Wrt111sfdm Parts

The Shelf Glass is an OEM component specifically designed for Whirlpool refrigerators. It provides an accessible storage surface for items in the refrigerator door. The tempered glass shelf is durable and transparent, allowing for easy viewability of the contents stored below.  

Symptoms of a bad shelf glass include cracks, chips, scratches, or other damage that compromises its structural integrity. Over time, frequent opening and closing of the refrigerator door can cause the shelf glass to weaken.

Symptoms of a bad shelf glass include:

• Cracks or breaks from impact or excess weight
• Repeated stresses from door opening wear the glass down  
• Scratches that obstruct clear viewing of items below

This OEM Whirlpool part helps maintain the storage functionality and aesthetics of your refrigerator. It is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This thermostat monitors and regulates oven temperature to help the range reach and maintain the set cooking temperature. Replacing a faulty thermostat restores more consistent baking and roasting results. What it does:

• Senses oven temperature and signals the controller to cycle heating for consistent temperatures.
• Helps prevent the oven from running continuously or failing to reach set temperature.
• Common symptoms that indicate failure: oven won't heat properly, temperature swings, or uneven cooking.
• Direct replacement for the original thermostat used to restore accurate temperature control.

• Disconnect power to the appliance (unplug or shut off circuit breaker) before servicing.
• Access may require removing the oven back panel or control panel.
• Handle the thermostat sensing element gently to avoid damage; route any capillary/sensor tubing carefully.

A replacement hinge pin that secures and guides the appliance door hinge so the door opens, closes and stays aligned. Installs quickly to restore correct door pivot and reduce sag or binding. What it does

• Acts as the pivot point for the door hinge so the door swings smoothly.
• Restores proper door alignment to prevent gaps or doors that won't latch fully.
• Stops noisy or rough door movement caused by a worn or bent pin.
• Helps maintain seal performance by keeping the door flush with the cabinet.

• Disconnect power to the appliance and remove any items from the door area before starting.
• Support the door while removing/installing the pin to avoid damage or injury.
• Use appropriate hand tools and keep track of any retainers or fasteners removed.

Size: 8-18 x 1/2 inch.

Color: White

This thimble provides a finished, secure collar for the dryer's exhaust opening, creating a proper connection point for the vent duct and helping reduce air leaks and lint escape at the wall or cabinet passthrough. What it does:

• Forms the transition between the dryer exhaust outlet and the wall or cabinet duct opening.
• Helps center and support the vent hose or duct so it seals more reliably.
• Reduces gaps that can cause lint accumulation or drafting around the vent opening.
• Common symptoms it can address: visible gap or torn duct at the wall, excessive lint around the vent opening, or poor airflow from a loose connection.

• Disconnect power to the dryer before servicing; for gas dryers, turn off gas supply and follow OEM safety steps.
• Pull the dryer away or remove the cabinet access as needed to reach the vent opening; handle lint carefully and clean the area before installing.
• Slide the thimble into the wall/cabinet opening and align the duct to seat against it; secure per OEM instructions and check for a snug fit and unobstructed airflow.
• Inspect and replace damaged ducting and fasteners; ensure proper clearance and re-check connections after a short test run.

This heater provides controlled warmth to prevent ice buildup and keep your refrigerator operating efficiently. It activates as designed by the control system to clear frost or protect targeted areas so airflow and water flow remain unobstructed. What it does:

• Melts frost from key areas to restore proper airflow and cooling performance
• Helps prevent freeze-ups in components such as evaporators or water lines, depending on model
• Supports consistent temperatures and reliable ice/water dispensing
• Common symptoms of a failed heater: heavy frost on the back panel, reduced cooling or warm fresh-food section, frozen dispenser line, longer run times

• 1 heater

• Disconnect power to the appliance before servicing
• Access the heater's location per your model (often behind an interior rear panel near the evaporator or along a fill/water tube)
• Remove built-up ice, transfer any original clips/brackets, and route wiring exactly as factory
• Avoid damaging coil fins or insulation; restore power and allow a complete cycle to verify normal operation

Color: Universal Silver

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

This mechanical defrost timer advances the refrigerator's defrost cycle so the evaporator periodically melts accumulated frost. It helps restore normal cooling cycles and prevents excessive frost buildup for more reliable refrigerator performance. What it does:

• Advances the appliance between cooling and defrost modes on a timed schedule
• Stops the compressor during defrost so accumulated ice on the evaporator can melt
• Commonly replaced when heavy frost builds on the evaporator or the fridge/freezer cycles abnormally
• Can address symptoms such as excessive frost, reduced cooling, or continuous compressor operation

• Disconnect power to the appliance before starting any repair
• Access the timer through the back or control area per your model's service instructions
• Note wire locations or take a photo before disconnecting to ensure correct reassembly

Made by Whirlpool. This kit includes 15 feet of copper tubing, saddle valve, teflon tape, and tubing connector. Use this kit to connect your refrigerator ice maker to water supply (usually your water shut off valve under the kitchen sink).

Deflector directs airflow inside the appliance to restore consistent temperature distribution and reduce hotspots or frost buildup. Replacing a cracked or missing deflector helps maintain even cooling and reliable performance. What it does:

• Guides internal airflow so cold or warm air reaches the intended compartments.
• Helps prevent uneven temperatures and localized frost or thawing.
• Restores proper circulation when a broken or dislodged deflector disrupts airflow.
• Simple, passive part — when damaged it often causes uneven cooling or increased frost.

• Disconnect power (unplug appliance or switch off breaker) before beginning service.
• Remove shelves, panels, or trim as needed for access; keep fasteners organized.
• Install in the correct orientation; secure without forcing parts or over-tightening.

This hole plug covers an unused opening in the appliance cabinet. It restores a clean, finished look and helps keep spills, dust, and moisture out of internal components.

• Seals an unused hole in the cabinet for a tidy, finished appearance
• Helps protect internal parts from liquids, dust, and humidity
• Covers sharp or unfinished edges around open holes
• Common signs it's needed: missing/broken cap, exposed hole, or a plug that won't stay seated

• Disconnect power and, if applicable, shut off gas/water before starting.
• Remove the old plug; access from the front or from behind the panel as needed.
• Align and press the new plug firmly into the opening until fully seated and flush.
• If panel removal is required for access, handle sheet metal carefully and reinstall all fasteners.

This small metallic flat washer provides a secure bearing surface between fasteners and appliance components to help distribute load and resist loosening. Ideal when replacing worn or missing washers on laundry appliance assemblies. What it does:

• Distributes clamping force from a bolt or nut to prevent damage to softer components
• Helps keep fasteners tight and reduces the chance of loosening from vibration
• Restores proper spacing where a washer has corroded or been lost
• Commonly replaced when you see loose panels, rattles, or misaligned parts near fastener locations

• Verify washer size and thickness match the original before installation
• Use appropriate fastener and torque specifications for your model
• Replace any corroded or damaged fasteners at the same time for best results
• Disconnect power and follow basic safety procedures when working on the appliance