Wtw804odwo Parts

This wire harness is an OEM-style electrical connector assembly that routes power and signals between components, restoring reliable electrical connections and appliance operation after a damaged or worn harness. What it does:

• Connects controls, switches, and motors to the appliance power and control circuits
• Restores lost or intermittent power/signal paths caused by frayed, broken, or burned wires
• Prevents shorting or open circuits from damaged wiring or loose terminals
• Maintains correct routing and connector fit for safe operation

• Disconnect power (unplug or turn off breaker) before beginning any repair
• Follow the appliance service manual for routing and connector locations to avoid pinching or heat exposure
• Inspect mating connectors and terminals for damage; replace if corroded or burned
• Use basic hand tools

This brace is a replacement mounting bracket that helps secure internal components and cabinet panels so moving parts stay aligned and your appliance operates more quietly and reliably. Simple, direct fit for service repairs. What it does

• Stabilizes and holds panels or assemblies in place to reduce vibration and movement
• Restores proper alignment of connected components for smoother operation
• Helps stop rattling or shifting that can cause noise during use
• Used when a bent, broken, or missing bracket is causing loose parts

• One brace

• Disconnect power (and water if applicable) before servicing the appliance.
• Remove the access panel or cabinet section needed to reach the damaged bracket.
• Replace the bracket using the original mounting screws and hardware; tighten securely but avoid overtightening.

This leveling foot threads into the base of your appliance to support and stabilize it. Adjusting the foot helps level the cabinet, reduce wobble and vibration, and keep doors aligned for smooth, reliable operation. Also called a leveling leg. What it does:

• Provides an adjustable contact point to stabilize the unit on the floor
• Helps level the cabinet so doors align and seal properly
• Reduces rocking, rattling, or excessive vibration on uneven surfaces
• Replaces a cracked, stripped, or missing leveling leg

• 1 leveling foot

• Unplug the appliance and turn off water supply if applicable
• Use a helper to carefully move or tilt the unit; support it securely
• Unthread the damaged foot; thread in the new foot by hand, then fine-adjust with a wrench
• Level side-to-side and front-to-back; ensure all feet make firm floor contact

The Sound Shield is an OEM replacement part for Whirlpool washers. It is a sheet metal panel installed behind the tub that helps reduce noise and vibration during spin cycles. With absorptive insulation, the sound shield dampens noise produced internally. 

Symptoms of a damaged sound shield include:

• Excessively loud operation, especially during high-speed spins
• Rattles, clanks, or resonant noises from inside the washer  
• Potentially weakened structure allowing tub movement
• Causes of a damaged sound shield can include tears or dents sustained over many high-speed spin cycles. Constant vibration may cause stress cracks or loose rivets.

 It is also compatible with some  Whirlpool, Maytag, Amana, and Kenmore brands.

The Speaker is an OEM component specifically designed for Whirlpool brand washers. It alerts users with chime tones or voice prompts during cycle operation or any error states. Precise acoustic engineering allows for clear audio reception even amid operating vibrations. 

Symptoms of a bad speaker include: 

• No audio tones or voice prompts were heard  
• Muffled, distorted, or unusually loud sounds
• Speaker making rattling or buzzing noises

Causes can be damage from water damage, defects in the audio circuitry, or aging components. 

This speaker ensures optimal user communication. Without it, you cannot verify cycle progress or troubleshoot issues. Its dependable performance maintains the washer's convenience.

This Whirlpool OEM part fits perfectly while extending the equipment's lifespan. It is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This clamp secures a washer or dryer hose to its connection to prevent leaks and keep the hose firmly in place during operation. It replaces worn or loose clamps that allow water to escape or hoses to detach. What it does:

• Holds a washer/dryer hose to a nipple, collar or fitting to maintain a sealed connection
• Prevents water leaks caused by loose or corroded clamps
• Stops hoses from slipping off during drain or fill cycles
• Restores proper hose retention and reduces risk of water damage

• Disconnect power and turn off the water supply before starting any repair
• Inspect hose and fitting for damage; replace hose if cracked or frayed
• Use appropriate pliers or a screwdriver for the clamp style; avoid overtightening to prevent hose damage
• Verify a leak-free connection after restoring power and water

The Dispenser Housing is an OEM part for Whirlpool washing machines. It serves as the mount for dispensers containing fabric softener and detergent. 

Causes of bad dispenser housing involve cracks emerging over time, and distorted openings meant for smooth draws.

Symptoms include:  

• Dispensers falling out of place or prematurely discharging contents  
• Disrupted metering from housing leaks along its mounting connections   
• Loosened assembly allowing dispensers to tip during agitation 

This OEM Whirlpool part is also compatible with some Maytag, Amana, and Frigidaire washers.

This outer washer tub is the main exterior tub that surrounds the inner wash basket, helping contain water and support the tub assembly for dependable washing performance. It restores the washer's water-sealing and structural support. What it does:

• Houses the inner tub and helps contain wash water to prevent leaks
• Provides structural support for the tub assembly and associated seals/bearings
• Works with the inner basket, seals, and suspension to maintain proper wash action
• Can address symptoms such as visible leaks from the tub area or excessive tub movement/noise

• One outer tub (single piece as shown)

• Refer to your model's service manual for step-by-step removal and reassembly and follow OEM torque and seal replacement guidance
• Replace any worn seals, gaskets, or mounting hardware during installation to ensure a proper water-tight fit
• Disconnect power and water supply before beginning service to avoid shock or flooding
• Inspect those components and replace as needed

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components.  Proper installation is critical for the washer's structural integrity.

Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time. 

Symptoms of a bad screw include:

• Rear panel detaching from frame opening gaps
• Increased noise and vibrations from a compromised seal  
• Stress on other connections from improper mounting points
• Potential leak paths from openings near hoses or tub areas

This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Bracket Dryer is an OEM part compatible with Whirlpool dryers. This bracket provides stability and structure by securing the dryer cabinet to the base frame. It is a necessary component that allows for proper mounting and alignment of the dryer. 

Causes of a bad bracket can include cracking, bending, or warping over time and use. Exposure to excessive heat or impact can damage the bracket and compromise its integrity.  

Symptoms of a bad bracket include:

• Vibrating or noisy dryer 
• Loose cabinet that is not firmly mounted
• Difficulty leveling or aligning the dryer
• Stress on other components like doors or panels

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Color: White