Tube Parts

Note: tube is 1/4" in outside diameter.

Tub to pressure switch hose.

This burner supply tube delivers gas from the range manifold to an individual surface burner, restoring proper fuel flow so burners ignite and produce an even flame. Direct replacement for the corresponding OEM supply line. What it does:

• Channels gas from the manifold to a specific surface burner for normal operation
• Helps restore ignition when a burner won't light or has a weak/uneven flame
• Replaces corroded, cracked or bent tubing that can restrict gas flow
• Designed to match the original routing and connection points for proper fit

• Turn off the appliance gas supply and electrical power before beginning any work.
• Confirm the correct tube orientation and secure fittings to the manifold and burner assembly.
• After installation, check all connections for leaks with a soapy-water solution or approved leak detector; do not use an open flame.

This replacement tube routes water inside the refrigerator to the dispenser or ice maker, restoring proper water flow and preventing leaks when the original tubing is cracked or worn. Simple direct-fit replacement when the OEM tubing fails. What it does:

• Carries water between the refrigerator supply and the dispenser or ice maker
• Replaces cracked, split or collapsed tubing that can cause leaks
• Helps restore steady water flow and proper ice-making or dispensing
• Prevents water damage from deteriorated or pinched lines

• Designed for refrigerator models that use this exact OEM tube
• Disconnect power and shut off the water supply before replacing tubing
• Inspect connections and seals; replace any damaged clips or fittings to ensure a watertight seal

5 foot. Package of 2.

A direct-replacement inlet tube that routes incoming water from the valve to the appliance tub. Restores proper water flow and prevents leaks for reliable fills and cycles. What it does

• Channels water from the fill valve to the appliance tub or wash chamber.
• Replaces cracked, split, or deteriorated tubing that causes leaks.
• Helps resolve no-fill or slow-fill symptoms when the valve and hoses are intact.
• Prevents water pooling and potential water damage from failed tubing.

• Disconnect power and shut off the water supply before starting.
• Inspect and reuse or replace any clamps, seals, or grommets as needed.
• Verify correct orientation and seating to avoid kinks or strain on connections.
• Use basic hand tools; test for leaks after reassembly.

This tube routes water from the refrigerator's water valve to the dispenser or ice system, restoring proper water flow and stopping leaks when a cracked or clogged supply tube is the issue. Easy direct replacement for affected lines. What it does

• Carries water from the valve to the dispenser or ice maker so the appliance can fill and dispense properly.
• Commonly replaced when you see leaks at fittings, a puddle under the fridge, or a visibly cracked or split tube.
• Can restore normal water flow when the line is pinched, kinked, or partially obstructed.
• Works with factory fittings and clamps used on the valve-to-ice maker/dispenser connection.

• Turn off the refrigerator's water supply and unplug the appliance before starting; drain remaining water from the line.
• Inspect fittings for damage; loosen or remove existing clamps/fittings to swap the tube, then secure new tube and clamps to prevent leaks.
• After installation, restore water and power, check all connections for leaks, and run the dispenser/ice maker briefly to confirm proper flow.

This fill and drain hose assembly routes water into and out of the washer, helping the machine fill, drain and operate normally. Replacing a worn or damaged hose prevents leaks and restores reliable water flow. What it does

• Carries incoming water to the washer tub during the fill cycle.
• Provides a path for water to exit during drain/spin cycles.
• Commonly replaced for visible cracks, pinholes, leaks, or kinking that restricts flow.
• Can resolve symptoms like water on the floor, poor filling, or incomplete draining.

• Turn off power and shut off water supply before beginning work.
• Inspect hose routing and fasteners; replace any damaged clamps or connectors.
• Tighten connections securely and test for leaks at low flow before a full cycle.

This drain hose routes and removes wastewater from the appliance so it can pump out normally and avoid standing water. It's a direct-fit service part used to restore proper draining. What it does

• Carries wastewater from the appliance pump to the household drain or air gap
• Restores normal draining when original hose is cracked, split, or leaking
• Helps prevent water backing up into the appliance when properly routed and secured
• Can stop intermittent leaks or reduced drain performance caused by hose damage

• One drain hose

• Disconnect power and turn off water supply before starting any repair
• Inspect hose routing and replace with the same path to avoid kinks or high loops that trap water
• Secure hose connections with appropriate clamps; tighten but avoid over-torquing
• After installation, run a short drain cycle and check all connections for leaks

This flexible replacement hose restores proper fluid flow for the appliance by replacing cracked, clogged, or collapsed tubing. It's a direct-fit service part used where a flexible water or drain line is required. What it does:

• Carries water or discharge fluid between appliance components to enable normal operation
• Replaces damaged, cracked, or collapsed hose sections that can cause leaks
• Helps eliminate slow draining or intermittent flow caused by blockages or pinch points
• Restores a secure connection when fittings or tubing have worn

• Disconnect power and shut off water supply before starting any repair
• Inspect fittings and clamps; reuse only OEM-recommended clamps or replace if corroded
• Route hose without sharp bends or kinks and secure to prevent rubbing or chafing

This inlet hose delivers fresh water from your home supply to the appliance, restoring proper fill and preventing leaks. It's a direct-fit replacement designed to restore normal water flow and stop visible hose damage. What it does:

• Channels water from the household supply into the appliance's inlet valve
• Replaces cracked, split, or leaking inlet hoses that allow water to escape
• Helps resolve symptoms like weak/no fill, visible dripping at the connection, or intermittent water flow
• Matches OEM routing and connection points for a proper seal when installed correctly

• Turn off water supply and unplug the appliance before starting
• Inspect fittings and replace any damaged seals or washers as needed
• Hand-tighten connections and finish with a quarter turn; avoid overtightening to prevent damage
• Run a short test fill and check all connections for leaks before returning the appliance to service

This hose kit replaces worn or damaged appliance hoses to restore proper water flow and prevent leaks. It's a direct-fit replacement for compatible Whirlpool systems and helps stop visible leaks and restore normal fill/drain operation. What it does

• Replaces cracked, split or leaking hoses to stop water loss and reduce risk of appliance damage
• Restores reliable water flow for filling and draining functions
• Helps eliminate poor draining, intermittent filling, or water pooling near the appliance
• Works with existing clamps and connections when installed correctly

• Disconnect power and shut off the water supply before starting any repair
• Inspect connection fittings and replace clamps if worn; ensure a snug, leak-free fit
• Route hoses without kinks and secure to avoid chafing or strain
• After installation, run a short cycle and check all connections for leaks

This replacement water dispenser valve tube routes water from the dispenser valve to the dispenser outlet so your appliance can deliver water and ice correctly. It restores a proper, leak-free flow path for the dispenser. What it does:

• Connects the dispenser valve to the dispenser outlet, directing water flow for dispensing and ice-making functions
• Replaces cracked, pinched, or deteriorated tubing that can cause leaks or weak/blocked water flow
• Helps stop visible leaks under the dispenser area and restore normal dispensing performance
• Compatible with factory valve connections and dispenser fittings when the OEM tube is specified

• One replacement water dispenser valve tube

• Disconnect power and shut off the water supply before starting work
• Inspect matching fittings and clamps; reuse only if undamaged — replace clamps if corroded
• Route the tube following factory routing to avoid kinks and ensure secure connections