Degx-1 Parts

This shield duct inlet directs dryer exhaust and protects the cabinet opening where the vent connects, helping maintain proper airflow and reduce lint intrusion. It restores a secure, sealed connection between the dryer and the vent duct. What it does:

• Guides exhaust airflow from the dryer into the external vent to help efficient venting
• Shields the cabinet opening to prevent lint and debris from entering internal components
• Helps reduce air leaks at the duct connection that can lower drying performance
• Stops rattling or loose duct connections by providing a stable mounting surface

• One shield duct inlet

• Disconnect power (and gas supply for gas dryers) before starting work
• Verify orientation and fit before fastening; replace any damaged fasteners or gaskets
• Reinstall panels and secure duct clamps/screws to ensure a tight seal
• Run a short test cycle and inspect the duct connection for leaks after installation

This drum bearing kit replaces the rear support bearing that helps the dryer drum rotate smoothly. Restoring the bearing reduces noise and wobble for steadier, more reliable drum operation. What it does

• Supports the rear of the dryer drum so it turns freely
• Reduces grinding, squealing, or rumbling noises from the rear of the dryer
• Helps stop excessive drum wobble or uneven spinning
• Protects the drum and bulkhead from wear caused by a failed bearing

• Disconnect power to the dryer before any service to avoid shock or injury
• Access typically requires removing the dryer rear panel or drum; follow the OEM service instructions for your model
• Inspect drum seals, rollers, and the shaft for additional wear while installing the bearing
• Use appropriate tools and fasteners

The Thermostat Auto Reset is an OEM replacement part for Fisher & Paykel electric and gas dryers. Precisely located within heating circuits, it monitors internal air temperatures and automatically resets the thermostat when needed. 

Causes of a faulty reset thermostat can include:  

• Fluctuating or inconsistent vent temperatures   
• Frequent on-off cycling of gas valves or heating coils
• Triggering of drying error codes and safety shutoffs
• Inability to detect correct drying time end points

Symptoms involve temperature swings, premature shutoffs, and unfinished loads. Long term exposure to heat or combustion byproducts can degrade sensor function over time. 

The Safety Thermostat is an OEM part for Fisher & Paykel dryers. As an important safety device, the thermostat monitors the dryer drum temperature and automatically shuts off the dryer if temperatures become excessively high. It plays a protective role by preventing overheating that could pose a fire hazard.

Causes can be normal wear and tear over extended use.  
Symptoms of a bad safety thermostat include:

• The dryer failing to heat or heating unevenly
• Abnormal drying times as heat is improperly regulated
• Shut offs mid-cycle accompanied by flashing lights or error codes

This display kit replaces a failed dryer control display so you can see and select drying cycles and settings. It restores visible status feedback and allows normal control-panel operation for troubleshooting or repair. What it does:

• Replaces the dryer's front control/display assembly to restore on-screen indicators and control input response
• Makes cycle status, temperature, and timer information readable again
• Helps resolve symptoms such as blank or non-responsive display, missing indicators, or unreadable characters
• Works with the existing control harness and front console so normal button presses register correctly

• Disconnect power before servicing to avoid electrical shock and damage
• Remove the dryer top or front panel per service manual to access the display assembly
• Handle the display carefully to avoid scratching or bending the panel and ribbon connectors

The Lint Filter Retainer is an OEM part for Fisher & Paykel dryers. It serves as the housing or frame that securely holds the lint filter in place during the drying cycle. This retainer ensures proper positioning and alignment of the lint filter, allowing efficient airflow while trapping lint and other debris.

Causes of a faulty lint filter retainer can range from physical damage or cracks in the retainer itself to worn or broken mounting clips or hinges that secure it to the dryer chassis.

Symptoms of a bad dryer lint filter retainer include:

• Lint filter not staying in place or falling out
• Airflow obstructions leading to poor drying performance
• Potential safety hazards from a dislodged or missing filter

This OEM Fisher & Paykel part is specifically designed for their dryer models, guaranteeing a perfect fit and seamless integration with the appliance's lint filtration system. 

A replacement lint scraper that helps clear trapped lint from dryer drum areas to maintain airflow and drying performance. Fits the OEM position used to remove lint buildup for safer, more efficient operation. What it does:

• Scrapes and dislodges lint and debris from drum seams and nearby housing areas
• Helps restore airflow to reduce long dry times and overheating risk
• Reduces lint-related odors by removing trapped fibers
• Works as part of routine dryer maintenance to support reliable operation

• One lint scraper

• Disconnect power (unplug or turn off breaker) before working on the dryer
• Allow the dryer to cool completely before accessing the drum area
• Handle carefully; avoid forcing the part into place and inspect surrounding seals and fasteners

This manual-reset thermostat is a temperature-sensing safety cutoff that interrupts power when temperatures rise above a set point, helping prevent overheating in the appliance. Replaces a tripped thermal cutoff so the unit can be tested and returned to service. What it does:

• Acts as a temperature-activated safety switch that opens when the sensor detects excessive heat
• Stops current flow to the affected circuit to help protect components from overheating
• Allows manual resetting after the unit has cooled and any underlying fault is fixed
• Commonly used where a single, resettable over-temperature protection device is required

• Disconnect power before replacing—electrical shock hazard
• Verify the cause of the over-temperature condition before resetting to avoid repeat trips
• Match wiring and mounting orientation to the original part for proper operation

This jockey pulley kit replaces a worn idler pulley that keeps the dryer belt tensioned so the drum turns smoothly. Restores proper belt tracking and reduces noise from a slipping or misaligned belt. What it does:

• Maintains correct belt tension to help the drum rotate evenly
• Supports the drive belt and prevents slipping or premature wear
• Helps eliminate squealing, grinding, or rubbing noises from the dryer
• Reduces uneven drum movement or stopping caused by a failing pulley

• One jockey pulley kit

• Disconnect power (and gas supply on gas dryers) before beginning any repairs
• Inspect the drive belt and related components; replace any worn parts simultaneously
• Use recommended tools and avoid forcing fasteners; follow OEM torque guidance if available

The Dryer Leveling Leg is an OEM part for Fisher & Paykel dryers. It securely elevates and stabilizes the dryer unit on any floor surface. The leveling leg allows for balance, and level adjustment, and protects against moisture concerns.

Symptoms of an insufficient leveling leg include: 

• Dryer rocking or wobbling noticeably during operation
• Premature wear of internal tumbler bearings  
• Vents or doors failing to seal properly

Causes of a faulty leveling leg can be damaged from repositioning the heavy dryer on uneven flooring. Over time, repeated stress leads to fractures of mounting points. 

This is a stainless steel #8 x 5/8" Phillips screw sold in a pack of 10 — a direct-fit fastener for appliance panels, brackets, and trim. Durable corrosion resistance helps maintain secure assemblies over time. What it does:

• Fastens panels, brackets, trim pieces, and other appliance components using a Phillips driver
• Stainless finish resists rust and corrosion in humid or wet appliance areas
• Sized for common appliance mounting points where #8 x 5/8" screws are specified
• Helps restore loose or missing fasteners that cause rattling or poorly seated panels

• Ten (10) stainless steel #8 x 5/8" Phillips screws

• Use the correct #2 Phillips bit and moderate torque to avoid stripping the head or damaging mating parts
• Tighten until snug; do not overtighten plastic components
• Disconnect power to the appliance before accessing internal panels or wiring
• Keep loose screws away from children and dispose of packaging responsibly