opening plumbing
• Basic hand tools typically required; handle clips and tabs gently to avoid damage
• Inspect adjacent components for wear and replace if needed for a long-lasting repair

Note: This part is the outer frame only, it does not include the outer window. For the window, you have to order the complete door by model.

The NOISE FILTER ASSEMBLY is an OEM part for LG washing machines. It is a component designed to minimize vibrations and reduce noise emanating from the washer during operation. Proper noise damping is important for smooth functionality without disturbance.

Causes of a bad noise filter assembly can include cracks or tears developing over extended use. Physical damage from impact could also compromise its noise-blocking abilities. 

Symptoms of a bad noise filter assembly include:

• Loud banging or clanking noises during wash and spin cycles
• Excessive vibrations felt through the washer cabinetry 
• Increased stress on other components from inadequate dampening
• Premature wear of suspension components like legs and runners

Replace yours today with this genuine OEM LG part to restore a quiet wash experience. This replacement assembly ensures optimum vibration control. It is also compatible with Sears/Kenmore models.

This replacement connector hose routes water between the refrigerator water valve and the dispenser or ice maker, restoring reliable water flow and helping prevent leaks. It's a direct-fit service part used where the factory hose is worn or damaged. What it does

• Connects the refrigerator water valve to the dispenser or ice maker, providing a sealed water path.
• Restores proper water and ice delivery when a cracked or leaking hose causes reduced flow or pooling.
• Helps prevent leaks by replacing brittle, cracked, or split tubing and fittings.
• Works with the original fittings and routing used by the manufacturer for a secure connection.

• One replacement connector hose.

• Turn off and disconnect the refrigerator's water supply and power before starting.
• Verify orientation and routing match the original hose; avoid sharp bends or kinks.
• Tighten fittings securely but avoid over-tightening; inspect for leaks after reconnecting water.

The washer Hose Retainer Holder Clip is an OEM part that mounts behind the control panel on LG front-loading washers. It positions water supply hoses to prevent kinks or stress that leads to leaks over time. 

Causes of a failed clip include fatigue from years of front-load vibration and damage from any installation or repair work behind the control panel.

Symptoms of an insufficient hose retainer clip include:

• Loose, misrouted, or flopping hoses behind the control panel
• Bulging or kinked hoses that restrict water flow
• Water leaks at hose connections

This OEM replacement clip is compatible with select Kenmore front-loaders.