Deflector Picture Parts

This splash shield kit is an OEM replacement part that prevents water from spraying beyond the door seal in Frigidaire dishwashers. The kit measures 1.5 inches in length, 0.5 inches in width, and 1.7 inches in height.  This kit is located on the front lower corners of the dishwasher tub. If your dishwasher is leaking due to a damaged or worn-out splash shield, the kit provides a reliable replacement.

Symptoms of a bad splash shield kit include:

• Stains or mineral deposits on surrounding cabinetry   
• Puddles or drips developing outside the dishwasher tub 
• Reduced cleaning ability due to unredirected spray patterns
• Damage, cracks or missing sections of splash shielding 

Causes can be normal wear from extended use breaking down barriers over time. Proper shield alignment is needed to effectively direct spray inside the tub.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Toe Panel Insulation is an OEM part for Whirlpool dishwashers. This part was designed to enhance the appliance's performance by reducing noise and preventing heat escape from the bottom of the dishwasher. This insulation panel fits snugly behind the dishwasher's toe panel, which is located at the lower front part of the unit. 

Causes of a bad Toe Panel Insulation might include wear and tear over time, damage during appliance installation or removal, or deterioration due to moisture exposure. 

Symptoms of inadequate or damaged Toe Panel Insulation include:

• Noticeable increase in noise level from the dishwasher, making it more disruptive during its operation.
• Excess heat felt near the base of the dishwasher, indicating heat loss.
• Potential for condensation or slight temperature changes in the kitchen due to the heat emitted from the dishwasher.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Hinge Brace is an OEM replacement part for Whirlpool dishwashers. It serves as a supportive bracket anchoring the dishwasher door hinge assembly firmly in place.Note: This part may be different from your original. If your original part was a flat plastic vapor barrier, the new design is a wire. It is a factory design change, the old design is no longer available.

Over time, the hinge brace can degrade due to constant use, heavy loads on the door, or accidental impacts. A faulty hinge brace can result in misalignment or difficulty in operating the dishwasher door.

Symptoms of a bad hinge brace include:

• Loose or unstable door that does not close securely
• Gaps appearing around the door seal during wash cycles
• Broken hinge components from added stress and tension on the door
• Difficulty fully opening or closing the dishwasher door

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

This ice dispenser deflector mounts in the freezer door chute to guide cubes or crushed ice into your glass. Replace a cracked or missing deflector to reduce scatter and keep ice flowing where you want it.

• Directs ice down the dispenser chute toward the glass
• Helps contain spray and bounce-back of cubes
• Restores proper flow when the original deflector is cracked, warped, or missing
• Common symptoms: ice misses the glass, ice scatters on the floor, visible damage to the deflector

• Disconnect power to the refrigerator before servicing; wear cut-resistant gloves
• Access the dispenser area per your model's instructions and note the deflector's orientation
• Transfer any screws or clips from the old part; avoid forcing plastic tabs
• Restore power and test ice dispense to confirm proper direction and clearance

The Drawer Guide is an OEM part for LG refrigerators. This part allows the smooth and effortless operation of the refrigerator's drawers, ensuring they glide in and out with ease. 

Causes of a bad drawer guide can be attributed to wear and tear over time, misalignment during installation, or damage from excessive force or improper use of the drawers.

Symptoms of a bad drawer guide include:

• Difficulty opening or closing the drawers
• Drawers getting stuck or not sliding properly
• Excessive friction or resistance when operating the drawers
• Drawers becoming misaligned or tilted
• Unusual noises or grinding sounds when using the drawers

This OEM LG part is also compatible with some Kenmore models.

This divider guide kit replaces the guide components that support and align an adjustable divider inside the refrigerator. It restores smooth movement and secure positioning so the divider stays put and your bin or basket stays organized.

• Guides the adjustable divider along its track and keeps it centered
• Helps the divider hold position to partition storage space
• Replaces cracked, warped, or missing guide pieces
• Common symptoms: divider falls out, won't stay in place, binds, or is difficult to adjust; visible broken plastic on the guide

• Unplug the refrigerator and remove the affected bin/basket and divider before beginning
• Note the orientation and fastener locations to aid reassembly
• Use the appropriate screwdriver or nut driver; avoid overtightening into plastic
• After installation, the divider slides and locks securely

This diverter valve directs wash water inside the machine, switching flow between internal paths during wash and drain/recirculation steps. Replacing a failed diverter restores proper water routing so cycles advance and complete as designed.

• Redirects water between the drain and recirculation/spray paths as commanded by the control
• Ensures correct water flow for wash, rinse, and drain steps
• A sticking or failed diverter can cause slow/no drain or no recirculation/spray
• May lead to cycle pauses/errors, unusual clicking/buzzing from the valve area, or leaks at the valve body/ports

• Unplug the washer and turn off water supply; expect residual water in hoses
• Access location varies by model; typically mounted along the pump/hoses under the cabinet
• Move hoses/clamps and the electrical connector one at a time; match port orientation
• After installation, run a rinse/drain test and check all connections for leaks

This ice container deflector attaches to the ice bucket assembly and guides cubes toward the dispenser chute. Replacing a cracked or missing deflector restores proper ice flow and helps keep ice from spilling inside the freezer during dispensing.

