Woc54ecoaw02 Parts

A small replacement button plug that fills a control-panel or console opening and restores a finished appearance. Keeps panels sealed and prevents debris from entering unused holes. What it does:

• Covers unused control holes or mounting openings on consoles and panels
• Helps block dust, moisture, and grime from entering appliance internals
• Restores a consistent, finished look to the control surface
• Useful when a damaged or missing plug leaves an exposed opening

• One button plug (black)

• Typically snaps into place from the front of the panel; no special tools usually required
• Ensure the cavity is clean and free of debris before installing for a secure fit
• If the plug sits near electrical components, disconnect power to the appliance before servicing
• Verify fit against the opening before final installation; slight trimming is not recommended unless specified

This glass bracket secures the oven door glass to the door assembly, keeping the glass stable during normal use and helping maintain a proper seal. Replaces a worn or broken bracket to restore door stability and alignment. What it does:

• Holds the oven door glass in place so the door opens, closes, and seals correctly
• Prevents rattling, movement, or misalignment of the inner/outer door glass
• Helps maintain even heat containment by keeping the glass properly positioned
• Commonly replaced when the bracket is cracked, bent, or missing hardware

• Basic hand tools required; avoid over-tightening fasteners which can crack the glass
• Disconnect power to the appliance before removing or servicing the door
• Support the door and glass during removal to prevent dropping or breakage

This door hinge secures and pivots the refrigerator door so it opens and closes smoothly, restoring proper door alignment and seal for reliable cooling performance. What it does:

• Supports the refrigerator door and provides a smooth pivot point for opening and closing
• Helps maintain proper door alignment to ensure a tight seal and consistent internal temperature
• Can prevent or correct door sag, rubbing, or uneven gaps
• Reduces noise or sticking that occurs when the hinge is worn or damaged

• Disconnect power to the appliance before attempting repairs and work with the door supported to prevent dropping
• Use appropriate tools to remove and reinstall hinge fasteners; keep track of any washers or shims
• Verify door alignment and gasket seat after installation; adjust hinge position as needed before fully tightening
• If other hinge hardware is worn or damaged, replace those components to ensure proper function

This lamp holder secures and powers the oven/cabinet G4-base bulb so interior lighting works reliably and safely. It restores proper bulb contact and helps prevent flickering or intermittent lighting. What it does:

• Holds the G4-base light bulb in place and provides the electrical connection
• Restores interior lighting when the socket is loose, corroded, or damaged
• Helps stop flickering or intermittent on/off issues caused by a faulty holder
• Compatible with the oven/cabinet light assembly that uses a G4-style bulb

• Disconnect power to the appliance before servicing to avoid shock
• Allow the appliance and bulb to cool before touching components
• Inspect wiring and connectors; replace the holder if terminals are corroded or melted
• Use the correct G4 bulb type and wattage per the appliance manufacturer's instructions

This mounting bracket is a replacement support bracket that secures appliance components and keeps assemblies aligned for reliable operation. It restores proper fit and helps prevent rattling or movement from loose fittings. What it does:

• Secures panels or assemblies to the appliance frame to maintain proper alignment
• Reduces vibration and rattling caused by loose or damaged supports
• Restores mounting points that prevent sagging or separation of connected parts
• Helps ensure stable operation after repairs involving removed or replaced hardware

• Follow the appliance service manual for exact location and fastener torque
• Disconnect power (and gas if applicable) before beginning any repair
• Use appropriate tools and replace any damaged screws or clips with OEM-equivalent fasteners

This electronic control board manages and sequences the appliance's electrical functions, restoring reliable control and timed cycles when the original board fails. It replaces a faulty main control to help recover normal operation. What it does:

• Houses the appliance's control circuitry and processes user inputs and sensor signals
• Regulates timed cycles, relay switching, and display/indicator functions
• Common symptom: unresponsive controls or no display/readout
• Common symptom: appliance won't start, cycles erratically, or functions stop working

