Xdf250pgr1ww Parts

This dishwasher fill funnel guides water flow into the appropriate channel, helping ensure proper distribution during wash cycles. Replacing a warped or damaged funnel can prevent leaks and restore consistent spray performance.

• Directs water into the dishwasher's internal water feed path
• Helps maintain correct water pressure for spray arms
• Common failure signs: leaking at the funnel area, poor spray performance, residue on dishes, or misalignment with the water feed tube
• Physical damage, warping, or a loose fit are typical replacement indicators

• Disconnect power and turn off water supply before servicing
• Access from inside the tub; remove any retaining screws or clips
• Inspect and reuse existing hardware/seals if still in good condition
• After installation, run a short cycle and check for leaks or misalignment

This thermistor assembly is the dishwasher's temperature sensor. It monitors water temperature so the control can heat and time cycles correctly. Replacing a faulty sensor restores accurate temperature feedback and more consistent wash performance.

• Monitors wash-water temperature and reports it to the control
• Helps regulate heater operation and cycle progression
• A failing sensor may cause extended or incomplete cycles
• Can contribute to poor cleaning from low wash temperatures or temperature-related error codes

• Disconnect power at the breaker before servicing
• Access the sensor at the sump/tub area; release the locking tab/clip to remove, and seat the new sensor fully to ensure a proper seal
• Reconnect the wire harness securely and run a test cycle to check for leaks

This replacement AC wire harness routes power between an appliance's main control and its AC components to restore reliable electrical connections and safe operation. Designed as a direct-fit harness for compatible GE appliances. What it does:

• Provides the factory-style wiring path for AC power and signal connections
• Restores lost or intermittent power caused by damaged or frayed wires
• Replaces burned, corroded, or broken connector ends to improve electrical contact
• Helps stop erratic operation caused by open or shorted harness leads

• One replacement AC wire harness

• Disconnect power to the appliance before starting any repair
• Inspect connectors and routing; replace only if the harness matches OEM connector types
• Secure harness away from sharp edges and moving parts to prevent future damage

Replacement fill funnel hose that routes incoming water into the appliance's fill system. Restores proper water flow to the fill inlet and helps stop leaks at the funnel connection when the original hose is cracked or worn. What it does:

• Channels incoming water from the inlet to the appliance fill assembly.
• Replaces cracked, split, or collapsed funnel hoses that can cause leaks.
• Common symptoms it can fix: water leaking at the funnel connection, slow or incomplete fill, water pooling beneath the appliance.
• Simple direct-replacement part—matches the original funnel hose routing and connection points.

• Always disconnect power and shut off the water supply before servicing the appliance.
• Inspect mating fittings, clamps, and seals; replace clamps or seals if corroded or damaged.
• Use basic hand tools to remove and secure hose clamps; avoid twisting or kinking the hose during installation.

The Upper Rack Roller and Stud Assembly is an OEM replacement part for GE dishwashers. Located inside the upper dish rack, this assembly utilizes precision-engineered plastic rollers and support studs to guide rack movement. Reliable rollers and stable rack positioning are key to smooth operation and effective washing. 

Causes of a faulty assembly include worn or cracked rollers, broken or missing support studs, or loss of lubrication after extended use.

Symptoms of a problematic roller and stud assembly include:

• Noisy or grinding sounds were heard from the upper rack area
• Rack that does not glide smoothly or gets stuck during opening/closing  
• Potential damage to rack or componentry from an unsupported rack
• Difficulty loading or positioning dishes securely 

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore models.

This door spring provides hinge tension for a dryer door, helping it stay closed and operate smoothly. It replaces a worn or broken spring to restore proper door alignment and reliable closing action. What it does:

• Applies consistent tension to the dryer door hinge so the door closes securely.
• Helps prevent the door from sagging or hanging open due to a weakened spring.
• Reduces door misalignment that can interfere with dryer operation or sealing.
• Commonly replaced when the door feels loose, won't stay closed, or sags.

• Disconnect power to the appliance before beginning any work.
• Use care when removing/installing spring components—springs are under tension and can snap.
• Keep track of any clips, screws, or hinge parts removed and reinstall in the original order.

The Screw is an OEM part for GE dishwashers. This screw is designed for various applications, including securing and fastening components in your GE appliance.

A bad screw can result in issues such as loose or unstable components, improper functioning, or even potential damage to other parts. Causes of a bad screw can include wear and tear over time, improper installation, or exposure to extreme conditions.

Symptoms of a bad Screw include:

• Components becoming loose or detached
• Parts not securely fastened
• Unusual noises or vibrations during operation
• Visible signs of damage or wear on the screw

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Lower rack roller and stud assembly is an OEM part for GE dishwashers. It supports smooth movement of the lower dish rack in and out of the tub.

Causes of a bad roller and stud assembly can include wear from repeated extension/retraction of the rack. Mineral buildup may also impede smooth operation over time.

