Wta3500uc 81/11 Parts

This door gasket is the flexible rubber seal that fits the dishwasher door to keep water inside the tub during cycles. Replacing a worn gasket restores a watertight seal and helps stop leaks and moisture buildup. What it does:

• Seals the gap between the door and tub to prevent water leaks during wash cycles
• Keeps spray and suds inside the dishwasher, protecting surrounding flooring and cabinetry
• Helps reduce odors and mold growth by maintaining a tight seal that limits moisture escape
• Common symptom: water pooling or dripping from the bottom/side of the door
• Common symptom: visible cracks, tears, flattening, or hardened areas in the gasket

• One door gasket

• Inspect the door channel and mating surfaces; clean away residue before installing the new gasket
• Press the gasket evenly into the door channel, working from one end to the other to avoid twisting
• Turn off power and water to the appliance before working on the door; refer to the service manual for model-specific instructions

This bearing set replaces worn drum bearings to restore smooth, quiet rotation and help prevent further damage to the tub assembly. Fits select Bosch WTA/WTL laundry machines. What it does

• Supports the drum/tub shaft so the drum turns smoothly and quietly.
• Worn bearings can cause loud squealing, grinding, or metal-on-metal noise.
• Excessive vibration or a wobbling drum during spin are common signs of bearing failure.
• Replacing the bearing set helps prevent additional wear to the drum and shaft.

• Disconnect power and water before beginning any repair.
• Access requires drum/tub disassembly; keep track of fasteners and seals.
• Bearings are typically press-fit; removal and installation may require a bearing puller/press or specialized tools.

This thermostat with attached sensing cable detects and regulates appliance temperature to help maintain proper heating cycles and protect against overheating. It replaces a failed temperature control component so your appliance can heat correctly and safely. What it does:

• Senses internal temperature and sends a signal to the control to start or stop heating
• Helps prevent overheating by providing accurate temperature feedback
• Works as the temperature-sensing element used by the appliance control board

• Disconnect power before servicing to avoid electric shock
• Handle the sensing cable and probe gently; do not kink or pinch the capillary/sensor
• Verify proper routing and secure mounting of the sensor per the appliance's service instructions

A sealing kit designed to replace worn seals in the dishwasher pump area to stop leaks and restore a watertight pump assembly. Ideal when seals fail and allow water to escape around the pump. What it does:

• Replaces worn or damaged pump seals to help stop leaks beneath the machine
• Restores the pump assembly's watertight seal for proper water circulation and drainage
• Helps prevent water damage to the cabinet and flooring caused by seal failure
• Commonly used when you find water under the dishwasher, visible leaks near the pump, or damp cabinet flooring

• One sealing kit

• Disconnect power and shut off the water supply before starting any repair
• Access usually requires removing the lower access panel and may require partial pump disassembly
• Keep track of small seals and O-rings during removal; inspect related parts for wear

This replacement cable restores a reliable electrical connection between appliance controls and components to help eliminate intermittent operation or loss of function. It's a direct-fit part used where the original wiring is damaged or worn. What it does:

• Carries power or control signals between internal components to enable proper operation
• Replaces frayed, damaged, or broken wiring that can cause intermittent faults or component failure
• Helps restore functionality such as control responsiveness, motor/start signals, or sensor communication
• Prevents arcing or shorting that can occur with compromised insulation or connectors

• Disconnect the appliance from power before inspecting or replacing the cable
• Verify connector orientation and routing to avoid interference with moving parts
• Use only proper connectors; do not use temporary splices that can loosen or overheat

This door latch mechanism secures the appliance door and completes the door-switch circuit so the unit can operate. It replaces a worn or damaged latch to restore proper door closure and reliable operation. What it does:

• Engages and holds the door closed during cycles so the appliance can run.
• Activates the door switch/contact that signals the control board the door is closed.
• Commonly used when the door won't stay closed, the appliance won't start, or the latch feels loose or broken.
• Fits into the door frame and mates with the striker/handle to keep the seal tight.

• One door latch mechanism

• Disconnect power (unplug or switch off breaker) before servicing to avoid electrical shock.
• Access usually requires opening the door panel or removing the inner door; keep track of screws and clips.
• Handle carefully to avoid damaging the latch tabs or wiring; test door operation before reassembling fully.
• If wiring or mounting points are damaged, replace those parts as needed rather than forcing the latch.

This genuine OEM replacement part is a pulley assembly for dryers. Sometimes called an idler arm, the pulley assembly keeps the dryer drive belt under tension as the belt wraps around the dryer drum. If the dryer is no longer spinning properly and is making a lot of noise, the pulley assembly may need to be replaced. Luckily this repair is a relatively simple process.To remove the old dryer pulley assembly, start by making sure the dryer is unplugged. Remove the lint screen from the top of the dryer. Remove the two Phillips screws by the lint screen opening. Depress the clips that hold the top cover down. Lift the top cover and keep it in an upright position. Disconnect the wire harness to the switch that separates the connector. Remove the screws on the front panel. Lift the panel forward and set it to the side. Next, lift the drum and locate the pulley assembly under the drum. Lift the belt off the motor pulley to remove the assembly. Set the new pulley assembly in the same position as the old one and make sure everything is aligned. Rotate the drum to make sure it rotates smoothly. reinstall the panels.This replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador dryers.