Wtvc5330us/11 Parts

This door switch is the electrical interlock that senses the door position and allows the appliance to run only when the door is closed. It restores normal door sensing to prevent unexpected operation and enable cycles to start. What it does

• Detects whether the door is closed and completes the circuit so the appliance can start or continue a cycle.
• Prevents operation when the door is open, improving safety and preventing leaks or heat loss.
• Common symptom: appliance will not start, stops mid-cycle, or shows door-related fault codes when the switch fails.
• Replaces a worn or unreliable door sensing component that causes intermittent starts or shutdowns.

• One door switch

• Disconnect power (unplug or shut off circuit breaker) before attempting replacement to avoid shock.
• Handle connectors and wiring gently; verify connector orientation before reassembly.
• Reassemble panels and test door operation and a short cycle to confirm correct function.

This hose inlet is the water connection hose that routes incoming water to the appliance's inlet valve, restoring proper water feed for cycles. It's a direct-fit replacement designed to match the original part's fit and function. What it does:

• Connects the home water supply to the appliance's inlet valve so water can enter for wash/fill cycles
• Restores proper water flow when the original hose is cracked, split, or leaking
• Helps prevent leaks at the machine entry point when the hose and clamps are properly installed
• Works as the factory-style replacement to maintain correct routing and seal

• One hose inlet

• Turn off power and shut off the water supply before attempting replacement
• Drain residual water from the supply line and appliance to minimize spills
• Inspect and replace any worn clamps or seals; hand-tighten then secure clamps per manufacturer guidance

This sealing strip replaces a worn or damaged door edge seal to help maintain a tight closure and reduce leaks, drafts, and odors. It restores proper sealing where the door meets the cabinet or frame. What it does:

• Provides a consistent seal along the door edge to help prevent water or air leaks
• Helps limit odors and moisture transfer from the appliance compartment
• Reduces rattling or wind noise caused by a compromised door seal
• Restores smooth door closure and alignment where the strip seats

• Disconnect power and water supply before starting work
• Remove the old strip carefully to avoid damaging the door or frame
• Align the new strip with the door edge and press into the channel or mounting surface per OEM guidance
• Trim excess only if specified by the manufacturer; check for a secure, continuous seal after installation

This flat washer secures fasteners and helps distribute clamping force to protect parts from pull-through and wear. It's a small but critical hardware piece that helps maintain proper alignment and reduce vibration in the appliance. What it does:

• Sits under a nut or bolt to evenly spread load and prevent surface damage
• Helps keep fasteners tightened and reduces loosening from vibration
• Protects mating surfaces from wear and deformation
• Can reduce rattling or vibration-related noise when used as intended

• Disconnect power and water before accessing internal components
• Replace like-for-like; do not force or modify the washer to fit
• If other hardware is corroded or damaged, replace affected fasteners as a set

This chrome outer door ring replaces a scratched, dented or missing trim piece to restore the washer door's finished appearance and keep the door edge protected. It's a direct-replacement exterior trim ring. What it does

• Replaces damaged or bent chrome trim around the front-load washer door.
• Restores cosmetic finish and conceals the door edge.
• Helps maintain a uniform seal surface by keeping the door edge supported.
• Useful when trim is cracked, loose, or missing and detracts from operation or appearance.

• Disconnect power before beginning any door disassembly.
• Remove the outer door panel or bezel per OEM instructions to access the trim; handle door glass and bezel carefully to avoid breakage.
• Typical installation requires basic hand tools (screwdriver/torx) and alignment of the trim to the door bezel.

This inner door frame is the metal/plastic support that mounts behind the outer door panel to hold the inner liner, latch, and components in place. Replacing a damaged frame restores proper door alignment and sealing. What it does:

• Provides structural support for the dishwasher door assembly and mounting points for the inner liner and hardware
• Helps maintain proper door alignment so the latch closes securely
• Prevents gaps that can cause water to spray toward the control area or hinge
• Reduces door rattles and vibration from a loose or bent inner frame

• One door inner frame

• Disconnect power and water supply before beginning work
• Remove exterior door panel and any attached trim to access the inner frame; keep track of fasteners
• Handle edges and clips carefully to avoid cutting yourself or damaging the door finish