Xdf250pgr1ww Parts

The Friction Washer is an OEM component specifically designed for GE dishwashers. This friction washer is a thin circular part that creates resistance through surfaces rubbing together. It is often used beneath a mounting nut to prevent components from loosening during operation.  

Symptoms of a bad friction washer include loose or separating connections where the washer is installed, such as:

• Drain pump mounting fittings that become detached    
• Water connections that leak at the threaded joints
• Door handle mounts that allow play in the mechanism

Causes of failure can be cracks, wear or deformities in the washer that reduce its friction capabilities over time. Vibrations from use may also cause premature wear.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This dishwasher hose clamp secures internal hoses to pumps or fittings, helping prevent leaks and disconnections. Replace a weakened or damaged clamp to restore a tight, reliable seal at the connection.

• Provides clamping pressure to hold a hose on pump, sump, or drain fittings
• Helps stop water leaking at hose joints
• Resolves: loose or disconnected hoses, water under the unit/base, or poor draining from a slipped drain hose
• Replaces worn, rusted, or deformed clamps after service

• Disconnect power and turn off the water supply before servicing
• Pull the dishwasher forward as needed for access; place a towel or pan to catch residual water
• Seat the hose fully, then compress or tighten the clamp per its design; position just behind the hose barb bead
• Run a short cycle and inspect for leaks at the connection

This sump latch secures the filter/cover at the bottom of the dishwasher tub, locking the sump assembly in place to maintain proper water circulation and filtration while helping keep debris out of the wash pump.

• Locks the sump/filter cover securely to the tub opening
• Helps maintain consistent water flow and wash performance
• Helps prevent large debris from reaching the pump and spray system
• Typical signs it's worn or broken: cracked/missing latch, filter cover won't stay locked, leaking around the sump area, reduced cleaning results

• Disconnect power and shut off water supply before servicing
• Remove the lower rack (and spray arm/filter as needed) to access the latch
• Release and remove the damaged latch; seat components and lock the new latch securely
• Reassemble and run a brief test to check operation and for leaks

The Door Hinge Assembly right is an OEM component specifically designed for GE dishwashers. This door hinge assembly is located on the right side of the dishwasher door and is responsible for securely and smoothly mounting the door while enabling its opening and closing motion.  

Causes of a bad Door Hinge Assembly Right include loose or stripped screws, worn out bearings or bushings, or bent or fatigued metal from repeated use. 

Symptoms of a bad door hinge assembly include:

• The door not latching or sealing properly
• Difficulty opening and closing the door  
• Excessive noise or vibration from the door
• Misalignment that causes the door to rub or interfere

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

This pump isolator hanger cushions and secures the washer drain pump to reduce vibration and noise while keeping the pump properly positioned for reliable water flow. Replaces worn or broken hangers to restore stable pump mounting. What it does

• Cushions the drain pump to reduce vibration and rattling during spin and drain cycles
• Keeps the pump aligned to prevent rubbing, misalignment noise, or premature wear
• Helps maintain a secure pump connection to reduce movement that can lead to leaks
• Used when hanger is cracked, torn, missing, or allowing excessive pump movement

• One pump isolator hanger (single piece as shown)

• Disconnect power and turn off water supply before starting any repair
• Drain remaining water from the washer and access the pump per your model's service instructions
• Inspect surrounding mounting tabs and fasteners; replace any damaged hardware

This main conduit is a molded protective channel that routes and shields the appliance's wire harness to help prevent chafing and moisture exposure. It keeps wiring organized for safer, more reliable operation. What it does:

• Protects wiring from abrasion, pinching, and contact with sharp edges
• Keeps harness routed neatly to reduce strain and prevent snagging
• Helps limit exposure to moisture and debris around electrical connections
• Can be replaced when conduit is cracked, split, or missing to restore proper protection

• Disconnect power to the appliance before beginning any work
• Remove access panels as needed to reach the existing harness conduit
• Slide or snap the conduit into place, ensuring the harness is fully seated and not pinched
• Inspect wiring for damage; repair or replace any frayed insulation before reassembly

The Door Hinge Assembly Left is an OEM component specifically designed for GE dishwashers. This door hinge assembly is located on the left side of the dishwasher door and is responsible for securely and smoothly mounting the door while enabling its opening and closing motion.  

Causes of a bad Door Hinge Assembly Left include loose or stripped screws, worn out bearings or bushings, or bent or fatigued metal from repeated use. 

Symptoms of a bad door hinge assembly include:

• The door not latching or sealing properly
• Difficulty opening and closing the door  
• Excessive noise or vibration from the door
• Misalignment that causes the door to rub or interfere

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models. 

The Water Valve Assembly is an OEM replacement part for GE dishwashers. This valve assembly controls the flow of water into the dishwasher during each cycle stage. It regulates water temperature and volume to the desired wash and rinse settings.

Causes of a bad water valve can include mineral buildup interfering with valve function, worn internal seals, or obstruction in the valve inlet or outlet ports.

Symptoms of a bad water valve include:

• Incorrect or inadequate water levels during the cycle
• Inability to reach proper wash or rinse temperatures
• Water not shutting off fully between cycles
• Leaks from the water inlet area

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models