Wrs315dhz Parts

The Grille is an OEM replacement part for Whirlpool refrigerators. It covers the gap between the bottom of the refrigerator and the floor, providing a clean and finished look to your kitchen. It helps protect the internal parts from dust and debris while also preventing small items from rolling underneath the appliance.

Symptoms of a bad toe grille include:

• Visible cracks or damage
• Discoloration or fading
• Missing pieces or gaps in the grille

A damaged or worn-out toe grille can occur due to regular use, accidental impacts, or general wear and tear over time. If you notice cracks, discoloration, or missing pieces on the toe grille, it may be time to replace it.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This compressor grommet is the rubber isolator that cushions the refrigerator's compressor at its mounting points. Replacing a worn grommet helps quiet vibration and rattling and reduces stress on refrigerant tubing for smoother, safer operation.

• Isolates the compressor from the base to damp vibration and humming
• Helps prevent metal-to-metal contact and rattling at the mounts
• Supports proper compressor alignment to reduce stress on tubing
• Helps with symptoms like loud buzzing/rattling or cracked/flattened rubber at the compressor feet

• Unplug the appliance and remove the rear access cover to reach the compressor area
• Support the compressor while removing hardware; replace the grommet in the same orientation
• Avoid kinking or stressing refrigerant lines; no sealed-system opening is required
• Tighten mount fasteners evenly and ensure the compressor sits level and isolated

The User Control and Display Board is an OEM replacement part for Whirlpool side-by-side refrigerators. It is the circuit board housed inside the control panel that operates and monitors all input and output functions. This includes powering the digital display, control buttons and receiving signals to regulate temperatures, ice & water dispensers, lighting and alarms. 

Causes of a bad user control board can include shorts or failures in the circuitry from repeated heating and cooling cycles over time. The board houses sensitive electronics prone to damage from moisture exposure or power surges. 

Symptoms of a faulty board are:

• Faulty temperature or moisture controls  
• Unresponsive or incorrectly functioning buttons
• Error codes or blinking lights on the display
• Issues with interior fridge lighting 

This Whirlpool OEM part is also compatible for use in Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, and some Kenmore side-by-side models.

The control box is an OEM component specifically designed for Whirlpool brand refrigerators. This control box houses the electronic components that operate and monitor refrigerator functions such as temperature settings, diagnostics, defrost cycles, and more.

Symptoms of a bad control box can include:

• Fault codes or error messages appearing on the display
• Temperature control issues where the refrigerator will not get cold enough 
• Failure of lights, ice maker, or other features to work properly

Causes of a bad control box are typically due to long-term usage and exposure to environmental conditions inside the refrigerator cabinet. This can lead to degraded electronic performance over time.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

This door bumper cushions the door against the frame to prevent metal-to-metal contact. Replacing a worn or missing bumper restores smooth, quieter closing and helps protect surfaces from chips, scuffs, and vibration.

• Absorbs impact where the door meets the cabinet/frame
• Reduces slamming noise and vibration during closing
• Helps protect paint, glass, and trim from wear
• Typical symptoms: missing/cracked bumper, loud clunk when closing, marks on frame, rattling

• Disconnect power and, if applicable, shut off gas/water; allow hot surfaces to cool
• Open the door to access the bumper location
• Remove the worn bumper and clean the contact area for proper seating
• Install the new bumper fully seated and aligned; test door operation

The Door Closer-Gravity is an OEM part for Whirlpool refrigerators. It is an assembly located on the top hinge side of the refrigerator door, responsible for providing controlled resistance when opening and closing the door.

Causes of a bad door closer can include worn or broken springs, a damaged sliding mechanism, or misaligned components from repeated use over time.

Symptoms of a bad door closer include:

• The door not staying open at the desired angle when accessing shelves and bins
• Excessive force required to open or close the door
• The door not fully closing or sealing against the cabinet

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement door bumper cushions the appliance door to reduce noise, prevent metal-on-metal contact, and protect the door finish. It restores smooth closing when the original bumper is worn, cracked, or missing. What it does:

• Cushions the door edge to prevent hard impacts and reduce slamming
• Dampens vibration and rattling that can occur when bumpers are worn
• Prevents metal-on-metal contact that can scratch or damage the door
• Helps keep the door aligned and closing smoothly

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Typically presses or snaps into a bumper mounting hole; remove the old bumper and press the new one into place.
• Inspect adjacent mounting holes and surrounding trim for damage while installing.

