Wmh78019hz-1 Parts

This replacement cookware piece restores a missing or damaged pot or pan used with compatible Whirlpool cooking appliances, letting you safely resume everyday stovetop cooking with a correct-fit, OEM-style component. What it does:

• Replaces worn, damaged, or missing cookware used on compatible Whirlpool ranges or cooktops
• Provides a usable cooking surface for boiling, simmering, frying, and other stovetop tasks
• Helps eliminate symptoms like unusable or unstable cookware, excessive warping, or compromised nonstick surfaces
• Matches OEM form and function so controls and heat sources work as intended

• Only install when the appliance and cooktop are cool and power is disconnected
• Verify the part number and fit against your appliance before installation
• Follow the appliance owner's manual and OEM instructions for placement and use
• Do not use cookware with damaged bottoms or compromised nonstick surfaces; discard if safety is in question

This wire harness assembly connects electrical components to restore reliable power and signal routing in your appliance. It replaces a damaged or worn wiring assembly to help bring controls and functions back to normal operation. What it does:

• Re-establishes electrical connections between components so controls, lights, or motors can operate
• Replaces broken, burned, or frayed wiring that can cause intermittent operation or failure
• Helps stop flickering displays, unresponsive controls, or components that won't power on
• Reduces risk of shorts from exposed wiring when installed correctly

• Disconnect power (unplug or shut off breaker) before starting any repair
• Take photos of original routing and connector locations to ensure correct reassembly
• Do not attempt repair with damaged insulation or exposed conductors — replace the entire harness
• Ensure all connectors are fully seated and secure; avoid pulling on wires when positioning

This grill vent replaces the front vent trim that directs airflow from the oven cavity to the outside. Restores proper venting and helps maintain even cooking and safe appliance operation. What it does:

• Directs hot air and steam out of the oven cavity during operation
• Helps maintain consistent internal oven temperature for better cooking results
• Prevents exhaust from entering the control/console area
• Can reduce cooking odors and excessive heat buildup near the control panel

• Remove power to the appliance before servicing to avoid electrical shock
• Typical installation requires removing the oven door or control panel for access—follow the OEM service instructions
• Use proper tools and handle trim pieces carefully to avoid scratching finishes
• If corrosion or additional damage is present, inspect surrounding components and replace as needed

This mounting plate secures internal components to the appliance frame, restoring proper alignment and support for affected assemblies. It's a simple replacement that prevents excessive movement and helps stop rattles or loose parts. What it does

• Provides a stable anchor point for nearby components and assemblies
• Restores proper alignment to reduce rubbing, vibration, or unusual noises
• Replaces worn, bent, or missing plates that allow parts to shift
• Helps maintain safe, reliable operation by keeping components properly positioned

• One mounting plate

• Disconnect power to the appliance before beginning any service
• Basic hand tools typically required; follow the service manual for screw/fastener locations
• Inspect surrounding parts and fasteners; replace any damaged hardware as needed

This replacement air duct routes exhaust air from the dryer blower to the vent outlet, helping restore proper airflow and reduce heat buildup. Use this genuine-style duct when the original is cracked, warped, or leaking. What it does:

• Channels exhaust air from the blower assembly to the vent outlet for efficient drying
• Replaces damaged, cracked, or distorted ducts that cause leaks or reduced airflow
• Helps address symptoms such as poor airflow, longer dry times, or unusual noises from the dryer
• Restores a sealed airflow path to reduce internal heat accumulation

• Disconnect power (and gas supply, if applicable) before beginning any repair
• Follow the dryer service manual for panel removal and reassembly; keep screws and fasteners organized
• Inspect adjacent seals and gaskets and replace if worn to ensure a proper fit
• Handle plastic duct parts carefully to avoid cracking; ensure clearance so the duct is not pinched during reassembly

This replacement shield is a small protective cover that helps guard internal components from debris and direct contact, keeping your appliance operating safely and reliably. It restores the intended protection and fit when the original shield is damaged or missing. What it does:

• Covers and protects nearby wiring, sensors, or components from accidental contact and debris
• Helps maintain proper airflow/pathways where applicable to prevent interference
• Reduces risk of rubbing or chafing on wiring and parts that can cause failures
• Can stop rattling or vibration caused by a loose or broken cover

• One replacement shield as shown

• Disconnect power (and water if appliance requires) before beginning any repair
• Inspect surrounding clips and fasteners; replace any that are damaged to ensure a secure fit
• Use basic hand tools; avoid forcing the shield into place to prevent breakage

This resistor is an OEM electrical replacement that helps regulate current to a refrigerator/dryer appliance circuit so components operate reliably. Replacing a faulty resistor restores proper electrical control and can stop intermittent component failures. What it does

• Limits or regulates electrical current to a specific circuit so motors, heaters, or control circuits operate correctly
• Can cause an appliance component to run weakly, intermittently, or not at all when failed
• Commonly linked to symptoms such as component failure, intermittent operation, or related error codes
• Works as the direct replacement part for the original listed Whirlpool resistor

• One resistor

• Disconnect power to the appliance before attempting service to avoid shock
• Handle electrical connections carefully; ensure secure, correct reconnection before restoring power

This cabinet wrap is the outer covering that fits over the appliance cabinet to restore appearance and protect internal components. It replaces a damaged, dented, or worn outer panel for a clean, finished look. What it does:

• Provides an exterior cover for the appliance cabinet, concealing internal parts and insulation.
• Restores cosmetic appearance by covering dents, scratches, or rusted areas.
• Helps maintain proper airflow pathways and seals where applicable.
• Reduces exposure of internal components to dirt and moisture.

• One cabinet wrap (outer cabinet cover), as specified by the OEM part number.

• Installation may require removing panels, disconnecting power, and supporting the cabinet.
• Use appropriate hand tools; avoid sharp edges on the wrap and cabinet.
• Disconnect power to the appliance before beginning work to prevent electrical shock.

This complete door assembly replaces a damaged or non-sealing outer door to restore safe operation and appearance. It provides the full door unit used on compatible Whirlpool over-the-range microwave models. What it does:

• Replaces a cracked, dented, or cosmetically damaged outer door
• Restores proper door closure and sealing for normal microwave operation
• Replaces a door with damaged handle, trim, or viewing window
• Helps address issues where the door won't latch or align correctly

• One complete outer door assembly

• Disconnect power and verify microwave is fully de-energized before servicing
• Handle with care to avoid scratching the finish or damaging the viewing window