Wrt106tfdw 02 Parts

This replacement door gasket creates a tight seal around the appliance door to help maintain temperature control and reduce moisture or frost buildup. It restores proper door sealing for more consistent performance and energy efficiency. What it does:

• Seals the door opening to keep conditioned air inside and outside air out
• Helps prevent frost, ice buildup, and moisture damage in the cabinet area
• Reduces temperature fluctuations that can cause food spoilage or inefficient operation
• Common symptom: visible gaps at the door edge, warm spots, or excess condensation

• Remove the old gasket and clean the sealing surface before installing the new gasket
• Soften or warm the gasket if needed for easier fitting
• Press the gasket into the channel evenly; ensure corners and edges are fully seated

This refrigerator door gasket creates an airtight seal around the door to help keep cold in and moisture out, preserving food freshness and improving cooling efficiency. What it does:

• Seals the refrigerator door to prevent warm air entry and cold air loss
• Helps reduce frost buildup and condensation inside the refrigerator
• Can improve temperature stability and reduce run time when the seal is compromised
• Addresses symptoms such as visible gaps around the door, warm spots, or excess frost

• One refrigerator door gasket

• Inspect door frame for damage or debris and clean sealing surface before installing
• Warm the gasket slightly to make positioning easier; avoid open flames or excessive heat
• Work around the door edges to seat the gasket evenly; some fasteners or retainer channels may need to be adjusted

A small retainer clip that secures panels, hoses or wiring to keep components in place and reduce noise from loose parts. Replacing a worn or broken clip restores proper fit and helps prevent intermittent contact or rattling. What it does

• Secures trim, panels, hoses or wire harnesses to mounting points to prevent movement.
• Keeps components aligned so switches and seals engage correctly.
• Stops rattling or vibrating noises caused by loose parts.
• Helps prevent abrasion or chafing of wires and hoses by holding them away from edges.

• Install by snapping or sliding the clip into the factory mounting slot; use needle-nose pliers if needed.
• Power off and unplug the appliance before accessing internal parts.
• Inspect surrounding mounts and mating tabs for damage; replace if worn for a secure fit.
• If removal is difficult, apply a small amount of penetrating lubricant and work carefully to avoid breaking adjacent plastic.

This retaining clip secures trim, panels or small assemblies to keep parts aligned and prevent rattling. It's a simple replacement that restores a snug, stable fit where the original clip has broken or gone missing. What it does:

• Holds plastic or metal trim and panels in place to prevent gaps and movement
• Restores proper alignment and reduces vibration or rattling noises
• Keeps assembled components from shifting during normal use
• Useful when a damaged or missing clip causes loose or sagging parts

• One retaining clip

• Disconnect power and/or water to the appliance before beginning any repair
• Use needle-nose pliers or a flat screwdriver to remove the old clip and snap the replacement into place
• Verify the clip is fully seated and the panel/trim is secure before returning the appliance to service
• If the original clip required additional fasteners, retain and reuse them as needed

This electronic control board manages the appliance's user interface and cycle controls, restoring responsive buttons, accurate cycle selection, and timed operation. Replacing a faulty board fixes control and timing issues without replacing the entire console. What it does:

• Controls the front-panel buttons, touchpad signals, and cycle selection logic
• Sends start/stop and timing commands to motors, valves, and heaters
• Resolves intermittent operation or incorrect cycle behavior when board failure is confirmed

• One electronic control board

• Disconnect power at the source before inspecting or replacing the control to avoid shock
• Handle the board by the edges and avoid contact with components to prevent electrostatic damage
• Reassemble the console panels in the original order

This evaporator tray collects and channels defrost and condensation water away from the refrigerator evaporator, helping prevent leaks and ice buildup so the cooling system runs cleanly and reliably. What it does:

• Captures defrost and condensation water from the evaporator coil
• Directs water to the drain system to avoid pooling inside the cabinet
• Helps reduce ice buildup around the evaporator area
• Supports normal defrost operation and prevents water-related leaks or odors

• Disconnect power to the appliance before replacing parts to avoid electrical shock.
• Remove food and shelving as needed for safe access to the evaporator area.
• Inspect surrounding seals and drain tube for clogs or damage while replacing the tray.
• Handle carefully to avoid damaging delicate evaporator fins or nearby components.

This replacement cover restores the appliance's protective outer trim that shields internal controls and wiring from dirt and damage, keeping the unit looking finished and functioning safely. It fits where the original plastic or metal cover was mounted. What it does

• Protects control board, switches, and wiring from dust, moisture and accidental contact
• Helps keep the appliance appearance neat by covering mounting points and fasteners
• Prevents loose debris from entering internal components that can cause faults
• Common symptom: cracked, broken or missing cover exposing internal parts

• One replacement cover as shown

• Disconnect power to the appliance before beginning any work
• Remove required panels or bezels to access mounting screws
• Use appropriate hand tools; avoid over-tightening fasteners
• Inspect wiring and connectors before reassembly

Color: Bisque

Color: Black

This light lens is the replacement dome cover that protects and diffuses the refrigerator interior light, restoring even illumination and preventing direct bulb contact. It replaces cracked, yellowed or missing lenses. What it does

• Protects the interior light bulb from spills and contact
• Diffuses and softens the light for even illumination inside the compartment
• Stops rattling or loose cover noise when the original lens is broken or warped
• Helps prevent food or debris from hitting the bulb and causing premature failure

• One light lens (dome cover)

• Disconnect power to the appliance before beginning any work
• Typically installs by snapping into the light housing or fastening with one or two screws—retain mounting hardware if present
• Handle carefully to avoid cracking; replace if warped, chipped, or yellowed

Color: Black