Vg233-8 Parts

This replacement burner cap covers the cooktop burner to help shape and stabilize the gas flame for efficient cooking. It restores proper flame pattern and protects the burner head from spills and debris. What it does:

• Centers and shapes the gas flame for even heating across cookware
• Protects the burner head from food, grease and corrosion
• Helps prevent flame irregularities and poor ignition caused by a damaged or misplaced cap
• Compatible with the matching burner head and cap seating on the cooktop

• Turn off all power and gas to the appliance and allow the cooktop to cool before servicing
• Remove grates and lift off the old cap; set the new cap down so it sits flat and centered on the burner base
• Inspect the burner head for clogs or damage and clean gently if needed before installing the cap
• If you smell gas or the burner behaves unusually after installation, stop use.

This burner head replaces the VG 230/330 style gas burner on compatible cooktops, restoring even flame distribution for reliable cooking. It's a direct-fit component used where the original burner cap is damaged or worn. What it does:

• Directs and shapes the gas flame for even heating across cookware.
• Replaces cracked, warped, or clogged burner heads that cause irregular flames.
• Helps restore proper ignition and consistent burner performance.
• Suitable for burners that show yellow tipping, sputtering, or weak flames (symptom dependent on overall valve and ignition condition).

• One burner head (VG 230/330 style)

• Turn off gas supply and power to the appliance before beginning service.
• Remove grates and burner caps; lift out the old burner head and seat the replacement securely on the base.
• Ensure burner ports are clean and unobstructed; test for proper ignition and flame pattern after reassembly.

Replacement burner cap that sits on the gas burner head to protect components and shape the flame for even cooking. Restores proper flame pattern and stovetop performance when the original cap is cracked, warped, or missing. What it does:

• Covers and protects the burner head from spills and debris.
• Helps shape and stabilize the burner flame for consistent heat.
• Promotes reliable ignition by providing the correct flame path.
• Commonly replaces caps that are cracked, warped, or causing uneven flames.

• Turn off the cooktop and gas supply and ensure all parts are completely cool before handling.
• Remove the old cap, clean the burner head of debris, then seat the new cap flat and centered on the burner head.
• No special tools typically required; verify correct fit before using the burner.

This is a replacement M5 x 20 gasket designed to restore a secure seal where the original small rubber gasket has failed. It prevents leaks and maintains proper pressure or fluid routing in the assembly. What it does:

• Provides a tight seal at the specified M5 x 20 connection to stop drips and seepage
• Restores proper seating for valves, fittings, or small housings that use this gasket
• Helps prevent airflow or fluid loss that can cause poor appliance performance
• Addresses common symptoms such as minor leaks, moisture buildup, or loose-fitting parts

• Replace with the appliance powered off and water/gas disconnected where applicable
• Inspect mating surfaces for damage or debris and clean before installing the new gasket
• Lubricate lightly with approved lubricant only if specified by the manufacturer

This thermocouple monitors the burner flame and works with the safety valve. It allows gas flow only while a flame is present and lets the valve close when no flame is detected, helping restore dependable burner operation.

• Senses burner flame heat and sends a small millivolt signal to the safety valve
• Works with the flame-failure safety system to maintain or cut gas flow based on flame presence
• Common symptoms can include: burner lights but goes out when the knob is released; needing to hold the knob down unusually long to keep the burner lit

• Disconnect power and shut off gas before servicing
• Allow the unit to cool; remove grates/caps to access the sensor tip and route the lead to the valve connection as originally installed
• Do not kink or sharply bend the lead; position the tip within the burner's flame envelope
• After reassembly, restore gas/power and test burner operation

This small rubber gasket seals and cushions an M4 fastener to help prevent leaks and reduce vibration at attachment points. It's a compact replacement part used where a watertight or vibration-damping seal is needed. What it does:

• Creates a seal around an M4 screw or bolt to help prevent water intrusion
• Cushions fasteners to reduce vibration, noise, and metal-on-metal wear
• Restores a tightened fastener's proper sealing surface when the original gasket is worn
• Helps maintain appliance integrity around panels, brackets, or connections

• Power off and unplug the appliance before starting any repair.
• Confirm the gasket's size matches the fastener and seating area before installation.
• Install flat against the mating surface; tighten fastener snugly but avoid over-torquing which can deform the gasket.
• Handle small parts carefully and retain any removed hardware for reassembly.

This burner lid is the replacement top cover for a VG 230/330 gas burner assembly, restoring proper burner protection and heat distribution for reliable cooktop operation. Designed to fit the OEM burner geometry and surface finish. What it does:

• Covers and protects the burner cap and inner components from spills and debris.
• Helps channel flame and heat for more even cooking performance.
• Reduces the chance of food or liquids reaching ignition parts that can cause burner issues.
• Common symptom: cracked, warped, or missing lids that allow uneven flames or visible damage.

• Turn off gas and power to the appliance and allow all surfaces to cool completely before servicing.
• Remove burner grates and caps as needed; lift out the old lid and seat the new lid in the burner recess.
• Inspect surrounding components (cap, electrode/igniter) for damage while installing.