This humidity sensor housing holds and protects the fridge's humidity/control assembly, helping maintain proper humidity-sensing operation and reliable climate control. Designed to replace a cracked or damaged housing to restore proper sensor placement and protection. What it does:

• Secures and shields the humidity sensor and related control components
• Keeps the sensor correctly positioned for accurate humidity detection
• Prevents physical damage and moisture exposure to the sensor assembly
• Helps resolve symptoms like inaccurate humidity readings or loose sensor fit

• Disconnect power to the appliance before starting any repair
• Handle the humidity sensor carefully; remove and reinstall per manufacturer guidance
• Uses basic hand tools; refer to the service manual or OEM instructions for disassembly/reassembly steps
• Replace the affected components rather than reusing damaged parts

This replacement grille restores the vent trim at the front of the appliance, providing an even appearance and allowing proper airflow through the front vent area. Use it when the original grille is cracked, broken, or missing. What it does

• Covers and protects the front vent opening while directing airflow
• Replaces cracked, broken, warped, or cosmetically damaged trim
• Helps maintain a secure fit and prevents gaps that collect dust and debris
• Restores the appliance's finished appearance

• One replacement grille

• Disconnect power to the appliance before starting any work
• Remove the old grille by releasing clips or removing mounting screws as applicable
• Align the new grille and secure with the original fasteners or clips; do not force into place

Replacement screw that secures panels, brackets, and other components inside your appliance, keeping assemblies tight and aligned. Replace missing or stripped hardware to eliminate looseness, reduce vibration, and restore a solid, factory-fit hold.

• Fastens panels, brackets, trim, or internal components
• Helps maintain alignment and reduce rattling/vibration
• Replaces missing, loose, rusted, or stripped hardware
• Common signs: stripped head/threads, loose panel, buzzing/rattling noises

• Disconnect power before service; shut off gas/water if applicable
• Match to the original screw; start threading by hand to avoid cross-threading
• Use the correct driver size to prevent stripping
• Tighten snugly; do not overtighten. If it won't hold, inspect the receiving hole/clip

The Diffuser is an OEM component specifically designed for Whirlpool refrigerators. Located inside the refrigerator compartment's rear wall, it evenly distributes cool air flow throughout storage shelves.

Causes of a bad diffuser include cracks developing from constant air blowing over many years. Debris buildup may also obstruct optimum air distribution.

Symptoms of a bad diffuser include:

• Warm or cool spots inside the refrigerator   
• Reduced airflow felt at storage level vents  
• Visible cracks or breaks in the plastic structure
• Buildup of dust or particles on air passages

This OEM Whirlpool replacement diffuser ensures balanced interior temperatures. Its engineered vent design supports consistent air distribution along shelves. 

Replace yours if any symptoms surface. This part is also compatible with some GE, Crosley, and select Kenmore models. 

Replacement mounting screw that secures panels, brackets, or internal components to restore a solid fit and reduce movement. Simple, direct replacement for a missing, stripped, or corroded fastener to help maintain safe appliance operation. What it does:

• Holds trim, panels, brackets or control assemblies in place to prevent rattling and misalignment.
• Replaces stripped, rusted, or missing screws that can cause loose parts or vibration.
• Restores proper component alignment for safe, stable appliance performance.
• Small, inexpensive fix that prevents further wear to attached parts when properly installed.

• Use the correct screwdriver or bit to avoid stripping the head; match size to the screw.
• Do not overtighten — snug is sufficient to secure parts without damaging threads or components.
• Disconnect power to the appliance before working near controls or wiring.
• Keep removed screws organized during disassembly so all fasteners are replaced.

This door bumper cushions and stabilizes the appliance door to reduce noise and wear from slamming. It helps the door close smoothly and maintain proper alignment for reliable operation. What it does:

• Absorbs impact to prevent metal-on-metal contact and reduce slamming noise
• Helps the door sit evenly to improve latch engagement and sealing
• Reduces vibration and rattling during operation
• Simple replacement that restores proper door feel and alignment

• Disconnect power to the appliance before starting any repair
• Access the bumper by opening the door; some models may require removing the door or inner panel
• Press or snap the bumper into the locating hole or slot until secure; replace any retaining clips if present

The Door Handle is an OEM part for Whirlpool refrigerators. This sturdy handle serves as a convenient way to open and close the doors of your appliance. The door handle offers a comfortable grip and provides an easy way to access your refrigerator and freezer compartments. 

A bad door handle can occur due to excessive force, accidental impacts, or simply regular use over time. If you notice symptoms such as a loose or wobbly handle, difficulty in opening or closing the doors, or visible cracks or damage, it may be time to replace this part.

Symptoms of a bad door handle include:

• Loose or wobbly handle
• Difficulty in opening or closing the doors
• Visible cracks or damage

Restore your Whirlpool refrigerator by replacing the worn or damaged door handle with this genuine OEM part.

This OEM part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Color: White

This is a replacement 8-18 threaded screw used to secure panels and components on compatible Whirlpool appliances. It restores proper fastening where a missing or damaged screw causes loose parts or vibration. What it does

• Fastens panels, brackets, and small assemblies to the appliance frame
• Replaces stripped, corroded, or missing screws that cause rattling or loose components
• Helps maintain proper alignment of panels and controls for safer operation
• Suitable where an 8-18 threaded machine screw is specified by the manufacturer

• One replacement screw

• Disconnect power to the appliance before service to prevent shock or injury
• Use the correct driver to avoid stripping the screw head; do not force mismatched tools
• Tighten until snug — avoid over-tightening which can strip threads or crack plastic
• If replacing multiple fasteners, check mating threads and replace any damaged clips or anchors as needed