Wrtiiisfaf Parts

This replacement screw secures panels, brackets, and other components in your appliance so they stay tight and properly aligned. Use it to replace missing, stripped, or rusted hardware and eliminate looseness, rattles, or gaps.

• Fastens parts to the cabinet/frame to maintain structural integrity
• Helps keep panels and assemblies aligned to reduce vibration and noise
• Replaces missing, damaged, or corroded screws during service
• Common fix for loose panels or components that no longer hold securely

• Disconnect power and shut off water or gas before servicing
• Match length and thread to the original screw for proper fit
• Hand-start threads to avoid cross-threading; tighten only until snug—do not overtighten
• Tighten them evenly to ensure proper alignment

Screw: 8-16 x 3/8 inch.

FIP door gasket in black. This perimeter seal installs on a refrigerator or freezer door to keep cold air in and humid room air out, restoring proper closure and helping cut down on frost, condensation, and temperature swings.

• Creates a tight seal between the door and cabinet to maintain interior temperatures
• Helps reduce frost/ice buildup and moisture around the door opening
• Supports efficient operation by limiting warm air infiltration
• Common failure symptoms: tears or cracks, warped corners or gaps, brittle rubber, door not closing or staying shut, condensation around the gasket

• Unplug the appliance and clear items from the door being serviced
• Warm the new gasket in hot tap water or with a hair dryer on low to relax packaging bends; do not overheat
• Start the corners, then press the gasket fully into the channel/under retainers along each side
• Allow the gasket to settle/form over the next day

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

This cabinet roller helps a door or pull-out drawer roll smoothly along its track for consistent, quieter operation. It replaces a worn or damaged roller to restore even movement and reduce scraping or sticking. What it does:

• Supports and guides a door or drawer along its track for proper alignment and motion
• Reduces noise and friction from worn or damaged rollers
• Helps eliminate sticking, scraping, or uneven travel during opening/closing
• Restores consistent operation when the original roller is cracked, broken, or missing

• One cabinet roller

• Disconnect power to the appliance before beginning any repair
• Inspect the track and surrounding components for wear or debris; clean as needed
• Many rollers snap or screw into place; use appropriate tools and avoid forcing parts

The air diffuser is an OEM part for Whirlpool refrigerators. This air diffuser is responsible for evenly distributing cool air throughout the refrigerator compartment. 

Causes of a bad air diffuser can include cracks or breaks in the plastic that disrupt proper airflow. Over many years of use, the continuous circulation of air can weaken and damage the diffuser.

Symptoms of a bad air diffuser include:

• Warm or hot spots in the refrigerator compartment 
• Increased energy usage from the cooling system overworking to maintain temperatures
• Collecting of dust or debris inside the refrigerator 

This refrigerator component is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore models. 

Made by Whirlpool. This kit includes 15 feet of copper tubing, saddle valve, teflon tape, and tubing connector. Use this kit to connect your refrigerator ice maker to water supply (usually your water shut off valve under the kitchen sink).

The Diffuser is an OEM part for Whirlpool refrigerators. Located inside the refrigerator compartment, it helps distribute cool air evenly throughout. With perforated passageways, the diffuser facilitates balanced airflow from the evaporator and ensures proper temperature regulation in all refrigerator shelves and bins.

Causes of a bad diffuser can include cracks or breaks from repeated impact or heavy loads, or blockages caused by accumulated dirt and debris over time. 

Symptoms include: 

• Hot or cold spots within the refrigerator 
• Food spoilage from temperature fluctuations
• Condensation or frosting on internal surfaces
• Reduced cooling efficiency 

This OEM Whirlpool replacement diffuser restores optimized interior air circulation. It is compatible with models by Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, and select Kenmore designs.

The door stop shim positions the stop flush and fine-tunes the door's opening limit. Replacing a worn or missing shim helps restore smooth door operation and protects nearby surfaces from over-travel or rubbing.

• Provides correct spacing behind the door stop for proper alignment
• Helps limit the door swing to the intended stop position
• Can reduce wobble, play, or clicking at the stop point
• Replaces cracked, deformed, or missing shim components

• Disconnect power and support the door as needed to prevent strain
• Remove the door stop fastener(s) and note the original shim orientation
• Place the new shim behind the stop; reinstall hardware and tighten without overtightening
• Open and close the door to confirm stop angle and clearances

This refrigerator compressor start device provides the initial boost the compressor needs to start, then disengages. Replacing a failed start device helps restore reliable compressor startup and steady cooling performance.

• Supplies momentary power to the compressor's start winding to get the motor running
• Disengages after startup so the compressor can run normally
• Typical failure symptoms: refrigerator warm or not cooling, compressor won't start, rapid clicking from the compressor area, or intermittent cooling
• Located on the side of the compressor at the back of the appliance

• Unplug the refrigerator and allow the compressor area to cool before servicing
• Access the compressor at the rear; note wire positions and the device orientation
• Pull the old device straight off the compressor pins; seat the new device fully and reconnect wires securely
• If your model uses a separate run capacitor, transfer and reconnect it exactly as originally configured

This air duct is the molded channel that directs airflow within the appliance cabinet. Replacing a cracked or warped duct restores proper circulation so the system can maintain designed temperatures and performance across compartments.

• Routes air between sections to support consistent temperature control
• Helps prevent air leaks and bypass that reduce airflow
• Common signs of failure: broken tabs, cracks, warped plastic, or a loose fit
• Symptoms can include weak airflow at vents, temperature fluctuations, or moisture/frost near openings

• Disconnect power and, if applicable, shut off water before servicing
• Remove any panels/shelves to access the duct; retain fasteners and note seal orientation
• Transfer any reusable foam seals or clips from the original part, seat the duct fully, and secure without overtightening

This small rubber grommet cushions and supports a fan motor, helping reduce vibration and noise while the appliance is running. It fits into the motor bracket to provide a snug, insulated mounting point.

• Isolates fan motor vibration to cut rattling or buzzing
• Helps keep the motor aligned in its bracket
• Can wear, crack, or compress over time, causing vibration or noise
• Replacing a deteriorated grommet restores smooth, quieter operation

• Disconnect power before servicing
• Access the fan assembly and support the motor to relieve strain
• Note grommet orientation; transfer any sleeves or hardware as found
• Seat the new grommet fully in the bracket before remounting the motor

Color: White

This cabinet roller replaces a worn or damaged roller to restore smooth, stable movement for drawers or cabinet doors. It reduces sticking, squeaking, and uneven travel so the cabinet operates quietly and reliably. What it does:

• Supports and guides a cabinet drawer or door along its track
• Restores smooth rolling action when rollers are cracked, missing, or worn
• Stops rubbing, scraping, or loud squeaks caused by damaged rollers
• Helps prevent uneven or stuck drawer/door movement

• Disconnect power (or remove items) and access the roller area before starting
• Inspect the mounting bracket and track for damage; replace any broken clips or guides
• Remove the old roller and press or screw the new roller into the same mounting location

This shim is a thin flat spacer used to align or space appliance components for proper fit and stable operation. It restores correct spacing to reduce rubbing, vibration, or misalignment during repairs and maintenance. What it does:

• Provides a precise gap or alignment between panels, housings, or assemblies
• Helps stop rubbing or scraping noises caused by misaligned parts
• Reduces vibration by stabilizing mating surfaces
• Used when replacing worn or missing shims during panel, bracket, or trim repairs

• Disconnect power (and gas, if applicable) before starting any repair
• Position shim between mating surfaces, then secure fasteners snugly—do not over-tighten
• Inspect surrounding parts and fasteners; replace any that are damaged