Zgp366nrss Parts

This side support panel replaces a damaged or missing support on the appliance's side, helping secure and align the cabinet and trim so the unit sits solidly and looks finished after installation or service. What it does:

• Provides structural support for the side of the appliance cabinet and adjacent trim
• Helps maintain correct spacing and alignment next to countertops or panels
• Replaces a bent, warped, or corroded panel
• Reduces rattles or rubbing caused by a loose side assembly

• One side support panel

• Disconnect power; turn off gas supply before servicing
• Carefully pull the unit forward for side access; support it to prevent tipping
• Remove fasteners, transfer any clips/brackets from the old panel, and reinstall with existing hardware
• Wear cut-resistant gloves and verify clearances and level before final tightening

High-voltage harness routes power between high-voltage components in a microwave oven, restoring safe electrical connections and preventing intermittent operation or arcing when replacing a damaged or burned wiring assembly. What it does:

• Connects the microwave's high-voltage components to maintain proper power flow.
• Failing or damaged harnesses can cause no-heat, intermittent heating, arcing, burning smell, or blown fuses.
• Replaces frayed, melted, or corroded high-voltage wiring that risks shorting or unsafe operation.
• Designed to restore original electrical routing and secure connector fit for reliable operation.

• Disconnect power and unplug the appliance before servicing. Ensure the high-voltage capacitor is properly discharged—do not attempt service without this step.
• Inspect connectors, insulation, and routing; replace damaged clips or retainers and secure wiring away from sharp edges and moving parts.
• Follow the wiring diagram for correct connections.
• Never operate the appliance with covers or safety panels removed.

The Safety Valve Assembly is an OEM part for GE gas ranges. It automatically cuts off gas flow if excess pressure develops, providing critical safety protection.  

Symptoms of a faulty safety valve include:

• The range does not ignite and burners fail to light
• Gas leaks occur even when burners are off
• Responsiveness issues adjusting burner flames 

 Causes involve worn seals, dirt/debris blocking valve ports, or cracked componentry from shock over time.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This replacement screw fastens appliance components to restore secure fit and reduce vibration or panel movement. Simple, direct replacement for a missing or stripped fastener to help maintain proper assembly and operation. What it does:

• Secures panels, brackets or trim to keep parts aligned and prevent rattling
• Restores mounting where a lost or damaged screw causes loose or sagging components
• Helps maintain electrical and mechanical connections by keeping parts properly seated
• Small hardware solution for cosmetic and functional stability

• Use the correct sized screwdriver or driver bit to avoid stripping the head
• Inspect mating threads and replace if damaged; do not force a stripped screw
• Tighten until snug — avoid over-tightening which can crack plastic or strip threads
• If accessing areas near power or controls, disconnect appliance power first and follow all safety precautions

18K

Size: 8 - 32 inch.

Size: 8-18 x 1/2 inch.

A 45 mm tangential blower that restores directed airflow in heating and cooling cavities to help maintain even temperatures and protect internal components. Fits factory blower mounts and connects to existing wiring harnesses. What it does:

• Moves air along the oven/cabinet cavity to promote even heat distribution and help vent hot spots
• Cools nearby electronics and components to reduce overheating risk
• Replaces worn or noisy blowers to restore proper airflow and reduce unusual motor noise
• Helps maintain designed airflow for venting and exhaust paths

• Disconnect power at the breaker before starting any repair
• Handle with care; blower edges and surrounding sheet metal may be sharp
• Verify blower orientation and wiring match the original before securing
• Basic hand tools typically needed; follow for panel removal and reassembly

Natural gas. Main burner.

This regulator controls gas pressure to the range/oven so burners and the oven heat consistently and safely. Replaces a failed regulator to restore proper flame behavior and reliable cooking performance. What it does:

• Regulates incoming gas pressure to the appliance's burner system
• Helps maintain steady, even flame height for consistent cooking
• Resolves symptoms like weak or uneven flames, burners that won't light, or poor oven heat
• Prevents over-pressurization that can cause unstable burner operation

• One regulator

• Turn off the gas supply and electrical power before beginning work
• Install using proper fittings and thread sealant rated for gas; tighten to OEM torque specs
• After installation, test all gas connections for leaks (do not use an open flame)

The Harness Burner Box is an OEM part for GE gas ranges. It is the bundled wire assembly that connects the control board to the gas valves and igniters. 

Causes of a bad harness burner box include worn insulation on internal wires, broken or shorted connections, and damage from vibration or movement over time.

Symptoms of a bad harness burner box are:

• Failure of individual burners to light or ignite properly
• Unstable flame or incomplete combustion 
• Responsiveness issues when adjusting burner heat levels
• Loose or dangling wires inside the range cavity

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore gas range models. 

The Encoder Assembly is an OEM part for GE gas ranges. It digitally converts analog knob movements into signals to control the gas valve, igniter, and temperature settings. 

Causes of a bad encoder assembly include degradation of internal sensors and switches over time, loose wiring connections, or impacts that cause misalignment.

Symptoms of a bad encoder assembly are:

• Delays or errors when trying to light burners
• Inaccurate flame height and temperature level responses 
• Knobs feel sticky, sluggish or jump between settings
• Error codes indicating control module communication issues

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore gas range models.

This is a stainless-steel machine screw used to secure components in appliances. Its #8-18 thread and 3/8" length provide a reliable, corrosion-resistant fastening where a short machine screw is required. What it does:

• Fastens panels, brackets, or small assemblies with a #8-18 threaded hole
• Resists rust and corrosion in humid appliance compartments
• Provides a short, secure hold where space is limited
• Compatible with standard #2 Phillips or compatible driver bit for installation

• Power off and unplug the appliance before servicing
• Use the correct driver to avoid stripping the head
• Do not overtighten; stop when snug to avoid thread or component damage
• If replacing multiple fasteners, reuse only the same size and type

Size: 8 - 18 ab hxw 5/8 s