Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Stainless steel hex washer head screw for securing appliance panels, brackets, and trim. Replace missing, stripped, or corroded fasteners during repair.
Usually ships within 4 - 14 days
Secures washer tub and hoses to prevent leaks and noise. Replace if worn or broken to maintain proper alignment and seal. Verify fit with your model.
I did it Read more
Push-in plug button for top-load washers. Snaps into trim openings to cover unused holes and restore a clean finish. Replace if cracked or missing.
Silicon controlled rectifier (SCR) for washer power control boards. Replace if component is burnt, damaged, or failing to regulate current properly.
Secures the agitator assembly to the drive shaft in top-load washers. Replace if stripped, rusted, or missing during agitator repairs or removal.
Replaced the Coupling Pulsator, and the Pulsator (short spindle in the center of the washer). The only problem that I encountered was how to remove the short spindle in the center of the washer...my fabric softer is in the center and you need to open that, grab the middle and loosen by turning left. Once that is out you will use a 7/16th socket and remove the entire agitator. Most of the videos show that you pull that straight up to remove - not the short one. There is still a screw to remove.... Read more
Protects the washer's inner drum edge and prevents clothing from snagging on the tub lip. Replace if cracked, broken, or missing to avoid fabric damage.
This washer front panel assembly replaces a cracked, worn, or damaged console face. Restores appearance and provides housing for control buttons.
Dishwasher not powering on or experiencing electrical issues? This terminal block housing insulator protects wire connections. Simple repair part.
Mounting screw for dishwashers and washers. Used to secure internal components like pumps or transmissions. Replace if stripped, missing, or broken.
Fix washer overfilling and water spilling over the tub with this pressure switch. Simple 3-wire installation stops overflow issues. DIY-friendly repair.
I followed the rubber tubing attached to the outside of the washer tub and it was attached to the pressure switch. The switch is the only component in the system that could potentially fail, so I guessed that it had to be the culprit. I ordered the new one, it arrived in less than 36 hours, installed it, plugged the wires in just like the old one (only three wires) and voila, it now shuts off the water flow just like a new washer. Read more
Replace your washer's housing cover if the original is cracked, broken, or missing. This protective cover installs on the exterior to shield internal components.
This 1/4-20 screw secures the leg and platform assembly in your top-load washer. Replace missing or loose screws to restore proper balance.
OK kids, pay attention! This was my second attempt @ this repair. My first repair started leaking right away and had to be re-done about 6 months later. HERE IS THE PROBLEM!. In the video, you'll notice that (while putting it back together) when you put the square hole washer and split-ring over the shaft, they look to land atop the rubber seal, buy when you do this in real life, there is a gap between the seal and the washer. (This gap was close to a 1/4 inch). I THINK that the first time I... Read more
White right-hand console endcap for dryers. Replaces cracked, broken, or missing endcaps to restore the finished look of your control panel.
Self-leveling bracket for top-load washers. Mounts to the base to stabilize the unit. Replace if broken, bent, or missing to restore proper leveling.
Fix a washer that won't spin or agitates weakly with this motor and clutch kit. Solves pulsing motors and failed spin cycles. DIY repair takes 2-3 hours.
Handy Husband took off front of washing machine, unbolted motor then I held motor in place while he bolted on new one.He had to connect new wire harness.One wire was different color..orange instead of white with red stripe.He wrapped old hanging wires to steel bar supporting drum and new wire harness attached to inside where original used to be.He put on the new belt as well since old one was a bit old.He needed a phillips, metric tools..sockets, wrenches, wire cutters,a crimper, pliers and it... Read more
Conduit hose for top-load washers. Protects wiring connections inside the cabinet. Replace if cracked, split, or damaged to restore proper coverage.