Zsc2201jss Parts

This is a binding-head screw used to fasten panels and components on compatible GE appliances. It provides secure, low-profile fastening where a binding head design is required for proper fit and alignment. What it does

• Secures panels, brackets, or small assemblies to prevent movement or rattling.
• Replaces a missing or stripped screw that causes loose parts or squeaks.
• Restores proper alignment for components that rely on the binding-head profile.
• Works where a shallow, rounded head and threaded shaft are specified.

• Use the correct driver size to avoid cam-out or head damage.
• Do not overtighten; snug until secure to avoid stripping threads or damaging parts.
• Disconnect power and follow all appliance-specific safety procedures before accessing panels.

This heater holder is the mounting bracket that secures the oven heating element in place so the element stays aligned for reliable heating and safe operation. It helps prevent movement that can cause uneven cooking or damage. What it does:

• Holds and stabilizes the oven/heater element in the cavity so it stays properly positioned
• Keeps the element from contacting other components, reducing the risk of shorts or damage
• Helps maintain even heat distribution by preventing element sagging or misalignment
• Fits where the element mounts and supports normal operation of the heating circuit

• One heater holder/mounting bracket

• Turn power to the appliance off at the breaker before servicing to avoid shock
• Inspect the element and surrounding insulation for damage when replacing the holder
• Typically secures with screws or clips—retain hardware and note orientation for reassembly

This mounting bracket provides a secure support point for appliance components, restoring proper alignment and stability. Use it to replace a bent, broken, or missing bracket to stop rattling and prevent parts from shifting. What it does:

• Secures panels, assemblies, or internal components in their correct position
• Restores stability to reduce vibration, noise, and misalignment issues
• Replaces damaged or corroded brackets that allow parts to sag or move
• Matches OEM fit and mounting points for reliable reinstallation

• Install with the appliance unplugged or power/gas disconnected for safety
• Keep original fasteners when possible; replace any stripped or damaged screws
• Hand-start fasteners, then tighten to secure without over-torquing

This shaft ring is a small retaining clip that secures a rotating shaft in place, helping keep connected components aligned and moving smoothly. It's a simple replacement that restores proper shaft retention and reduces wobble. What it does:

• Clips into a shaft groove to hold components on the shaft
• Prevents axial movement and keeps parts from sliding out of position
• Helps reduce noisy or unstable operation caused by loose shaft components
• Commonly used where a compact, reliable retention method is required

• One shaft ring

• Inspect the shaft and groove for wear or debris before installing; clean as needed
• Use appropriate snap-ring pliers or a safe, non-marring tool to install/remove the ring
• Ensure the ring fully seats in the shaft groove and the retained part is secure before reassembly
• Disconnect power and follow appliance safety procedures before servicing

This indicator is the replacement panel light that shows oven or range status, restoring visible feedback for bake/broil/timer functions. It fits into the control panel and connects to the appliance's wiring harness. What it does:

• Illuminates the control panel to indicate operating modes or timers
• Replaces a cracked, burned out, or non-lighting indicator
• Helps you see oven status at a glance for safer operation
• Compatible with controls that use a single small panel indicator lamp

• Always disconnect power to the appliance before starting work to avoid shock
• Installation typically requires removing the control panel or console to access the indicator
• Handle the part and wiring gently to avoid damage; ensure secure connector seating

This turntable shaft is the center coupler that links the microwave's turntable motor to the glass tray. Replacing a worn or cracked coupler restores smooth rotation so food heats more evenly without slips, stalls, or scraping.

• Couples the turntable motor to the tray for consistent rotation
• A worn or stripped hub can cause the tray to stop turning or turn intermittently
• Damage can lead to wobbling, slipping, or scraping noises at the center
• Loss of rotation can result in uneven cooking or cold spots

What's included: One turntable shaft Install notes:

• Disconnect power or unplug the microwave before servicing
• Remove the glass tray and roller ring; lift the old coupler straight up from the center
• Align the new coupler with the motor stem/key and press it fully into place
• Reinstall the roller ring and tray; verify smooth rotation with a microwave-safe cup of water