• Directs ice from the bucket into the dispenser chute/crusher path
• Helps maintain consistent dispensing and minimizes stray ice inside the freezer
• Replace if cracked, warped, or missing
• Symptoms include erratic dispensing, ice spilling or jamming, or a visibly damaged/missing guide on the ice bin

• Disconnect power before servicing; remove the ice bucket
• Position the new deflector in the original location; reuse existing screws/clips if applicable
• Ensure the curved face points toward the dispenser chute
• Reinstall the ice bucket, restore power, and test ice dispense

This small guide sits at the icemaker fill area and manages the water stream. It directs incoming water into the fill cup and channels any excess safely away to help prevent splashing, leaks, and ice buildup inside the freezer.

• Guides the icemaker fill stream into the fill cup/funnel during the fill cycle
• Diverts stray or excess water to the overflow path to reduce spills
• Helps prevent leaks, sheets of ice, and clumped cubes under the icemaker
• Clues it may be needed: cracked, warped, or missing guide; water dripping from the fill area

• Disconnect power and turn off the water supply before servicing
• Remove ice bin and any covers to access the icemaker fill area
• Unclip/unscrew the old diverter; align and secure the new part to the fill cup/tube
• Restore water and power; run a test fill and check for leaks

This air diverter is a duct component that directs and balances airflow inside the refrigerator. Replacing a cracked or missing diverter helps restore proper cooling performance and reduce frost or condensation around air passages.

• Guides cold air from the evaporator through the intended duct path
• Helps maintain even temperatures between compartments
• Improves airflow seal and direction to reduce warm-air bypass
• Common symptoms: uneven cooling, weak airflow, frost/condensation near ducts, or visible damage to the diverter

• Disconnect power before servicing
• Remove shelves/drawers and the interior panel to access the diverter per your model's service information
• Note orientation and transfer any reusable screws/clips
• Do not overtighten fasteners into plastic; confirm unobstructed airflow before restoring power

This module snugger is a small retaining piece used in the refrigerator to hold its associated module or component securely in place. Replacing a cracked or missing snugger restores a tight fit, reduces vibration and noise, and supports correct operation.

• Secures the related module or assembly to prevent shifting
• Helps maintain proper alignment for reliable performance
• Reduces rattles and wear from vibration or movement
• Typical signs it's needed: part is broken or missing, components feel loose, or you hear rattling

• Disconnect power to the refrigerator before servicing
• Note the original orientation and location; take a photo for reference
• Reuse existing fasteners or clips if applicable; avoid overtightening
• After installation, confirm the part holds the assembly firmly and that movement is smooth where intended

Replacement diverter overflow that helps channel excess water away from the ice maker/water system to reduce pooling and leaks. Restores proper drainage so the refrigerator interior stays dry and operates as intended. What it does:

• Directs overflow or stray water from the ice maker/water area into the drain path
• Helps prevent water pooling or dripping inside the freezer or cabinet
• Use when you notice leaks, water pooling under shelves, or water coming from the dispenser/ice area

• Always disconnect power and shut off the water supply before starting any repair
• Removal of interior shelves/trim or access panels may be required to reach the diverter
• Handle plastic tabs and clips carefully to avoid breakage; replace any damaged fasteners

This refrigerator deflector is a molded guide that mounts inside the unit to direct internal airflow where it's needed. Replacing a cracked, warped, or missing deflector helps restore proper circulation for more consistent temperatures and performance.

• Channels airflow within the freezer/dispenser path to maintain even cooling
• Helps reduce frost or ice buildup caused by misdirected air
• Can address symptoms like warm spots, frost around vents, or rattling from loose parts
• Replace if broken, deformed, or missing

• Disconnect power before servicing
• Remove shelves/panels as needed to access the mounting location; keep track of screws/clips
• Install the new deflector in the same orientation; reuse existing hardware
• Reassemble and verify that vents/air passages are unobstructed

This replacement funnel guides dryer airflow from the drum into the lint screen housing. Replacing a cracked or missing funnel helps restore a tight air path for efficient drying and keeps lint contained inside the proper ductwork.

• Directs exhaust air from the drum into the lint screen/duct path
• Helps prevent lint blowback and cabinet contamination
• A damaged or warped funnel can cause longer dry times and poor airflow
• Contribute to excess lint in the drum or overheating symptoms

• Disconnect power; for gas models, also shut off the gas supply
• Access is typically through the top or front panel; remove lint duct fasteners as needed
• Transfer and reuse existing mounting hardware and any seals
• Clean lint from mating ducts and ensure an airtight fit before reassembly

This deflector directs dishwasher spray water for proper coverage and helps protect nearby components from direct spray. It replaces broken or warped deflectors to restore intended water flow and cleaning performance. What it does

• Guides spray water toward dishes and spray arms to maintain even coverage
• Prevents direct spray from hitting sensitive components or seals
• Helps reduce spotting and uneven cleaning caused by misdirected water
• Fits where the original deflector is mounted; replaces cracked, broken, or deformed pieces

• Turn off power and water supply to the appliance before starting any repair
• Remove the lower rack or other obstructions for clear access to the mounting area
• Inspect mounting tabs and surrounding components; replace any damaged clips or fasteners

This replacement deflector redirects airflow and shields nearby components to help restore proper circulation and protect internal parts. It's a simple, serviceable part that can correct airflow-related performance issues when damaged or missing. What it does

• Redirects and channels airflow to support even drying/heating or optimal ventilation
• Shields internal components from direct airflow, debris, or splash damage
• Helps reduce performance issues tied to disrupted airflow or damaged seals
• Fits into the appliance's airflow/vent path to maintain designed circulation

• One deflector

• Designed for direct replacement; follow factory service manual for removal and re-installation
• Disconnect power (and gas if applicable) before servicing to avoid shock or injury
• Use appropriate hand tools; avoid force that could damage mounting tabs or adjacent parts
• Inspect and replace those components as needed