Wtw57avs-W1 Parts

This touch-up paint kit restores the appliance's painted finish after minor chips, scratches and scuffs to improve appearance and help blend repaired areas with the surrounding surface. Easy spot repair for small cosmetic damage. What it does:

• Conceals small chips, nicks and surface scratches to improve cosmetic appearance
• Blends with the appliance finish for a less noticeable repair
• Helps protect exposed substrate from moisture after paint is applied
• Intended for small spot repairs — not for full-panel refinishing

• Clean and dry the repair area thoroughly before applying paint
• Lightly sand any loose paint or rough edges for best adhesion; wipe clean of dust
• Apply sparingly and allow adequate drying time between coats; follow product label directions
• Use in a well-ventilated area and keep away from children and pets

This tie wire secures wiring and small components to a tree-style mounting post, helping keep harnesses organized and preventing chafing or loose connections. Durable metal construction holds wiring in place for reliable operation. What it does:

• Secures wiring bundles and small components to a tree-style mount or post
• Helps prevent wires from rubbing against sharp edges or vibrating loose
• Reduces risk of intermittent electrical connections caused by loose harnesses
• Keeps internal wiring organized for safer, cleaner repairs

• Tie wire

• Disconnect power and unplug the appliance before servicing
• Position wires on the tree mount and wrap or fasten the tie wire
• Trim or bend any sharp ends to avoid contact with other parts or wiring
• Replace if damaged, corroded, or no longer holds wiring securely

This agitate gear washer is a small flat washer used with the washer's agitate gear to ensure proper spacing and smooth engagement. It helps maintain correct gear alignment so the agitator can move laundry effectively. What it does:

• Provides a stable spacer between the agitate gear and mating components to prevent excess play
• Helps maintain correct gear alignment for consistent agitator movement
• Reduces metal-on-metal contact that can cause noise or premature wear
• Commonly replaced when the agitator feels loose, makes grinding noise, or causes uneven agitation

• High-level replacement: remove agitator/gear per service manual to access washer; reinstall in original orientation
• Use manufacturer torque/settings for reassembly; do not overtighten
• Inspect adjacent gear and splines for wear; replace any damaged components
• Disconnect power and follow safety procedures before servicing the washer

This touch-up paint restores small chips and scratches on painted appliance surfaces to improve appearance and slow corrosion. It's a simple cosmetic repair that helps appliances look cared-for between major services. What it does:

• Covers minor paint chips, nicks and surface scratches
• Helps restore a uniform finish on exterior panels and trim
• Reduces likelihood of surface rust where bare metal is exposed
• Ideal for spot repairs on visible areas without repainting large panels

• One touch-up paint item for appliance finish

• Work in a well-ventilated area and protect surrounding surfaces
• Shake well and test on an inconspicuous spot before applying
• Apply sparingly in thin coats; allow each coat to dry per product instructions
• Keep out of reach of children and away from open flame

This wire shield is a molded protective cover that helps keep wiring routed and protected from heat, abrasion and moving parts. It prevents chafing and reduces the risk of shorts for a safer appliance operation. What it does:

• Covers and routes wiring to protect insulation from heat and friction
• Prevents wires from contacting sharp edges or moving components
• Helps stop intermittent shorts, arcing, or wiring damage that can cause odor or failures
• Maintains proper wire position to support consistent electrical connections

• One wire shield

• Disconnect power to the appliance before beginning any work
• Secure with existing clips or fasteners; do not force or modify the part
• If wiring insulation is melted or damaged, replace wiring/harness before reassembly

This wire harness routes power and signals to lower VMW components, restoring proper electrical connection and reliable operation for affected circuits. It replaces a damaged or worn lower harness assembly to help eliminate intermittent power or control issues. What it does:

• Carries electrical power and control signals between lower VMW components and the main wiring system
• Re-establishes secure plug-and-play connections when wires are frayed, broken, or connectors are loose
• Addresses symptoms such as intermittent operation, no power to lower components, or control malfunctions
• Prevents shorts and poor contacts caused by damaged insulation or broken terminals

• Disconnect power before starting any repair to avoid shock or injury
• Handle connectors by the housings; do not pull on wires when removing or installing
• Route and secure the harness following the appliance wiring path and any retaining clips to prevent chafing
• Verify all connectors are fully seated and inspect for pin damage before reapplying power

This hinge secures and guides a refrigerator door on its pivot, helping the door open and close smoothly while maintaining proper alignment and seal. It's a direct-fit replacement when the original hinge is worn or damaged. What it does:

• Replaces a worn or broken door pivot to restore proper door movement and alignment
• Prevents sagging or binding that can stop the door from closing fully
• Helps maintain an effective door seal to protect cooling performance
• Works as the mechanical mounting point between the door and cabinet

• Basic hand tools are typically required; support the door while removing and installing the hinge
• Follow manufacturer guidance for torque and alignment; adjust door leveling as needed after installation
• Disconnect power and remove contents from the door if required for safe handling

This door hinge replaces a worn or damaged refrigerator door pivot to restore smooth opening and secure door alignment. It provides a stable mounting point so doors open and close without sagging or binding. What it does:

• Supports the refrigerator door and keeps it aligned on the cabinet
• Enables smooth pivoting action for opening and closing the door
• Commonly used to fix door sag, sticking, rubbing, or uneven gaps
• Works with original mounting hardware locations to maintain correct seal

• Unplug the appliance or disconnect power before starting work
• Remove food and secure the door; have a helper support the door during removal/installation
• Use basic hand tools; avoid over-tightening fasteners to prevent damage
• Check door alignment after installation and adjust as needed for a proper seal

This cabinet is the main outer housing that supports and protects the appliance's internal components while giving the unit its finished exterior. It restores structural integrity and proper panel alignment for safe, reliable operation. What it does:

• Provides the structural frame and mounting surface for controls, panels, and internal components
• Protects internal parts from dust, moisture, and incidental contact
• Helps maintain proper airflow and component positioning to reduce vibration and noise
• Restores correct panel alignment and closure when the original cabinet is dented, cracked, or corroded

• One cabinet

• Disconnect power (and gas, if applicable) before beginning any repair
• Installing may require removing trim, controls, and internal components; keep fasteners organized
• Use proper lifting technique and a second person for heavy or bulky cabinets to avoid damage or injury

This factory screw fastens appliance components securely. Replacing a missing, stripped, or rusty screw helps stop rattles, keep panels and brackets aligned, and restore a solid, as-designed fit.

• Secures panels, brackets, and trim to the appliance cabinet or frame
• Helps maintain alignment and reduce vibration or rattling noises
• Replaces damaged, corroded, or missing hardware
• Can resolve loose or shifting components

• Disconnect power and shut off gas/water to the appliance before service.
• Use the correct driver; start threads by hand to avoid cross-threading and do not overtighten.
• Install in the original location and match the OEM fastener type specified in your model's parts diagram.

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.