Symptoms of a bad roller and stud assembly include:

• Difficulty fully extending or retracting the lower dish rack  
• Noisy squeaking or grinding noises when moving the rack
• Rack that does not glide easily or gets stuck partially out

Replacing the roller and stud assembly with this genuine GE part restores convenient access to dishes on the lower rack. Its quality ball bearings and durable construction enhance usability cycle after cycle.

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore dishwasher models.
 

The Wash Pump Service Kit is an OEM part for GE dishwashers. It works to circulate water within the dishwasher during wash cycles. The kit includes both the wash pump along seal components. 

Causes of a bad wash pump service kit include deterioration of seals and gaskets, debris buildup restricting pump function, or motor failure due to age.

Symptoms include:

• Inadequate or inconsistent water pressure during the wash  
• Drips or leaks from the pump area
• Grinding or humming noises from the pump
• Inability to properly fill or drain water

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Diverter Assembly is an OEM part for GE dishwashers. It is a water flow management component that directs water via internal channels and ports to target specific spray arms and jets during various wash cycles. 

Symptoms of a faulty diverter include:

• Inconsistent or inadequate rinsing  
• Reduced cleaning power on certain sections of dishes
• Odd noises coming from inside the dishwasher 

Causes can be mineral buildup clogging water passages, worn diverter vanes, or cracks in the assembly housing allowing leakage.

Properly replacing with the authentic GE OEM part restores like-performance water distribution. With uniform coverage, all dishes receive thorough cleaning and drying. Compatible with Hotpoint, RCA, and Kenmore models.

The Fine Filter is an OEM part for GE dishwashers. Located at the bottom of the dishwasher tub, the fine filter traps small food particles and debris to prevent clogs in the wash pump and other components. It is a critical filter that helps optimize cleaning performance and protect internal mechanisms.

Symptoms of a bad fine filter include:

• Reduced or inefficient water spraying from the arms  
• Accumulation of debris inside the tub
• Foul odors emitting from the dishwasher
• Drainage or water flow issues 

Over time, particles can accumulate in the fine filter mesh causing it to become clogged. Choosing this genuine GE replacement ensures optimal filtration. It upgrades your dishwasher with a new filter to once again trap particles and keep the wash system running smoothly. This OEM GE part aligns with specifications for Crosley, KitchenAid, and select Kenmore dishwashers as well.
 

The Plastic Coarse Filter is an OEM replacement part for GE dishwashers. It refers to a screen fitted over the wash impeller that traps soil and food debris. Subject to constant exposure to water and detergents, plastic parts can wear down over many cycles. 

Symptoms of a bad coarse filter include:

• Clogged or blocked mesh no longer prevents large particles from entering the wash arm spray jets  
• Cracks along seams or mounting points where water can seep behind
• Brittle or broken crosspieces within the screen compromising structural integrity

Causes of failure relate to the chemical deterioration of plastic combined with physical stresses as debris repeatedly builds up and then dislodges during high-velocity rinse cycles.

This GE replacement part is also compatible with some Hotpoint and RCA models.

The Rack Roller is an OEM component compatible with GE dishwashers. Located on the rack guide rails inside the washer tub, it facilitates smooth gliding of rack shelving in and out for easy loading and unloading. 

Causes of failure can include cracked/warped rollers from years of continual movement, accumulation of debris preventing free motion, or detachment of roller heads compromising installation.

Symptoms include:

• Difficulty fully extending or retracting racks  
• Off-tracking of shelving from left to right rails
• Scratches or damage to dishware from improper rack functioning 

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Sump Overmold and Gasket Service Kit is an OEM part for GE dishwashers. Containing both the sump overmold and new gaskets, this kit replaces critical components in the lower dishwasher tub assembly.  

Causes of a bad sump or gaskets can include deterioration of rubber materials over multiple years of use and high heat. Mineral buildup during the wash cycle may also damage sealing surfaces.

Symptoms of a bad Sump Overmold and Gasket Service Kit include:

• Leaks or water entry in the bottom of the dishwasher 
• Excess moisture inside cabinet panels
• Inefficient or incomplete drying performance 

This genuine GE part is compatible with select Hotpoint, RCA and some Kenmore models as well.

The Clamp is an OEM replacement part for GE dishwashers. It holds and secures critical components such as tubing or hoses securely in place. Clamps play an important supporting role by fastening tubing and preventing kinking, both of which are essential for proper water flow and circulation within the dishwasher.

Causes of a bad clamp can include cracks, corrosion, or fatigue that causes the clamp to fail in its gripping function over time. Hoses or tubes may also wear down a clamp through constant vibration. 

Symptoms of a bad clamp include:

• Leaks from hoses, tubes or connections  
• Reduced water pressure or uneven spray patterns
• Moisture or water damage around connections
• Loose hoses that rub or chafe

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.