Wta3510us Parts

A sealing kit designed to replace worn seals in the dishwasher pump area to stop leaks and restore a watertight pump assembly. Ideal when seals fail and allow water to escape around the pump. What it does:

• Replaces worn or damaged pump seals to help stop leaks beneath the machine
• Restores the pump assembly's watertight seal for proper water circulation and drainage
• Helps prevent water damage to the cabinet and flooring caused by seal failure
• Commonly used when you find water under the dishwasher, visible leaks near the pump, or damp cabinet flooring

• One sealing kit

• Disconnect power and shut off the water supply before starting any repair
• Access usually requires removing the lower access panel and may require partial pump disassembly
• Keep track of small seals and O-rings during removal; inspect related parts for wear

This door latch mechanism secures the appliance door and completes the door-switch circuit so the unit can operate. It replaces a worn or damaged latch to restore proper door closure and reliable operation. What it does:

• Engages and holds the door closed during cycles so the appliance can run.
• Activates the door switch/contact that signals the control board the door is closed.
• Commonly used when the door won't stay closed, the appliance won't start, or the latch feels loose or broken.
• Fits into the door frame and mates with the striker/handle to keep the seal tight.

• One door latch mechanism

• Disconnect power (unplug or switch off breaker) before servicing to avoid electrical shock.
• Access usually requires opening the door panel or removing the inner door; keep track of screws and clips.
• Handle carefully to avoid damaging the latch tabs or wiring; test door operation before reassembling fully.
• If wiring or mounting points are damaged, replace those parts as needed rather than forcing the latch.

This replacement cable restores a reliable electrical connection between appliance controls and components to help eliminate intermittent operation or loss of function. It's a direct-fit part used where the original wiring is damaged or worn. What it does:

• Carries power or control signals between internal components to enable proper operation
• Replaces frayed, damaged, or broken wiring that can cause intermittent faults or component failure
• Helps restore functionality such as control responsiveness, motor/start signals, or sensor communication
• Prevents arcing or shorting that can occur with compromised insulation or connectors

• Disconnect the appliance from power before inspecting or replacing the cable
• Verify connector orientation and routing to avoid interference with moving parts
• Use only proper connectors; do not use temporary splices that can loosen or overheat

A small metal clip that secures the dryer to the top of the washer when stacking, keeping the pair stable during operation. Use this replacement clip if the original is bent, missing, or fails to hold the units together. What it does:

• Locks the dryer cabinet to the washer top to help prevent shifting or sliding during use
• Restores the mechanical fastening point used in factory stacking setups
• Common symptom: dryer feels loose or moves when the pair operate together
• Common symptom: visible bent, cracked, or missing clip at the stack connection

• Turn off and unplug both appliances before attempting installation
• Lift and support the dryer securely during alignment; use a second person or proper lifting equipment
• Slide or snap clip into the factory stacking locations per the appliance's service instructions

This genuine OEM replacement part is a pulley assembly for dryers. Sometimes called an idler arm, the pulley assembly keeps the dryer drive belt under tension as the belt wraps around the dryer drum. If the dryer is no longer spinning properly and is making a lot of noise, the pulley assembly may need to be replaced. Luckily this repair is a relatively simple process.To remove the old dryer pulley assembly, start by making sure the dryer is unplugged. Remove the lint screen from the top of the dryer. Remove the two Phillips screws by the lint screen opening. Depress the clips that hold the top cover down. Lift the top cover and keep it in an upright position. Disconnect the wire harness to the switch that separates the connector. Remove the screws on the front panel. Lift the panel forward and set it to the side. Next, lift the drum and locate the pulley assembly under the drum. Lift the belt off the motor pulley to remove the assembly. Set the new pulley assembly in the same position as the old one and make sure everything is aligned. Rotate the drum to make sure it rotates smoothly. reinstall the panels.This replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador dryers.