Sgm464ems/Lp Parts

This brass nut secures a threaded connection within the burner/manifold area of compatible cooking appliances, helping restore a tight, reliable attachment. Replace a worn or missing nut to keep fittings properly fastened and operating as designed.

• Secures a threaded fitting or tube connection on the burner/manifold assembly
• Helps maintain a tight, reliable joint when installed correctly
• Replaces a stripped, rounded, cracked, or missing nut
• Can address a loose connection that will no longer tighten

• Disconnect power and shut off the gas supply before servicing; allow all surfaces to cool
• Start threads by hand to avoid cross-threading
• Use a backup wrench on the mating fitting to prevent twisting or kinking tubing
• Do not overtighten; after reassembly, perform an approved leak-check before returning to service

This spill gasket seals the gap between the cooktop surface and the underlying spill tray, helping contain liquids and crumbs so they don't seep into the burner box. Replacing a worn gasket protects internal components and supports reliable ignition. What it does:

• Creates a perimeter seal to contain spills on the cooktop surface
• Helps prevent moisture and debris from reaching igniters and wiring
• Reduces seepage into the burner box/spill tray area
• Common signs include visible cracks or flattening, liquids leaking below the top after spills, and prolonged igniter clicking after cleaning or spills

• Spill gasket

• Disconnect power and shut off gas supply before servicing
• Remove grates, burner caps, and top as needed to access the old gasket
• Clean mating surfaces; install the new gasket without stretching and seat evenly with no gaps
• Reassemble and restore utilities; check for leaks per manufacturer guidance

A replacement service burner ring that restores proper burner alignment and appearance on compatible gas cooktops and ranges. Keeps the burner assembly seated correctly for consistent ignition and safe operation. What it does:

• Replaces a cracked, warped, or corroded burner ring to restore correct burner positioning
• Helps maintain proper flame shape and stable ignition at the burner head
• Can reduce visible damage and improve cooktop appearance after wear or impact
• Designed for use with compatible Samsung gas cooktops and ranges

• Turn off the gas supply and let the cooktop fully cool before servicing
• Remove grates and burner caps, then lift out the old ring before installing the replacement
• Inspect burner ports and ignition components for damage or debris while servicing

This large burner cap sits above the gas burner head on your range or cooktop. It shapes the flame and shields the burner from spills, promoting even heating and easier cleanup.

• Sits on the burner head to shape and distribute the flame evenly
• Helps protect the burner from drips, debris, and corrosion
• Replace if chipped, warped, or missing to correct hard-to-light or uneven/yellow flames
• Ensures proper simmering and consistent heat when seated level and centered

• Turn off gas and allow the cooktop to cool completely before servicing
• Clean and dry the burner head and seating surface
• Align and center the cap on locator pins; ensure it sits flat and stable
• Test ignition and flame pattern; reseat if the flame is uneven

This medium burner cap sits on top of the gas burner head to shape an even, stable flame and shield the head from spills and debris. Replacing a damaged or missing cap helps restore consistent ignition and heat distribution.

• Directs and spreads the flame evenly across the burner head for proper cooking performance
• Helps protect burner ports from drips, grease, and debris that can affect flame quality
• Supports reliable ignition when correctly centered and seated
• Common symptoms: uneven or yellow flames, delayed ignition, fluttering flame, or a chipped/warped/missing cap

• Allow the cooktop to cool completely and verify all controls are OFF
• Lift off the old cap; clean and dry the burner head and ports before installing
• Center the new cap on the matching medium burner head so it sits level and flush
• Light the burner to test; if the flame is uneven or yellow, turn off, let cool, and reseat the cap until the flame is steady and blue

This spark module controls the ignition system that creates the sparks to light gas burners, restoring reliable ignition for range and cooktop burners. Replaces a failed module to help get burners lighting again. What it does:

• Generates high-voltage sparks to ignite gas burners when a burner control is turned on
• Stops ignition attempts when the control is turned off or a fault is detected
• Common symptom: burners will not light or there is no spark at burner electrodes
• Also used when you hear clicking without ignition or intermittent ignition on one or more burners

• One spark module

• Disconnect the appliance from power and shut off the gas supply before servicing
• Handle the module and electrode leads carefully to avoid damage to wiring and connectors
• Verify correct connector orientation and secure mounting; replace all damaged wires or fasteners

This burner O-ring seals the D burner assembly on gas cooktops. It helps keep the fuel path airtight and protected from spills, supporting consistent ignition and a stable, properly shaped flame.