• Disconnect power before starting work to avoid shock or damage
• Observe electrostatic discharge (ESD) precautions and handle the board by its edges
• Follow the appliance service manual for panel removal and connector routing

This genuine replacement screw secures appliance components and restores proper fit where the original fastener has worn, stripped, or gone missing. It's a simple, reliable part to help stop rattling and keep panels and assemblies aligned. What it does:

• Fastens panels, brackets, or assemblies to maintain proper alignment and reduce vibration
• Replaces damaged, stripped, or missing screws to restore secure connections
• Helps eliminate rattling, loose trim, or gaps caused by a missing fastener
• Works where the appliance's original screw is required for proper fit

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Disconnect power and follow appliance safety procedures before accessing internal parts

This antenna and housing assembly (M2.0) replaces the factory antenna module and its outer housing to restore reliable wireless reception and secure mounting for the control electronics. It helps recover signal-dependent features and keeps internal components protected. What it does:

• Receives and routes wireless/control signals between the appliance electronics and external devices or modules
• Provides a secure, insulated housing to protect the antenna and associated wiring from damage
• Can resolve symptoms such as intermittent or lost wireless communication, unresponsive remote functions, or erratic control-panel connectivity
• Designed as a direct-fit assembly for the corresponding control harness and mounting points

• Disconnect power to the appliance before beginning any repair to avoid shock or damage
• Handle connectors and wiring gently; ensure mating connectors fully seat and locking tabs engage
• Keep screws and mounting hardware organized; verify the housing aligns with factory mounting bosses before tightening

A replacement mounting screw used to secure appliance panels and components. Restores a missing or stripped fastener so parts sit flush and stay in place for reliable operation. What it does

• Fastens panels, brackets, and trim to the appliance chassis
• Prevents rattling, loose panels, and misaligned parts when installed correctly
• Replaces missing or damaged screws to restore proper fit and function

• Disconnect power to the appliance before working on it
• Use the correct-size screwdriver or driver bit to avoid cam-out or stripping
• Install by hand until started, then snug; avoid over-tightening to prevent damage
• Keep removed hardware organized and compare to the replacement before installing

This is a threaded machine screw used to fasten appliance panels and components. It restores secure attachment points so panels, brackets, and assemblies stay firmly mounted and reduce rattling or misalignment. What it does

• Secures panels, brackets, or small components to the appliance chassis
• Restores loose or missing fasteners that cause vibration, rattling, or unsecured parts
• Provides the correct thread engagement to prevent stripped holes when installed properly
• Works wherever an 8-18 threaded screw is specified by the manufacturer

• Disconnect power to the appliance before beginning any repair.
• Use the correct screwdriver or nutdriver to avoid stripping the head.
• Do not overtighten; snug until secure to prevent damage to threads or panels.
• Follow manufacturer service instructions for safe disassembly.

The Inner Door Glass is an OEM part for Whirlpool microwaves. It forms the see-through window that allows for monitoring food as it cooks. The strengthened glass panel is designed to withstand prolonged exposure to steam and heat without issues.

Causes of bad inner door glass can include cracks or chips from accidental drops or impacts, or damage from cleaning chemicals or harsh scrubbing that compromise the glass integrity. 

Symptoms of a bad inner door glass include:

• Cracks or chips in the viewing surface
• Complete breakage leaving a hole in the door  
• Loose or improperly sealed glass panel
• Increased potential for leaks near door seals

This OEM Whirlpool replacement part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore microwaves.

The Microwave Inverter Board is an OEM part for Whirlpool brand microwaves. This board works with the magnetron to convert voltage and power the cooking elements. 

Causes of a bad inverter board can include failure of electronics over time, shorts or current leaks, or improper installation.

Symptoms of a bad inverter board include:

• The microwave will not power on or heat food properly  
• Sparking or burning smells are detected inside the microwave cavity
• The display console does not illuminate or function correctly
• Error codes are frequently displayed

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore models.