• Maintains a seal between burner components to preserve correct gas/air mixture
• Helps prevent leaks and moisture intrusion around the burner well
• Can contribute to resolving weak/uneven flame, flame lifting, or hard-to-ignite burner when the original seal is worn
• Replaces cracked, flattened, swollen, or missing O-rings

• Turn off gas supply and disconnect power. Allow the cooktop to cool completely.
• Remove grates, burner caps, and the burner head to access the O-ring; note the original orientation.
• Clean mating surfaces; install the new O-ring carefully without twisting or pinching.
• Reassemble, restore gas/power, and perform a leak check. Test burner operation.

This burner ring replaces a damaged or worn stovetop burner ring to restore even flame distribution and a secure fit for the burner cap. It's a direct-replacement part designed for compatible Samsung gas cooktops. What it does:

• Provides the ring surface that channels gas flames around the burner cap for proper cooking heat
• Restores stable flame pattern and ignition reliability when cracked, warped, or corroded
• Helps prevent flame blowout and uneven heating caused by damaged rings
• Compatible surface design ensures correct alignment with the burner base and cap

• Turn off gas supply and unplug the appliance before servicing; follow all safety precautions
• Allow the cooktop to cool completely before attempting replacement
• Remove burner cap and existing ring, then set the new ring in place and reassemble in reverse order

This burner control knob replaces a worn or missing knob on your cooktop. It attaches to the burner valve stem so you can set flame levels smoothly and accurately, while restoring the original look with the printed logo. What it does:

• Mounts to the burner valve stem to adjust heat output
• Provides a secure grip and pointer for setting positions
• Common signs it's needed: cracked knob, stripped/split insert, knob falls off or spins freely
• Helps restore consistent burner control and appearance

• One control knob with logo

• Turn all burners off and allow the surface to cool; disconnect power to the appliance before servicing
• Pull the old knob straight off the stem
• Align the flat/keyed sides and push the new knob straight on until fully seated
• Verify smooth rotation and correct pointer alignment with the panel markings

This small burner cap covers the gas burner head on your cooktop to shape and protect the flame. Replacing a worn, cracked, or missing cap restores even heat distribution and reliable ignition for consistent cooking results.

• Sits over the burner head to distribute flame evenly and stabilize heat
• Shields the burner from spills and debris that can affect performance
• Proper seating supports quick, consistent ignition
• Common signs it's needed: uneven or yellow flames, difficulty lighting, or a damaged/missing cap

• Ensure all controls are off and the cooktop is completely cool
• Lift off the old cap; clean and dry the burner head surface
• Place the new cap on the matching small burner, centered and fully seated
• Light the burner to confirm an even, steady flame; reseat if necessary

This burner ring sits on the burner head of a gas cooktop to direct gas evenly around the flame ports. Replacing a warped or clogged ring helps restore even heating and reliable, consistent ignition.

• Channels gas evenly around the burner head for a balanced flame pattern
• Supports proper burner cap alignment and stable simmer performance
• Common symptoms of a failed ring: uneven or yellow flames, sputtering, or delayed ignition
• Can contribute to weak heat output or a burner that won't light reliably

• Shut off gas supply and power; allow the cooktop to cool completely
• Remove grate and burner cap, then lift off the old ring
• Clean carbon and debris from the burner head; do not enlarge or damage the ports
• Align and seat the new ring flat, reinstall the cap and grate, and test for proper flame and ignition

This service regulator controls and stabilizes incoming natural gas pressure to the appliance, helping burners maintain reliable ignition and steady flame strength. It replaces a worn regulator to restore correct gas pressure regulation. What it does:

• Reduces and regulates incoming natural gas pressure to the 3–6 in. water column range for safe, consistent burner operation
• Helps restore proper ignition and steady flame when weak or uneven flames occur
• Prevents over- or under-pressurization that can cause poor heating performance
• Works as the pressure-regulating component in the appliance's gas supply system

• 1 service regulator

• Shut off gas supply and electrical power before beginning work
• After installation, perform a certified gas leak test and verify correct burner operation and pressure per manufacturer specs
• Do not attempt installation if you are not trained or certified to work on gas systems